# How Long Should I Run My Pool Pump?

The above question is posed to the likes of me (pool industry folk) on a regular basis. Actually strike that – I impose the answer to that question on homeowners every day because I am tired of seeing them throw away good money.  A pump does not need to run 24/7 to keep your pool water pristine. If properly sized, a pump should spin through your water in a fraction of the time, allowing it to be dormant for the rest of the day. Thereby, relieving your wallet of the heavy burden of high electric bills.

## Well, What Is the Answer, Smart Guy?

Residential pool water only needs to be turned over once daily to have proper filtration.  Twice through the filter may be necessary after heavy usage such as a pool party. Only commercial pools require water to be turned several times a day to maintain proper sanitation. Anything more than a 1-2 filter cycles in a day is superfluous, almost as superfluous as someone using the word superfluous.

The key to a properly sanitized pool is not only filtered water but also well-balanced water chemistry. If your water is unbalanced then issues will arise no matter how much the water churns. A good once through your filter system should alleviate you of troublesome bacteria barring some kind of major chemical imbalance.

## How Do I Calculate a Filtering Cycle?

With a few measurements and some math (oh no!) we can assess our proper pump run time.  Before we begin we will need a few things: overall dimensions of your pool including length, width, and depths (shallow and deep ends), the model number of your pump, and a rough estimate of the length of pipe to your pool (feet of head.)

### Calculating Pool Gallons

To know how long to filter, we need to know how much we are filtering.  For this step, we will be using a trick of trade called the Pool Volume Calculator by Penair.  This easy to use calculator provides your pool gallonage in a few keystrokes. No complex volume formulas for this guy.

For our example, we will say our pool is a total of 24,000 gallons.

### Pumping for Information

Now we must determine the approximate water flow produced by our pump. For this we must know the model number of the pump and the feet of head of the pool. Again, the feet of head is the average length of pipe leading from the pool’s skimmers and main drain to your pump.

For our example, I have chosen a Hayward Super Pump 1.5 HP Single Speed, model number SP2610X15. And for our imaginary pool the length of pipe to the main drain is 20 feet and the pipe feeding the skimmer at the other end of the pool is 60 feet, totaling an average of 40 feet of head.

20 Feet +  60 Feet = 80 Feet

80 Feet ÷ 2 Pipelines = 40 Feet of Head

Using the model number SP2610X15 and calculated feet of head on the below chart we can see that the approximate rate of flow is 65 gallons per minute (GPM.)

### And then…..

The hard part is done but we still have 2 more calculations to complete to determine the run time for one filtering cycle of our pool. Using the numbers we deduced from previous calculations we use:

24,000 Gallon Pool ÷ 65 GPM Flow Rate = 369 minutes for full-cycle

369 minutes ÷ 60 Minutes = 6.15 Hours for Filtering Cycle

And there is the answer,  6.15 hours filtering time will cycle your water once.  This equation can be applied to any pool and adjusted for any run time. We normally suggest having a run time of 6-12 hours for filter cycles.

As usual, if after reading our blog posts more questions arise or there is a further explanation needed, do not hesitate to call our techs at 877-372-6038.

## 65 thoughts on “How Long Should I Run My Pool Pump?”

1. Brittaney Moder says:

I admit, I have not been on this webpage in a long time… however it was another joy to see It is such an important topic and ignored by so many, even professionals. I thank you to help making people more aware of possible issues.

2. Harold Hoyt says:

Question is on how long should a commercial pool run for cond of 24 units . People use the pool every day there is sun .the bulk of People are in and out of the pool from 10am to 6:00 pm . I would say a average is 10 people in and out multipal time daily . Mostly sunning and they use the pool to cool off . But at times group of people may hang in pool for 3 to 4 hour just talking and enjoying the nice 90degree water . Some exercise , often guest of owner with families and children . Currently the pool runs 24 hours a day , cleaned weekly by out side co. Water temp and clarity are well maintained . We are currently happy with quality of pool water but a new owner feels it’s a wast of energy to run 24 hours . We are informed that another condo only does 12 hrs daily but they hardly ever have usage . If the concerns of the new owner is correct then let it be . My only concern is its the best maintained pool I have used and do not wish to see it decline .

1. Runtime of commercials pools is a bit trickier to estimate because of the higher bather load. Commercial pools do not have a long recoup time to restore chlorine levels before the next batch of swimmers dip in.

With your situation, I would use a “dial it in” approach, cut the run time by 4-hour increments at a time. Run the pool for 20 hours a day and see how it reacts for a week. If you get down to a 16 hour run time and everything looks fine you should be seeing a healthy savings on your electric bill. But if you see you water becoming hazy, sluggish or green, you’ll know you need to run it longer.

Let us know how it plays out.

2. Anonymous says:

I agree we live in Alabama with lots of hot sun and temps, Lots of rain to go with it so algae can be bad at times, So we run our pool sand filter pump 24/7. We have an ionizer and found at time we also need to add Chlorine .

3. Passerby says:

I think this would be the best way to approach this, which is what I think you attempted and just got the terminology mixed up a bit, same result with better clarification of what your doing, no worries it happens:

24000 gallon pool (divided by) 80 gallon per minute flow rate (equals) 300 minutes of run time to turn he pool over once.

300 minutes of run time (divided by) 60 minutes in an hour (equals) 5 hours total run time

🙂 cheers
Great article

4. Andy says:

Does the winter run time vary for an infinity pool ?

5. Terry says:

Answer in last calculation correct but units are not.

24,000 gallons / 80GPM = 300 minutes for full cycle
300 minutes / 60 minutes per hour = 5 hours

6. Steve k says:

My question on pump run time is there any difference when you have a salt water generator (SWG)? Probably a stupid question…. but my seconnd season of owning this inground pool (2400) gal. Thanks I’m sorry I meant to say 24000 gals.

1. It being a salt pool should not affect your run time. If you do see your chlorine levels lagging, then you can up your output percentage on the control box.

7. Jaime says:

Can I run the pump at 6am-8am and then again from 8-10pm to give me the proper filtration? That is the normal time I am using but during the day when electrical prices are high.

8. Kristii says:

I have the same question as Jaime. I live in the desert and trying to avoid running my pump during peak hours. I see that having a SWG doesn’t matter, you stick with looking at running to get a full filtration cycle each day, however, do I need to factor in that I will be losing/gaining a large amount of water from evaporation when the temps are 110 +? or is this when I pay attention to the chemical levels due to new water?

9. Flavia Bevill says:

I’m very much wanting a small little pool : Intex 6′ x 20″ Easy Set Inflatable Swimming Pool with 330 GHP Filter Pump. Husband is concerned about the electricity. How many hours would we need to run the pump and if not using every day could we run it every other day. It’d only be used a couple of hours by two adults. Thanks for the help!

10. Renee says:

Our in ground pool is 18×36..how often should I leave the pump on..should I run it during the day and shut it off at night? Thank you?

1. Renee,
That is the topic of the article you are posting on, in which I cover everything you need to figure out for yourself. Our authors take the time to write these articles, please take some time to read it.

1. Sapa says:

Lol. Thanks bud. I was thinking the same thing.

2. Anonymous says:

That was rude!

3. Jim says:

Not rude. True.

2. Ralph says:

we have a 7000 gal pool we were told 1 hr for every 10 degrees i.e. 100 degrees 10 hours True or False?

1. I have not heard that rule but I would say it is not accurate. Because you would have to assume that all pool pumps push the same amount of water, which is definitely not true. Varying horsepowers and pump models will have vastly different flow rates.

And, how long would you run your pool if it was 27,000 gallons?

11. Anonymous says:

Tom,

I’m closer to 90 than 80 in age and our pool is never used. Seriously, from year to year no one sticks a toe pool in it since the time all our grand kids became adults. Under these circumstances all I want to do is keep the pool water clean-looking for aesthetic purposes; I could care less how sanitary it is for use. Any suggestions for minimizing maintenance costs such as running filter less?

1. Well, the easy route would be to just keep shortening your run times every couple of days and test it. If the pool is maintaining its clarity and chlorine levels, then knock the run time down by an hour or two, then repeat the testing. Lower the run time until you start to see dips in water health.

1. Anonymous says:

Thanks Matthew, sounds like a reasonable suggestion to me. I’ll give it a try.

12. Orange says:

this link does not work “Pool Volume Calculator by Penair.” so Matthew, while I read the article, I could not complete the instruction given the 1st link did not work.

1. It looks like Pentair changed the location of their calculator, the link has been fixed.

Don’t forget there’s always Google to search for such things.

13. Vince says:

I have an approximately 26,000 gallon pool. Assuming I want to run the pump for 8 hour per day, it would take about 54GPM. Say I have 45 ft of head and
I have a Sta-rite intellipro 2 vst, what rpm would I need to run at to get 1 full cycle? I kind of lost you there under the “pumping for information” part of your article. I checked the performance curve for the pump and my wild guess would be about 2500rpm. Is this correct?

1. Going by this performance curve in the owner’s manual, the range would be between 2500 to 2800 RPMs.

14. Vince says:

Ok so I think I’m on the right track here. Its seems that feet of head is a constant number so what I don’t understand is that if there’s 45ft of head, based on the performance chart why would I run the pump at anything under 2500rpm to get flow. If the pump is running at 1400rpm, how would I read the chart at 45ft of head??? Many people run low rpm for several hours a day so i feel a little lost. Thank you for the help.

1. Once the pump is primed on at the higher RPMs, it should be able to hold that prime if you drop below 2000 RPMs.

Also, looking at other’s pool pump settings and comparing to your own is a good way to go batty. Even pools of similar sizes have different plumbing configuration, pipe dimensions, and pump models, making it hard to make an apples to apples comparison.

1. Lynda says:

I have the same question as Vince. I have the same intellipro variable speed filter with a 8616 gallon pool and 44 ft of TDH. My installer suggested 35gpm for 4 hours at about 2450 RPM. But what if I want to save money and run my filter for longer than 4 hours at a speed lower than 2450 RPM? The way I read it, the graph doesn’t appear to allow for running the filter at anything lower than 2450.

1. Yes, you can run it at a lower speed for longer RPMs to save money. Unless you have a flowmeter you’re going to have to figure out what RPMs and runtime by some trial and error. The flowmeter tells you how many GPM are being pushed by the pump as you slide up and down the RPM scale. This allows you to use the formulas in the article.

Without a flowmeter, a trial and error test where you lower your RPMs and raise your run time will be necessary. Extend the run time by two hours but drop the RPMs by a 1000 and let it run for a couple of days. Test your water at the end of the two days to see how it is reacting. If all is well, keep lowering the RPM and testing the water until you see a change in water chemistry. When the water starts to turn, extend your run by an hour or so. Keep playing with the RPMs and runtime until you find your max savings. You could end up with a 14-hour cycle at 800 RPMs.

1. Lynda says:

Answered my question perfectly. Thanks so much!!

2. Martin says:

As an engineer in a former life, the head is the vertical distance that water has to be lifted by the pump, no?

1. Tom Mc says:

Good question. What is the comparison of vertical head loss to horizontal pipe length head loss??

15. Carolyn says:

You referenced a chart when calculating the rate flow, but I don’t see a chart. Was it removed?

1. Jeff says:

Yes, I don’t see it either

1. I posted an updated flow chart for the Super pump and adjusted the necessary math.

16. Lary says:

Hello, I have an average-size saltwater pool in Sacramento and it’s not used during winter months (November-March). It gets cold during winter, but not freezing temperature cold. Question: Should I turn my pump off completely (will it damage the water?), or how long should I run the pump daily during winter months (while cold, but not freezing)? If I still need to run it, can I skip a few days weekly to preserve energy and extend motor life? Thank you!

17. lucy says:

HI there, I’ m pretty bad with the calculation. I have a 8 x 4 meters pool, 1.2 meters deep. I don’t use it during the winter time either, how many hours do I need to keep the pump running per day to keep the water clean? The electricity bill has been very expensive, i really want to work out an efficient way to save on the bill. Thanks a lot.

1. As the article mentions, the size of the pool is just part of the calculation. We need to know the feet of head of your pool plumbing and the model of your pool pump. If you do not have that other info, then you can use a flowmeter to gauge the strength of water flow. With the flow figured out, you can use pool volume calculator in the article to find your pool gallons.

1. lucy says:

18. Perry michael says:

I have a new pool, 21000 gal, and an electric cover. Planning to install a salt system and trying to decide between a Hayward super pump I already own or using a variable speed pump. So I’m not sure if it is covered 90% of the time can I circulate the water less? Am I better off using a variable speed pump in this setup?

1. If the pool is covered most of the time, that means you can run your pump less. The less exposure to the elements, the less chlorine is burned off and fewer particulates dirt and grime accumulate in the water. A single speed should be fine, but you could always replace the old single speed motor with a variable speed. It is cheaper than the whole pump and will save you money in the long term. V-Green 1.65 and the 2.7

19. RobertC says:

Am I calculating this wrong? The measurements of the pool show that I have a 12,187 gallon pool. The head is 30 feet average. The pump is made by US motors and says 3450 RPM on it. I am coming up with about 73 minutes per day?

1. To figure out the runtime we would need to know the model number of the pump housing. US motors just make the motor, and that motor can be fitted to dozens of different pumps with varying flow rates.

1. RobertC says:

I looked all over the pump housing and did not see any type of label anywhere, is there a general guideline that I can go by?

1. Not really, because not all pumps are made equally. A 1 hp pump in this model may do double the GPM output of this other 1 HP pump. Consider it like this, could you guess the 0-60 time of a vehicle if the only info you had was that it had four wheels and motor? Probably not.

You can try opening the pump to take a look at the impeller number.

1. RobertC says:

I looked at 1 of your other posts about replacing equipment that you cant find a model# for. I looked on the strainer lid as that post suggest and found the number C3-139P, does that help?

2. As I said before, I need the number of the impeller. The impeller is on the inside of the pump. It is a disk with fans that is attached to the end of the motor shaft.

20. Mike says:

Matt i replaced my old single run pump with a variable speed pump and i recently replaced my worn out swg as well-We live in the desert with temps in the 100’s and i need to run my pump longer to get the chlorine needed to keep it up–So i am turning my water 3-4 time a day to do this–12000 in ground pool pump set at 1500 for 12 hours a day.Lower speed for long times is what i am reading–Is this correct and is it bad to turn the water that much.And i have my swg set at 100% ?Some are saying run it at a even lower speed for longer time to keep up?

Any thought on this?

Mike

1. What is your swg rated for? How many gallons? What are your chlorine levels? it is hard to say if you are doing it too much without knowing what your water chemistry is.

The point of having a variable speed is to run it for long periods on low speeds but if your chlorine generator can’t handle the boy of water and temperatures, you may be forced to keep running the system in this way.

21. Suzanne says:

I have a 27′ above ground pool and was told I need to run the pump constantly because there is only one return. I have a 2 1/2 hp on hi speed and maybe 1 1/2 hp motor on low & my pool holds 17,000 gallons. My question is should I run it constantly?

1. You would not need to run the pump constantly in most cases. This article helps you figure out how long you need to run your pump.

22. Beau says:

Something I find most don’t seem to consider is that many pools use a tab chlorinator. However that chlorinator is an ”inline” device. So if they water isn’t being filtered, it also isn’t being actively chlorinated either. I know several people who run their pumps much longer (16-20 hours a day, variable speed) and the result tends to be much more consistent (better) pool chemistry. Particularly in the south where the sun rapidly destroys the chlorine.

23. Old Pump Guy says:

Head Feet is measured in the vertical distance a pump must push rather than the horizontal.
To determine the head feet at which your system is operating, take the pressure shown on your filter pressure gauge and divide by .4335 Example 20 PSI /.4335 = 46 feet of head.

Hope this helps

24. Wiredawg says:

Thanks for the great information. I had a quick question. When factoring the time I want to run the pump it seems reasonable to include the amount of time I run the vacuum and the skimmer. Would you include both of these in the calculation. I run my vacuum at 2800 RPMs and the pool/skimmer at 1400 RPMs. Would you figure your turnover rate with the two cycles independently and then just make sure you are turning over the water once a day? Thanks

25. Fred Luhn says:

Not real sure how anyone can say you need to run your pump for “x” hours to turn your water over one time if your pool is “x” gallons and your pump is rated at “x” flow and your pipes are “x” long. That formula would work if you were pumping the contents of your pool into another pool but isn’t at all accurate if you are recirculating the water as all pools do. Why? Because some of the water that’s been filtered already gets filtered again right away while some of the water may not have had time to make it through the pump at all in the time span of a few hours. Every pool’s circulation pattern is different. Some are more efficient and others less efficient. I would think it’s best to start high like a 12-hour cycle and slowly back it off a couple of hours at a time until you see poor results then bump it up an hour or two. That will then be your proper time cycle to run your pump.

26. Anonymous says:

I calculated the amount of water exchanges I have to do. I was wondering if it matters the time of day it is better or worse to run a pump? Ie. Better to run during the hot sun of the afternoon or better at night or does it matter?

1. in my experience, running the pump during the day had the best results. Chlorine gets burned off by the sun, so running your pump during the daytime ensures that your chlorine level stays at an adequate level. The downside is that it is more costly to run during the day due to peak hour electricity costs. So you may want to consider running you pump for 4 or 5 hours during the hottest parts of the day, then supplementing it with a few hours at night.

27. Richard says:

I am not really worried about the cost or clarity, although both should be OK, I am more looking at the benefit to the actual pump by running it 24/7. Is it really better for the pump to run continuously? Will I get a longer life out of it on average? Pentair VS that I can run at a low speed for much of the day and run higher speed some of the day and never turn off.

28. Finesse says:

How long do you run the pool pump after adding 5 gallons of muriatic acid for a no drain acid wash? Was told run it for 24 hours for 5 days (brush daily) by the pool company. Is that accurate or can I run it for 6 hours for the remaining 4 days instead? It has already been on for 12 hours.

1. Yes, the 24 hours a day for 5 days sounds about right. The run times we are referring to in the article are for everyday use, not specific chemical treatments as in your situation. I would stick with what the pool company recommended if you want the treatment to work.