Part # 4702-02
Manufacturer Code SPX0740BA
Dimensions 8" L x 8" W x 8" D
Alternate Part #'s SP740BA, SPX0740BA, SPX740BA, 27-150-2022, HAY-061-2651, HAYSPX0740BA, HPPSPX0740BA
Cover And Handle Assembly - SPX0740BA
What all does this item include? Does it include the spider gasket, cover O-ring, spring, seals, handle, pin, etc.?
Reply
This one does include everything. It has the gasket glued onto the diverter already and does have the cover o-ring. The only thing not included is the cover screws and they rarely need replacing.
Reply
Does the spx0740ba assembly replace sp0710220 part. It looks the same in picture but want to make sure
Reply
Hi William, The Key,cover, & Handle Assy (SPX0710XBA17) is the correct assembly for your model valve.
Reply
dimensions from outside to outside of the key-handle are approx. 8" the only numbers I have are on the inside stamped 43D141 and the filter sand system is S244T2, will this fit? two times I have sent back from other dealers and we have no pool service where we live. - boondocks
Reply
Hi, The 2 at the end of the S244T2 part # is very important the 2 designates that you have the 2" valve. You will require this SPX0715BA3 2" Handle Assembly
Reply
1 to 2 hrs
Screwdriver
Turned off pump, removed all screws from the assembly.
Cleaned out valve body, prepared new assembly and added a little lube to spider gasket and set new assembly in proper position. Tightened screws in proper sequence
a little at a time. Easy swap out.
Less than 1 hr
Screwdriver, Gasket lubricant
Unbolted the valve, set the screws to the side. Once it was off I cleaned the area and lubricated all gaskets, and install the new valve. Set all the screws, and tighten them in a start patter for proper seal. And bam. It was done.
The Most Helpful Review
1 0
(5 out of 5 stars) Easy to install
Reviewed By: froggy47 from San Diego, CA ()
Pros: ez install
Cons: pricy - what isn't on a pool?
I should have fixed this leak months ago. It was easy to install, unscrew 8 bolts/nuts (don't drop them & lose them) remove old top end, clean inside the shell so no grit gets on the o rings, drop in replacement (put handle 1/2 way between any 2 positions - to raise the o rings) replace 8 nuta/bolts. DONE. I made a VIDEO on the install on YouTube. Go to Froggy's Garage & search my videos using pool equipment diverter.
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) New valve
Reviewed By: Inyo Customer ()
The valve is an exact replacement, very easy to install.
Was this review helpful to you?
(5 out of 5 stars) Great Job
Reviewed By: Inyo Customer ()
Great job
Was this review helpful to you?
(5 out of 5 stars) Easy install
Reviewed By: Shannon T. from Liberty Hill, TX ()
So easy to install!
Was this review helpful to you?
(5 out of 5 stars) Great Replacement Part
Reviewed By: David from Plano, TX ()
Pros: Original part, fast shipping
Cons: None
This is an OEM part and was the perfect replacement. I came complete with the spider gasket and o-ring. Installation was a breeze. Shipping was great - arrived fast.
Was this review helpful to you?
(5 out of 5 stars) Excellent Replacment part!
Reviewed By: Larry J. from Temple,TX ()
Pros: Perfect
Cons: Non
This was exactly what I needed, replacement was very easy and a exact fit!
Was this review helpful to you?
(5 out of 5 stars) Mutli port valve
Reviewed By: Terence C. from DeBary, FL ()
Pros: Everything was great!
Cons: Tracker wasn't updated till last day and then received item, not much of a "con"!
Great price, fast service and just as expected!
Was this review helpful to you?
(4 out of 5 stars)
Reviewed By: padu ()
Pros: exact replacement for my old one
Cons: valve resevoir empties overnite
so much easier to turn than my old worn out one, but valve resevoir empty overnite with pump off, may improve with time
Was this review helpful to you?