high head and medium head pool pump

Which is Best: High Head or Medium Head Pumps?

After my last article on how to calculate the total dynamic head (TDH) of your swimming pool, I decided to tackle a subject in a similar realm: high and medium head pumps. In the Total Dynamic Head (TDH) blog post we explained that TDH is essentially the force/resistance working against the pump as it pushes water through your pipes. The higher the feet of head, the harder your pump needs to push to counteract that resistance.

Calculate your feet of head according to the blog post or your choice of online calculator and select the style of pump accordingly:

  • Medium Head Pump < 65 Feet of Head
  • High Head Pump > 65 Feet of Head

To illustrate our devotion to this topic, here is our contributor, Patrick, describing high pressure and high flow in a video from years back:

medium head pool pump flow chart
Uprated Horsepower Rating: A = .75, B = 1, C = 1.5, D = 2, E = 2.5
high head pool pump flow chart
Uprated Horsepower Rating: G = .75, H = 1, I = 1.5, J = 2, K = 2.5, L = 3.5

The Pentair Challenger Series offers a gleaming example of the difference between high head and medium head outputs. The Challenger is a rare pump in the series that offers both a high flow and high pressure. The pump curves show a comparison of flow rates in congruence with horsepower and feet of head.

The High Flow Challenger on the right shows a sharp dip as the feet of head pressure rises. On the other hand, the High-Pressure Series keeps a steady rate of climb as the feet of head peaks. The two styles of Challengers are virtually identical besides the impeller and diffuser designs. These parts turn the spinning force of the motor into pumping action.

Medium Head Pumps (aka High Flow Pumps)

Medium head pumps, also known as high flow pumps, are the most common types found on pool systems today. A basic swimming pool set-up that lacks an attached spa or other water features like waterfalls will usually not require anything more than a medium head pump. High flow pumps are ideal for pools with 35-65 feet of head pressure.

click here to find your replacement pool pump parts

Popular Medium Head Pumps

Hayward Super PumpPentair Challenger - High FlowPentair Whisperflo
Blog Image - Super PumpBlog Image - Pentair ChallengerBlog Image - Pentair Whisperflo
Hayward Super PumpGo to Pentair ChallengerGo to Pentair Whisperflo

High-Pressure Pumps (aka High-Performance Pumps)

If your pool has a spa attached or your poolscape includes waterfalls, deck jets, or bubblers that draw from your main pump, we seriously suggest installing a hardy high pressure pump. All those aforementioned add-ons are tacking on yard after yard of feet of head pressure that would slow the flow rate of a medium head pump to a trickle. High pressure pumps earned that name by being able to push water through long lengths of pipe without suffering heavy drop-offs in flow.

High-pressure pumps are ideal for pools with elevated solar heaters. The value of head pressure also accounts for the rise (or lift) of water as it travels through a plumbing line. The feet of head and rise in feet have a 1:1 ratio. A solar heater may tack on 10 to 20 feet of feet of head from elevation alone. Once you add the extra length that is racked up by the coiled heat exchangers you may face 30 feet of head on top of your standard pool plumbing.

Popular High Head Pumps

Jandy StealthJacuzzi MagnumPentair Challenger
Blog Image - Jandy StealthBlog Image - Jacuzzi MagnumBlog Image - Pentair Challenger
Go to Jandy StealthGo to Jacuzzi MagnumGo to Pentair Challenger

11 thoughts on “Which is Best: High Head or Medium Head Pumps?

  1. I’ve swapped out and replaced part # for part # on my 2 HP Challenger:
    Shaft Seal
    Mounting plate
    Impeller
    Diffuser
    Volute
    Band Clamp
    O-rings

    Getting a small continuous drip at seal plate and housing….don’t understand why. Pool guy comes in and changes out the diffuser and impeller to a 1HP version. no leak now, but pop ups are barely popping out water. Also paramount water valve is reading 30 PSI, never been that high.

    is the 2HP impeller/diffuser high pressure parts too much? should it be 2HP impeller/diffuser high flow instead? like i said, i swapped out part # for part #….

    1. So I am a little confused. Did you switch to a 2 hp from a 1 HP, vice versa, or is there a mistype in there somewhere? Because in your comment it sounds like you have switched HP or something but also go on to say you have switched like for like by using the same part number.

      1. Challenger pump with 2 HP motor. I personally replaced mounting plate/impeller/diffuser/seal plate(355317/355604/355545/355303)…these are the exact part numbers I removed from what was in place when in working order.

        Upon replacing the above said parts, I got a leak at the bottom of volute/seal plate which was not the original issue.

        Given that I replaced everything new, and I got a leak, I decided at this point to call in a professional. Their diagnosis was it was leaking because 2HP was too much force. Their solution was to keep the 2HP motor and replace diffuser/impeller to the 1HP version(355074/355077).

        1. Their diagnosis doesn’t make much sense if the pump was fine until a set of like for like parts were installed. The two horsepower would also put out more flow, so there shouldn’t be a pressure issue unless your filter is dirty.

          My first instinct when I see a leak like that is to break down the pump and redo the steps of installation to ensure everything was done correctly.

          1. The 6 port water valve was also diagnosed as “bad” and encouraged to be replaced, so I did that. All 2 HP parts were put back on and and pump replumbed… leak at seal plate.

            By process of elimination, removed the water valve and voila…no leak. put the old water valve in that was suspected as bad…also no leak.

            Why would a new water valve cause leakage at the seal plate? definitely a strange one…

  2. I have a WhisperFlo WF-28 on my pool right now, but it’s getting ready to die. I’m figuring out what to replace it with and was going to just get a motor for now as the pool is ~15 years old so the heater, filter, booster pump, etc are all going to need replacing in the next couple years anyway.

    My problem is that I think the WF-28 might be undersized. I calculated my TDH using your charts and I arrived at 165 feet (there’s a spa, two drains 6.5 feet deep, and 5 returns so all those joints really added up, I think). From the WF-28 charts it looks like it’s not rated for this many feet.

    So my question is, can I get a high pressure motor to replace the motor on the WF-28 or should I replace the whole pump? I assume the whole pump because I’m guessing the whole unit is built to either handle the high pressure or medium pressure.

    Am I correct in my logic? Does 165 feet of head sound crazy? Since I’m looking at an overhaul in the next year or so can I get by with a WF-28 replacement motor and just run it longer?

    1. I’m going to be honest, I am a little skeptical of the feet of head measurement. read through this other guide to get a clarification on feet of head: How Do I Calculate Feet of Head for My Pool?

      Also, if the WF28 was working fine for however many years, I would keep the setup as is, unless there is a sudden needs to turn over your water more. If the feet of head was 165 that pump probably wouldn’t be able to prime itself let alone pump enough water to keep the pool clean. A replacement 2 HP motor (B855) for the WF28 is available or you can go up a horsepower, but if you upgrade the motor you will also need to change the impeller.

  3. Hi sir, got a pool under construction with volume capacity of approx 26,124 gallons (US) which should be filtered every 8 hrs. Average flow head of skimmers and drains is 40 feet. Before I purchase, please advise me on the appropriate size of the most energy efficient pump and filter suitable to this size of pool. Thank you.

Leave a Reply

Your email address will not be published.

Recommended Resources

How To Prime a Pool Pump

October 8, 2020

How To Prime a Pool Pump In this Pool Care Basics, we show you how to prime your pool pump with a garden hose after it has lost prime. This is useful when your pump is struggling to achieve prime on its own.

Watch Now
Does it make sense to repair my pool motor?

Does it Make Sense to Repair My Pool Pump Motor?

When it comes to a failed pool pump motor, the pool owner is faced with that eternal question, “repair or replace?”...
Read Now
Disassembling a Pool Pump - Tips & Tricks

Disassembling a Pool Pump – Tips & Tricks

We here at INYO pride ourselves in being upfront about pool and spa maintenance and being more than willing to help...
Read Now

5 Biggest Swimming Pool Mistakes

There are many common swimming pool mistakes and oversights committed by home owners, however innocently.  This overview of pool fails will help...
Read Now

Looking for pool parts?

Shop Motors Shop Filters Shop Pumps Shop Salt Systems Shop Lights Shop Cleaners
Copyright © 2024 INYOpools All rights reserved