221_750x250_top-5-reasons-to-get-a-variable-speed-pool-pump-motor_preview

5 Reasons To Get A Variable Speed Pool Pump Motor

A swimming pool pump motor is one the largest consumers of household energy. In fact, they are second only to air conditioners. A variable speed motor is a simple solution for that constantly increasing power bill. Here are 5 reasons to get a variable speed pool pump motor.

Energy Efficiency

Kicking off our top five list is energy efficiency. Variable speed (VS) motors can use 50% to 75% less energy than traditional single speed motors and get the same job done. Even though there is sufficient data and customer feedback to support that claim, there are still skeptics. Those skeptics will allege that replacing the current single speed motor with a lower HP single speed motor can produce the same savings. They are not taking into consideration the design of the variable speed motor and the Pump Affinity Law.

Most variable speed motors, like the Century V-Green, are considered permanent magnet motors. Thanks to the magnets working to spin the rotor, efficiency is improved in the VS motor. Single speed induction style motors lose efficiency because additional electricity is required to activate the magnetic field in the rotor. This means that if the same flow rate is needed, a variable speed motor will operate more efficiently and draw less power. Wait, it gets better!

Unlike single speed motors that can only operate at maximum flow rates, the variable speed motor can slow the water flow and maximize savings. To comprehend what these savings can be fully, it is important to grasp the Pump Affinity Law. This law is used to demonstrate the relationship between motor speed, flow rates, and energy consumption. Essentially, it states that the power consumption drops dramatically as the motor speed and water flow are decreased.

To better illustrate the Pump Affinity Law, we have put together a chart showing the decrease in power consumption based on RPM setting. The numbers reflect a Century V-Green 1.65 HP motor paired with a 1.65 total HP impeller.

Durability

Variable speed motors are totally enclosed and fan cooled. The enclosed design protects the internal components of the variable speed motors from environmental elements. On the other hand, single and dual speed motors are standard induction motors. Vents on the induction motors can allow water, and sometimes critters, to enter and cause damage.

Furthermore, because the variable speed motors run at lower speeds and because they are fan cooled, the motors stay much cooler. This will aid in preserving the bearings and motor windings. Ultimately, these design differences allow the variable speed motor to have a longer life.

Easy Installation & Programming

Installation of the variable speed motor is the same as a single speed motor. All of the original pump components can be transferred to the VS motor. This excludes the pump seals which should always be replaced when a new motor is installed. The wiring from a single speed motor is also transferable. The same three lines that were used for the single speed motor can be used to supply electricity to the VS motor.

Once the motor is installed, it needs to be programmed. Since every pool is different, the programming is not standard. The speed settings will have to be dialed in according with the equipment’s requirements. This will require experimenting with running the motor on different speeds. Once the minimum operating speeds have been determined for each piece of equipment, the run times can be set.  

Keep in mind that the items like automatic cleaners and water features do not need to run the entire time the pump is on. It is normal to have those items running only an hour or two a day. A low RPM can be used to circulate the water the rest of the time. As stated before, running the motor on lower speeds generates the greatest savings.

Additional Resources – Poolside Repair: How to Install an Energy Efficient Motor

Remote Monitoring

Until recently, the ability to monitor the pool system remotely required an elaborate control system. Century V-Green variable speed pump motors now have wireless capability when combined with the VLink interface. Once the VLink is connected to the home’s wireless network, the pump can be controlled from any smart mobile device.

Pool owners can program, monitor and adjust settings anytime, anywhere. Plus, the VLink app displays the live energy consumption and delivers the exact operating cost.   

Quiet Operation

Concluding our top 5 reasons to get a variable speed motor is noise or a lack thereof. As mentioned before, VS motors are totally enclosed. This means that most of the noise generated is muffled instead of being released through vents like the induction-style motors. While operating at a low speed, it’s hard to tell if the motor is running. Actually, the variable speed motors running at a high speed are noticeably quieter than traditional single speed motors.

 

17 thoughts on “5 Reasons To Get A Variable Speed Pool Pump Motor

  1. Foaming problem, caused by algaecide in the spring, looked very bad with company coming over. Turned off pump and got the garden hose with good nozzle and made something like a heavy rain which got rid of the foam in minutes. Looked good for the event. Very short term fix!!

  2. My power bill dropped significantly and I was still able to skim day and night for the most part (I think that the schedule shut it down for a few hours at some point in the day but overall very pleased!

    1. Hi, Can you tell me what schedule your previous pump ran? Ex: 1 hp 8 hrs a day…
      Compared to this new pump? How many hours and what speeds did you set up?

      I am interested in this motor but skeptical of the actual energy savings. Can you tell me a more accurate savings your had? Thanks for the info!

  3. I purchased a variable speed pump to make the savings in electricity as suggested. However I found that as the pump speed decreased so did the EFFECTIVE flow rate disproportionately. By extrapolating on a graph I found that zero flow rate occurred at 600 rpm. In other words I needed 601 rpm to make the water overcome the inertia in my pool system. At 3200 rpm the rate was 38 gallons per minute but at half speed it fell not to 19 gpm but 7 gpm. The wattage may have reduced as per your chart but so did the gpm in a near identical manner. The most important piece of information that a user wants to know is how many gallons per minute the pump is producing on his/her installation at each speed setting so as to calculate the number of times the water in the pool turns over. Secondly is wattage, so as to determine electricity consumption. Rpm is almost unnecessary. No pump gives the gpm (except, I believe, the latest Pentair Intelliflo).

    1. Thanks for sharing your thoughts, Chris. The Pentair Intelliflo VF will display the current GPM. We recommend adding a flow gauge if you have a model that does not display the GPM. As far as wattage, most new variable speed pumps/motors will display the wattage consumption.

    2. its a basic law of physics. energy in = energy out. x amount of gallons of water per second can be converted to pounds of water, and pressure can be converted to feet of head. 550 ft-lb per second = 1 horsepower and 1 horsepower= 746 watts. the reason a variable speed motor uses less power at lower RPM, and disproportionately to RPM is that the flow rate in GPM of a centrifugal pump is also disproportionate. the lower flow rate is likely fine to run through the sand filter and keep the pool clean. with a single speed motor there is nothing but full on or full off without expensive drives and properly rated motors so your choice to save money is a timer, and hours with 0 flow.

  4. My pool is 16′ X 32′. What are the purchase prices for VS pumps to service my pool? And where in the London Ontario region would I find a dealer?

    1. If you are only replacing the motor, we would match the replacement variable speed to your current motor’s frame and total HP. Do you know the part, model, or catalog number that is listed on the motor’s label?

  5. At the high rpm’s everything is good, but once it drops down, I get air bubbles and lose prime. Is this common?

    1. Hello Ginah – You’ll have to test the RPM settings on the pump to see what is required to move the Polaris. Once you figure that out, you can program the pump to run in that RPM for a particular time each day.

Leave a Reply to Gerry Cancel reply

Your email address will not be published.