By Goldline Controls


Details

Top

Model # AQL2POD

Manufacturer Code AQL2-POD

Product Description

Thanks to its sealed design and fully rechargeable battery, Aqua Pod isn’t just water resistant, it’s completely waterproof. It floats horizontally, making it easy to find in the pool, and its backlit LCD display offers better viewing – even at night. It’s also totally programmable. When teamed with Goldline® Controls’ Aqua Logic® pool and spa automation, Aqua Pod delivers unprecedented control over everything from water flow and temperature to filtration and custom light shows when paired with ColorLogic® from Hayward®. No matter where you are – in the house, by the pool, even in the water.

Aqua Pod Features:

  • Easy to operate
  • 100% Waterproof and floats horizontally
  • Built-in rechargeable batteries; charging station included
  • Full functional control of pool, spa and other outdoor features
  • Backlit display for convenient nighttime viewing
  • Remotely programs and controls Aqua Logic
  • Multiple heater and chlorination controls
  • Programmable group functions
  • Operates while charging
  • Upgradable software, dual equipment capable
  • System Off button for added safety
  • 3 programmable ”Soft Keys”
  • Light dimming control on incandescent lights (requires dimmer relay)
  • Simple menu navigation – no scrolling through long lists
  • Functions with multiple Goldline Controls wired and wireless remotes
  • Built-in battery – no compromise to waterproof seal
  • Software Version 2.6 or higher is needed for this remote

Aqua Pod Specifications:
Range- Up to 500 ft.
LCD Display- Backlit for easy night viewing
LCD Display- Indications Battery life, range, water and air temperature, date, time
Size- 2.43” W x 7.75” H x 1.14” D (3.29” display area width)
Weight- 0.50 lb.
Battery Life- Minimum of 500 charge/discharge cycles
Battery Life Before Charging- 400 commands or button presses
Battery Conserve- Goes into sleep mode 1 minute after last button press
Standardization- ETL

Charger Specifications:
Size- 4.0” W x 3.25” H x 4.13” D
Weight- 0.65 lb.
Power- Plugs into any standard 2-prong AC outlet
Charge Time- 6-7 hours (the unit can be used while charging)

**NOTE: Requires the Wireless Antenna Base - AQL2-BASE-RF.**

Top

?     Asked on 4/4/2008by Guest

The website states that software version 2.6 is needed to use this remote. I am currently using rev 2.43.. My questions is, how do I get the update to 2.60?
 Reply

A  Answered on 4/4/2008 by InyoPools Product Specialist Patrick P.

The software revision can only be changed by replacing the main PCB board. This would be a GLX-PCB-Main.
 Reply


?     Asked on 4/24/2010by Guest

Do i need anything else to use this with my AquaLogic / ProLogic? Do i need a receiver?
 Reply

A  Answered on 4/24/2010 by InyoPools Product Specialist Patrick P.

Yes you would need both the AQL2POD remote here and the >AQL2BASERF Base Receiver
 Reply


?     Asked on 12/18/2012by Guest

Are the batteries in the Aqua Pod wireless remote replaceable?
 Reply

A  Answered on 12/18/2012 by InyoPools Product Specialist Patrick P.

Unfortunately they are not. The rechargeable batteries inside of the Aqua Pod remote will last the average user approximately 5 years.
 Reply


?     Asked on 12/18/2012by Guest

How do I know what software version I have on my Aqualogic system?
 Reply

A  Answered on 12/18/2012 by InyoPools Product Specialist Patrick P.

To verify the software level of your Aqua Logic control and base station, press the Menu button (possibly multiple times) until “Diagnostic menu“ is displayed. Press the “>” or “<” keys (possibly multiple times) until the mainsoftware revision level is displayed (the revision should be 2.60 or higher). Next,press the “>” key (possibly multiple times) until the “RF Base” revision level is shown(the revision should be 3.00 or higher).
 Reply


?     Asked on 1/22/2013by Guest

In the product description, it says that the software needed for Hayward AQL2POD is 2.6. My remote has 1.4 software on it. Can it be upgraded?
 Reply

A  Answered on 1/22/2013 by InyoPools Product Specialist Patrick P.

The software revision on the AQL2POD remote will be different than the control box. The control box needs to have revision 2.6 or higher. The remote should work fine with your control.
 Reply


Top

Review Summary

 (Average 1  out of 5 stars)
1 Ratings
5 star:
 
(0)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(1)