Details

Top

Model # PL9846

Warranty 1 Year

Product Description

Hit the right note with this Waterfall light Accent

Our Lighted Waterfalls are the latest in LED Pool Water features. The LED strip is built into the unit placing the light as close to the water as possible. Our design makes a separate light source unnecessary.

Specs:

  • 12 Volts
  • 1.5” spigot plumbing
  • 1 GPM per inch
  • 6” lip (cannot be cut)
  • 100 feet of 12 volt cord is included
  • Light shows: fade from one color to the next, strobe and fixed colors
  • Light control through a Remote Control
  • One waterfall remote kit which is required and sold separately can control up to a combination of 20 feet of waterfalls.

Note: One Waterfall Remote Kit is required to power our LED Pool Waterfalls. One remote kit will power any combination of our LED Pool Waterfalls up to 20 feet of combined width. The components of the waterfall remote kit are shown below.





Product Specifications

Lip:
6 in.
Color:
White
Width:
48 in.
Top

?     Asked on 7/5/2019 by Ohad

I would like to know what is the best height to put this water full from the edge of the pool?
 Reply

A  Answered on 7/5/2019 by InyoPools Product Specialist Lennox H.

Hi, Ohad. The max installation height is 4 feet. 
 Reply


?     Asked on 1/10/2019 by Andre

I WANT TO PUT MY WATERFALL ELEMENT AT THE EDGE OF THE POOL WHAT IS THE RECOMMENDED DISTANCE FOR INSTALLATION FROM POOL EDGE . IT WILL BE INSTALL 6'-00" FROM POOL DECK LEVEL
 Reply

A  Answered on 1/11/2019 by InyoPools Product Specialist Lennox H.

Hi, Andre. The wall depth will have to be 10"-12" in order to house this waterfall. 
 Reply


?     Asked on 3/19/2018 by

I have a new pool being constructed and have a 2" stub out for a water feature. Please decsribe how I would install this in newly constructed cinder block wall with regard to plumbing and electrical.
 Reply

A  Answered on 3/23/2018 by InyoPools Product Specialist Alex V.

Laurie, There are some photo examples of that in the owner's manual (starting at section 3.1.1). Please note that the lip must be supported as shown in the illustrations. 
 Reply


?     Asked on 4/12/2017 by

My pool plan shows separate drains for the waterfall in the pool, but I do have not seen the requirement for drains in any of the installation guides. Do I need to add drains just because I am using a waterfall? Or will my two main pool floor drains and skimmer be sufficient (seems so to me)?
 Reply

A  Answered on 4/13/2017 by InyoPools Product Specialist Scott W.

Your current drains will be sufficient enough for your waterfall, no need to add an additional drain.
 Reply


?     Asked on 4/12/2017 by

What else do I need to buy to make this waterfall with LED light work properly (in addition to the LED remote controller described in the manual? What size pump do I need (the waterfall will be 3' above the water line of the pool)? Do I need to buy a secondary filter (in addition to the main filter for the pool)?
 Reply

A  Answered on 4/12/2017 by InyoPools Product Specialist Scott W.

No you do not need to have a second filter and you maybe not to get a second pump for the waterfall. What is the distance for your current pump to where the waterfall is going to be.
 Reply


?     Asked on 12/9/2016 by Mark

Hello. Which side is the standard placement for electrical wires for led strip? If I am facing the rear of the waterfall, is the standard electrical placement left or right? I am hoping you say left. Thx!
 Reply

A  Answered on 12/9/2016 by InyoPools Product Specialist Lennox H.

Hi, Mark. The Brillant Wonders Waterfall is capable of accommodating the electrical conduit on either side.
 Reply


Top

Review Summary

 (Average 0  out of 5 stars)
0 Rating
5 star:
 
(0)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)