Knob,control Assembly W/o-ring (clx200pa)

$16.99

IN STOCK

Part # 2110-08A

By Hayward Pool Products

  5 Average  

Details

Top

Part # 2110-08A

Manufacturer Code CLX200PA

Alternate Part #'s 4516073, CLX200PA

Product Description

TO INSTALL FLOW CONTROL VALVE HANDLE
1 The flow control valve handle Genuine Hayward Part (CLX200PA) is furnished in two pieces.
2 To install push the handle into the stem and fully install stem into body. You may have to remove handle and
reposition to assure the stem is fully seated.
3 Remove handle by pulling straight out.
4 Apply a single drop of Super Glue to the end of the stem, push on handle, positioned in the OFF position. Apply
pressure for 30 seconds.

Top

?     Asked on 6/28/2017 by bruce

How do you remove and replace the knob control clx2009pa
 Reply

A  Answered on 6/29/2017 by Product Owner

I have an older version but I simply had to pull it out from the chlorinator. The old one was not really easy to pull out but I eventually worked it out by twisting and turning it while pulling.
 Reply


A  Answered on 6/29/2017 by Product Owner

There is a slot in the knob almost opposite of the pointer. Place a small slotted screwdriver in the slot and gently push in while unscrewing the knob past the highest setting until it is out.
 Reply


?     Asked on 5/27/2017 by mick

how do I turn on the chlorinater
 Reply

A  Answered on 5/28/2017 by InyoPools Product Specialist Stacey M.

Hello, Once you turn on your pump water will feed through chlorinator whether offline or inline, please make sure your dial on unit is set to atleast 3.
 Reply


?     Asked on 10/19/2016 by John

How do you align the control knob assembly when you install to calibrate it with a high or low setting?
 Reply

A  Answered on 10/19/2016 by InyoPools Product Specialist Lennox H.

Hi, John. You will have to position the knob at the Off of low setting to install this knob assembly.  Instructions can be found on page 6 of the Hayward Chlorinator Manual.
 Reply


?     Asked on 7/21/2016 by Rose

The chlorinator is leaking from the adjustment knob. I would like to replace it, but I can't get the old knob off. Am I supposed to pry the handle off or screw it off?
 Reply

A  Answered on 7/23/2016 by InyoPools Product Specialist Lennox H.

Hi Rose, Some prying will be involve with removing the control knob, removal and replacing instructions can be found on page 6 of the Hayward Chlorinator Manual.
 Reply


?     Asked on 11/7/2015 by Tom Rolmans

My CL220 flow control knob has a slow leak. Believe it needs a new o ring. Does it take one or two o rings and where can I get them? I removed the knob and my unit which is more than 10 years old has one o ring.Thank you.
 Reply

A  Answered on 11/16/2015 by InyoPools Product Specialist Andy O.

Hello Tom- There are two o-rings on the knob control. I checked and they no longer sell just the two o-rings by themselves. You would have to purchase the Knob,control Assembly W/o-ring (clx200pa) part # 2110-08a.
 Reply


?     Asked on 6/9/2015 by

Our knob has a fairly large wing on one side and a small protrusion on the other side. Which part should be pointing to the number we want for chlorine use? Thanks (seems like a dumb question...last person to work on this pool didn't leave very good directions.)
 Reply

A  Answered on 6/16/2015 by InyoPools Product Specialist Lennox H.

The Control Assembly Knob that have the large wing is side that you would adjust to the number that would want your chlorinator to be set at.
 Reply


?     Asked on 5/3/2015 by Rihie nelson

My dog chewed the knob off pretty flush with housing, how does the stem itself come out. Is the stem just pressed in??
 Reply

A  Answered on 5/4/2015 by InyoPools Product Specialist Patrick P.

The stem itself is simply pressed into the Hayward CL200 chlorinator, so you may want try some needle nose pliars to see if you can pull out the broken stem.
 Reply


?     Asked on 1/10/2015 by Jeff

How do you remove the old stem and handle? Mine has a slow dripping leak.
 Reply

A  Answered on 1/12/2015 by InyoPools Product Specialist Brian M.

TO INSTALL FLOW CONTROL VALVE HANDLE 1 The flow control valve handle Genuine Hayward Part (CLX200PA) is furnished in two pieces. 2 To install push the handle into the stem and fully install stem into body. You may have to remove handle and reposition to assure the stem is fully seated. 3 Remove handle by pulling straight out. 4 Apply a single drop of Super Glue to the end of the stem, push on handle, positioned in the OFF position. Apply pressure for 30 seconds.
 Reply


Top

Review Summary

 (Average 5  out of 5 stars)
2 Rating
5 star:
 
(2)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Recent Reviews