AG Thru Wall Pool Light - NA4035



Model # NA4035

By Ocean Blue

  5 Average  



Model # NA4035

Product Description


Add instant light and color to your above ground pool at a fraction of the cost of similar lights. Simply install into your pool?s existing return fitting in less than 10 minutes. No holes to cut or reseal.? No obstruction for return line water flow.?Directional flow water jet insures proper water filtration. Includes an extension fitting to accommodate either a wall fountain or a pressure side cleaner.
Add the red, blue or green lens (included) to bring a splash of color to your pool. 8 super bright LED lights will last over 100,000 hours and are 80% more efficient than standard lights.

No hard wiring needed as light plugs into standard 110V GFCI outlet. Comes with a 25 cord and 12 volt weather-tight sealed transformer with on/off switch. Quick disconnect design makes winterizing a breeze. UL/CA listed.

LED Thru Wall


?     Asked on 5/24/2018 by

Can the return port on this light be adjusted for direction of flow or does it only point straight out?

A     Answered on 5/25/2018 by InyoPools Product Specialist Lennox H.

Hi. Unfortunately, the eyeball cannot be adjusted.

?     Asked on 7/18/2017 by Jennifer

Would this light fit the Morada 6, 24 foot existing light? Where can I order just the bulb?

A     Answered on 7/18/2017 by InyoPools Product Specialist Alex V.

Jennifer, Yes this will fit the Morada pool. Unfortunately, we do not have just the bulb. 

?     Asked on 7/17/2017 by greg

My pool wall is 3/4 thick will this light work ?

A     Answered on 7/18/2017 by InyoPools Product Specialist Lennox H.

Hi, Greg. This light will not be able to be properly installed in a 3/4" pool wall. 

?     Asked on 5/15/2017 by Jane Anne Bray

Half of my lights have stopped working after a year I notice some water inside where the lights are. How can I take it apart to change lights and let the water out

A     Answered on 5/19/2017 by InyoPools Product Specialist Lennox H.

Hi, Jane. Unfortunately, this light can not be repaired you will have to replace the entire unit.

?     Asked on 4/1/2017 by Bob

My light is fine and I love it but the PVC fitting broke where can I get a replacement

A     Answered on 4/5/2017 by InyoPools Product Specialist Lennox H.

Hi, Bob. Replacement parts are not available for this light.

?     Asked on 6/8/2015 by

what are the id/od dimensions for an exsisting hole in my pool liner and wall. After 20 years,a critter chuded thru my electrical wire and the gaskets warped, in te same spring. i dont need anything to bright . light draws bugs. Have you got any help.

A     Answered on 6/16/2015 by InyoPools Product Specialist Lennox H.

AG Thru Wall Pool Light is installed to the return jet of your pool. That opening is about 2-1/2" wide with the wall fitting.

?     Asked on 5/30/2015 by

Can this also be used in an In ground pool return?

A     Answered on 5/31/2015 by InyoPools Product Specialist Matt S.

Hello, This light is only for above ground pools because of the restrictions the light cord and installation requirements. Review the NA405 Owner's Manual for installation requirements

?     Asked on 5/29/2015 by armando

How many volts?

A     Answered on 5/30/2015 by InyoPools Product Specialist Patrick P.

This light would plug into a 120V outlet there is a transformer so the 120V is dropped to 12V at the pool light fixture for safety.


Review Summary

  (Average 5 out of 5 stars)
1 Ratings
5 star:
4 star:
3 star:
2 star:
1 star: