Part # GOKIT32
Alternate Part #'s 65032, GO KIT 32, PL1032, AEQGOKIT32, APCK1027
Standard tune up kit for the Pentair / Purex Whisperflo pump includes the shaft seal and all o-rings, gaskets and lubricant.
We highly recommend replacing the shaft seal, o-rings and gaskets when replacing your motor. If you use your old shaft seal, it will not mate up properly with the new motor and may leak.
This Tune Up Kit Works on These Pumps:
Tune Up Kit Includes:
For More Pool Pump Motors
Click Here For Saltwater Pool Tune Up Kit (GOKIT32SALT)
Will ths kit work on a superflow? looking at at a B2854 motor. My pump is a 355024s, 56y. 115/230
Reply
Hello John. The Pentair Whisperflo GOKIT32 is not compatible with the Pentair SuperFlo. The GOKIT78 contains the correct tune-up parts for the Pentair SuperFlo. GOKIT78 Attached please find a Pentair SuperFlo exploded parts diagram for reference. Pentair SuperFlo Pump A GOKIT is specific to the manufacturer/model of the pump, not the motor.
Reply
Is this tune up kit good for a WhisperFlo model # WFE-3?
Thank you for contacting Inyo Pools, Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 is the correct tune up kit. If you have saltwater Tune Up Kit Pentair/Purex Whisperflo Saltwater - GOKIT32SALT is the correct tune up kit
Reply
Hello. I need a bearing kit for a Century Centurion (A O Smith) serial: BY01-27 Part 7 186236-20 1081 3/4 hp pool pump motor and gaskets for a FOXX Ultra Flow model #: 38448222
Hello Bill. The bearings for the Century Centurion motor 7-186236-20 are the Century motors Bearing, 203 (2 required): Bearing, 203 (Single) - 62032RS. The Aladin Tune-Up Kit - GOKIT20 contains all the replacement gaskets/o-rings for the Foxxx UltraFlow pool pump. Tune Up Kit American Ultra Flow & Bronze Pump - GOKIT20
Reply
Is this the correct tune up kit for the whisper flow 355022S motor. I want to make sure before I add it to my order.
Reply
Yes this is the correct tune-up kit for your whisper flow 355022S motor.
Reply
I have a WhisperFlow High Perfomance Pump Purex Pool Equipment,
Mode# WFE-4, 1HP, Serial# 0492105 and it developed a leak which I think might be the seal and I don't want to tear it a part until I have all the parts in hand
to repair. I would like to know which tune up kit I would need to purchase for that particular pump.
Hi Ronald, You will require this GOKIT32 Whisperflo Tune Up Kit
Reply
My century centurian 2.5 HP CAT B2840 TYPE CX with a 56Y FRAME is leaking whats the correct seal replacement kit
Reply
Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
What is the correct replacement motor for a WFDS-28 Motor #177456 2.0/.25 FR Y56Y
Reply
Hi Joe, the direct motor replacement for your motor part number 177456 is catalog number B983, and this is the correct seal kit in a standard chorine swimming pool. For a saltwater pool, it will be the GIKIT32SALT.
Reply
Just making sure this is the right kit, thanks in advance!
Hi Jeffery, yes this is the correct seal kit for the Pentair Whisperflo model WFE-28 pool pump. If you have a saltwater swimming pool you can also use the GOKIT32SALT.
Reply
Is your GOKIT32 the proper one for my Pentair WF-28 (pn 11774) pump? I need to replace the seal. Thanks.
Reply
Hi Jerry, yes this GOKIT32 is the correct seal kit for the Pentair Whisperflo model WF-28. For a saltwater swimming pool, we recommend the GOKIT32SALT as it has a more corrosion-resistant shaft seal.
Reply
I would like to replace the motor on my whisperflo WF-28 2HP pump and would like to know which go kit and which motor to order.
Thank you!
The replacement motor for your motor part number 177476 is the B859 that you can view by clicking here. This seal kit is correct for your Pentair Whisperflo saltwater pool and the GOKIT32 that you can view by clicking here is for a standard chlorine pool.
Reply
I have a Purex Whisperflow pump 1-1/2 HP connected to a Purex SMBW2060 Filter for my 20,000 gal inground pool. It's over 20 years old and I can hear air leaks when running. I would like to rebuild it. Cannot read the p/n on pump. which rebuild kit should I order?
Reply
Hi Dave, this is the correct tune-up kit for the model Pentair Whisperflo series pool pump.
Reply
Hello,
I have a Pentair 340039 (photos attached) where the coil in the motor inexplicably burned to ash. I need a replacement motor (355022S ?) and the seal kit - is this the correct one? Thank you!
Hi Victoria, This is NOT the correct seal kit for the pump in your photos. You will require this Pentair Super Flo Seal Kit and this 1.5 HP Up Rate Super Flo Replacement Motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
We have a Pentair 7-177475-20 y56y pump and we are replacing the motor with the Century 1.5 HP square flange 56y Up Rate motor - B2854 but we don't know what gasket kit goes with it to replace them when we change out the motor or would you recommend a different motor?
Reply
Jason, The seals are specific to the pump housing, not the motor. If you can provide the model number from the pump housing, we can recommend the correct seals.
Reply
I am replacing a 071314s motor with a B2982 motor. My pump is model WFE-4 and it is a chlorine pool. I would like to replace all of the seals as well. Can you tell me the correct tune up kit?
Reply
Hi David, The Tune Up Kit on this Page GOKIT32 would be the proper seal kit for your WFE-4 Whisperflo Pump.
Reply
Hello there
Will this kit work for my pump? SN: BY12-08 Part: 7-177452-03 type: CX FR: Y56Y
Need your confirmation before to order. Also what new motor would you suggested to replace it?
Thank you
Hi Matthew, Yes this is the correct Tune-Up Kit for your Whisperflo Pump included in your photo. Please click here for the B2843 Replacement Motor which is the proper replacement motor for your pump in the photo. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Thank you for your quick response, can I have the link for the bearing too (front and back) so I added to the cart to make one order.
Reply
Hi Matthew, The front and back bearing for your motor are the same and it is this 6203 Pool Motor Bearing, you will require 2 of these one for the front and one for the back. I hope this helps, if you have any questions please let us know.
Reply
Hi, I ordered a Century B2854 motor and a Hayward pump SP 2810x15. What is the correct GoKit, ?
Thanks,
Siggi
Reply
My Pentair 177450-03 Is noisy, and losing pressure. It also leaks (slowly) and does feel hot. Will this kit possibly cure this, or do I need a replacement motor and this kit? Thanks
Reply
will this kit work on a model HSQ165 motor
Reply
Do you have information on the front half of your pump? The best place to find your pump model information is on the pump housing tag. Pool pump manufacturers label each housing with make and model information as well as serial numbers. The pump model number is the golden ticket to finding the proper tune up kit, so we will want to find that most of all. The tag is usually placed on the side of the strainer basket or near the discharge port for easy access. Model number formats vary depending on the manufacturer but should be marked clearly.
Reply
Hi, I have a pentair wf 28 2hp 115/230v ,need to replace motor,
what motor do I need and what gasket kit do i need?
Thank you
Reply
Hi. You will need the PL2859 and this Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
Hi, I have a pentair wf 28 2hp 115/230v ,need to replace motor,
what motor do I need and what gasket kit do i need?
Thank you
Reply
Hi. You will need the PL2859 and this Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
is this the right kit for motor b2853?
Reply
Hello, What is the brand and the model of the entire pump? If you are unsure, you can send us a side photo of the entire pump and we can identify it for you.
Reply
How do I get a performance curve for a Whisperflo WF-26 using this Motor?
Reply
Hi. You can use this Whisperflo Performance Curve to gather the flow rate if you know the Total Dynamic Head (TDH) of your pool.
Reply
That curve is for only one speed. I need a curve showing multiple speeds.
Reply
Hi, Michael. The Whisperflo Performance Curve is also used for the single and dual speed Whisperflo Pumps.
Reply
Will this fit the 1/2 HP Standard Motor - Full Rate (B846, B2846)?
Thanks
Reply
The seal kit will depend on the model number or name of the front pump housing that the motors bolt to. If you click here then you can view a pump that uses this seal kit. If you are not sure of your model then you can always email images of it to upload@inyopools.com so we can assist.
Reply
whisper flow motor replaced by century motor cat #B855 which seal kt do I use?
Reply
Hi. This Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT is the correct kit you'll need.
Reply
whats the difference between go kit 32 and go kit 30 and which one fits a purex WFE-8
Reply
I have a pentair intelliflo pump WF/NT - 4 - 160 P/N 011013. I need a new impeller as the short 2 1/4" moulding that sticks out from the pump sheared off (side where the screw goes in) Will i also need a housing.
Reply
The impeller is listed as key 17 on this Intelliflo parts diagram. We do recommend replacing any apparent pump parts that are worn or damaged but if would like us to be sure then please send a few images of the pump and its damaged or worn parts to upload@inyopools.com.
Reply
What's the difference between the GOKIT32 and the GOKIT5? I am purchasing a Pentair Challenger 1.5HP Full Rated (B2842) Motor and want the correct seal kit.
Reply
Hi, David. The GOKIT32 is for a Whisperflo Pump and GOKIT5 is for a Challenger Pump (High Pressure). The B2842 is the motor number which can be used on several different pumps. If you can provide us with the model number of the Challenger pump that you have we can confirm if GOKIT5 is the correct kit.
Reply
My pool was built in 2002 still have the same pump. Recently I had the motor replaced on the pump Pentair Challenger High Performance pump and it has started to leak. The motor is a Century cat#B2854 pt#0-F56AA40A01-24. What tune up kit do I need to order? Thanks in advance Juan T
Reply
Hello Juan- The tune up kit you will need for your Pentair Challenger is the Tune Up Kit Pentair Challenger Pump - GOKIT5
Reply
I ordered 3/4 hp square flange motor. Is this the kit for the motor shaft and pump impeller?
Reply
Hello Waylon- The seals are based off of the pump not the motor. We would need to know what the model of your pump is to find the right seals for you.
Reply
I have a Whisperflo WF-24 pump with an AO Smith B2853 motor. Is the GO KIT 32 the correct kit to replace the seals?
Thanks in advance,
Alan
Reply
The GOKIT32 is the correct Tune-up Kit for the WhisperFlo WF-24. Reminder that if you have a salt water chlorination system, yoou will want the GOKIT32SALT Tune-up kit.
Reply
I have a whisper flow pump, Can i just change the motor to a variable speed to make it more efficient or do i have to change the whole pump ?
Reply
Hi Rob, Yes, you can convert your Whisperflo Pump to a variable speed pump using the Century V-Green Motor.
Reply
I have a Whisper Flow unit. The place where you add water before turning on the pump. The part 357150 has two ridges broken so I cannot tighten the lid. Every thing works but this tightening device. Can I purchase such part to align and secure the lid.
Thank you
jim14mayfield@gmail.com pump
Reply
Hello Jim, Yes the Lock Ring - Black (whisperflo) (357150) is available for purchase and you can click on the link to take you to the product page.
Reply
I think I found the right replacement motor for the Pentair Super Flo High Performance Pump (Motor # 196237) Part # 340037 Model SF N1-3/4A
It's the Century B2847. 56Y. What tune up kit do I use since you don't list Super Flo only Whisper Flo ? Please let me know if I have the right Motor, Also is there an EE model for better efficiency.
Reply
The energy efficient replacement is part number B661 and the seals that I'll need are part numbers 5003-04 and 5250-104. If you need any other parts here's a link to the parts diagram.
Reply
I have a Pentair WF-26 , 011773 pump. The intake valve was left closed from a cleaning and the pump ran 8 hours dry. The pump works but seems like it is making a lot more noise. Is it likely that the pump was damaged and if so, any recommendations on parts that would be needed to rebuild the pump? I did not find a new pump without the motor as a part on the web site. Is that available and if so, how much?
Thanks
Reply
Hi Steve, many times when this happens the motor can get extremely hot actually warping the pump housing and damaging the motor. My suggestion would be a complete new Pentair Whisperflo WF-26 011773 Pump. You could keep your old pump for spare parts if you ever needed them.
Reply
I have an older Wisperflo Pool Pump and need to replace the motor and all gaskets.
Do you have a GOKIT32-SALT gasket set for salt water pools?
Reply
Hi, Click the link >Pentair/Purex Whisperflo Tune Up Kit (GOKIT32SALT)<, it will direct you to the kit for salt water pools.
Reply
Why doesn't this kit come with bearings?
Reply
Alex, The GOKIT32 is specifically made for the "wet-end" of the pump not the motor. The bearings are specific to the motor not just the pump model. We can try to match the bearing based on the model number or the size of the bearings.
Reply
My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
Reply
The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
Reply
I just finished replacing the shaft seal on my booster pump. As soon as I turned the pump on water was leaking from the shaft seal. Is it defective or am I doing something wrong?
Reply
Depending on the model, the installation of a booster pump shaft seal can be slightly different than a pool pump shaft seal. Some booster pump and pool pump shaft seals require that a silicone sealant be used on the outer areas of the metal seat of the shaft seal. The seal will need to be lightly hammered into the body of the pump. You can use a 1 inch PVC coupling or a piece of 1 1/4 inch PVC pipe and a rubber mallet. This procedure will apply to any pool pump or booster pump using a >PS-1000 style shaft seal.
Reply
I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!
Reply
You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.
Reply
2 to 4 hrs
Screwdriver, Nut Drivers, Socket Set, Adjustable Wrench
2 to 4 hrs
Screwdriver, Socket Set, Wrench Set
2 to 4 hrs
Screwdriver, Pliers, Socket Set, Wrench Set, 3/4 inch PVC pipe
2 0
I did some troubleshooting based on watching the excellent videos on inyopools.com and determined that the motor bearings were bad. I called Inyo and they were able to find the correct bearings for me very quickly.
The associate also suggested that since I will be removing the motor to do the repair I should get the tun up kit and do a tun up. I did get this tun up kit and replaced all the gaskets and seals. I didn't have the correct tools for installation of seals but managed to get it installed using PVC pipe. I saw the instruction of doing that on Youtube. It all worked well and the pump is running very well now.
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set
1 0
See other descriptions
Power off
Ensure power off
Caveats: after removal of the motor rear cover to expose wiring: picture wire hook up w your phone.
The shaft seal is pressure fit into the housing mount plate. I agree with removal w motor attached. This allows removal of volute and impeller. Then motor can be removed.
Caveat: carefully tap the old shaft spring and seal out of the mounting plate. The new spring seal unit must now be press fit. Look in your socket set and select a socket that matches the diameter of this seal cup.
I placed Teflon lube around the outer cup of the seal/ spring unit. Then line up w the plastic motor plate receptacle. The socket you just measure matched is now placed over the spring/seal assy.
Keeping level and over the plate receptacle, tap in with a small hammer. This applies pressure evenly to press-fit flush into the plate. The Teflon lube should be used on all seals.
Keep seals in their respective grooves and avoid twisting. Reassemble in reverse order. Power up and check for leaks.
Leaks are due to:
Seal got out of groove
Seal got twisted
Didn’t use lube
Not tight enough
Over tightened and cracked plate or housing
That little motor support is essential to keep the motor level. A cracked plate, or worn seal may occur without it over time.
2 to 4 hrs
Screwdriver, Socket Set, Wrench Set
0 1
After removing motor replaced all o-rings and seals reinstalled motor. Note should use a 1inch pvc coupler and some silicone when replacing spring seal in pump housing. Had remove motor twice because I had a small leak.
1 to 2 hrs
Screwdriver, Wrench Set, Adjustable Wrench
3 0
Every so often, I undertake the task of rebuilding my pool pump and motor myself. Every few years, the front and/or rear bearings go out on the motor. When this happens, I take the motor apart, clean up the armature and stator, drive old bearings off and drive new bearings on the armature. after the motor is reassembled, I then take the pump apart and check the impeller, as well as all other parts in the pump. I ALWAYS reassemble the pump with a new ceramic seal, as well as all rubber parts - "O" rings and gaskets. In this fashion I am guaranteed a great repair with no need to repeat the task.
1 to 2 hrs
Screwdriver, Pliers
1 0
1 to 2 hrs
Socket Set, Wrench Set
4 0
After turning off all power to my pool equipment at the main, I started by draining all the water out of my pump volute. I next used a socket and ratchet to loosen the six (6) bolts from the seal plate to the volute.
Next, I removed the Seal plate, still attached to the motor, from the Volute. Next, I replaced the rubber gasket for the seal plate as well as the o-ring on the diffuser.
I was now ready to reassemble the pump. I used a little lube to hold the gasket in place as I moved it back into the volute. Once I had a good seat, I started inserting the bolts, being careful just to hand tighten all six. Then I went around and tightened the bolts carefully with a wrench, alternating from top-right to left middle to bottom right and so on to create an even tightening on the gasket.
When I was all done, I switched on the electrical, primed the pump and everything worked great.
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set, Hex key for diffuser set screws
After receiving parts and ensuring fit, I started the replacement.
Watched INYO video on how to replace motor and replace seals
Turned off power to pump
Removed motor
Removed old seals, including all old silicone sealant. Cleaned all old parts THOROUGHLY.
Used new latex gloves to keep all seals and gaskets printing during installation.
Installed shaft seal on new motor
Installed new pump gasket
I n stalled new motor into pump
Connected power to motor
Confirmed all connections visibly
Restored power to breakers
Started pump
Checked for leaks
The Most Helpful Review
6 0
(4 out of 5 stars) All the seals needed in one package
Reviewed By: MadSea from Jacksonville , FL ()
Pros: direct replacement - all the parts needed
Cons: No "Don Not Lube" Warning
Didn't know NOT TO LUBE the ceramic disk as there is no warning on the Go-Kit. I luckly had some troubles on installing the impeller and refered to Inyo's great online help, where I learned about the oil contamination issue and got mine cleaned up before going into service. The "D" shaped O-ring was a PITA to install, but eventually got it my filing the grove on the plate so the ring would seat better. I used the lube to help keep the ring in place as I seated the ring into the groove... a 30 minute job alone.
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Great for rebuilding your pump when changing motors.
Reviewed By: Inyo Customer ()
I purchased the Gokit for use with a V-Green upgrade to replace my single speed pool pump motor. Everything was included, even the silicone lube.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
This saved my son a ton of money by doing it himself.
Was this review helpful to you?
(5 out of 5 stars) Pentagram tune up kit
Reviewed By: Inyo Customer ()
Perfect
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Worked with us via email photos to make sure correct kit was ordered
Was this review helpful to you?
(5 out of 5 stars) All gaskets necessary for a pump motor exchange
Reviewed By: Inyo Customer ()
I bought this kit in combination with the 3/4 Hp square flange 56Y EE motor. Everything was included in the kit (some additional gaskets were included, but I couldn't find a use for them)
Was this review helpful to you?
1 0
(5 out of 5 stars) All Good
Reviewed By: Inyo Customer ()
They send you extras but once you figure out you do not need everything in this set to replace your motor - then you are all good.
Was this review helpful to you?
(5 out of 5 stars) Perfect set of seals.
Reviewed By: Inyo Customer ()
Perfect set of seals to replace old pool pump motor.
Was this review helpful to you?