Saltwater Tune Up Kit Hayward Super Pump - GOKIT3SALT

$47.95

IN STOCK
FREE SHIPPING

Part # GOKIT3SALT

  4.75 Average  

Details

Top

Part # GOKIT3SALT

Alternate Part #'s PL1083

Product Description

Tune up kit for the Hayward Super pump when used with a salt chlorine generator.  The heavy duty parts in this kit are designed to withstand exposure to salt.

We highly recommend replacing the shaft seal, o-rings and gaskets when replacing your motor.  If you use your old shaft seal, it will not mate up properly with the new motor and may leak.  Our tune up kits include the shaft seal and all o-rings, gaskets and lubricant for your pump.

This Tune Up Kit Works on These Pumps:

  • All Hayward Super Pumps 1/2 HP - 3 HP single and dual speed models.
  • All Hayward SP2600 Series Pumps
  • Works on both standard efficiency and energy efficient Hayward Super pumps
  • Note: Hayward Super II Pumps use GOKIT2SALT

Tune Up Kit Includes:

  • Motor Shaft Seal For Saltwater Pools
  • Diffuser Gasket
  • Pump Lid O-Ring
  • Housing Gasket
  • Lubricant

For More Pool Pump Motors

Top

?     Asked on 6/10/2019 by Aj

Is this the kit I need for SP 1620z2bc if so does the kit come with a new bearing I believe me is bad. The pump is really loud
 Reply

A  Answered on 6/10/2019 by InyoPools Product Specialist Patrick P.

Hi Aj, Could you let us know if your pump is a Hayward Super Pump, Hayward Super II, Hayward Northstar, Hayward Tri Star or Hayward Max Flo? This kit does not come with bearings. 
 Reply


?     Asked on 5/19/2019 by Kasi

Purchased the replacement mortor 1 HP Round Flange 56J Up Rate Motor - B228SE, can you advise me on which seal, O Ring set I need to purchase. Thank you,
 Reply

A  Answered on 5/19/2019 by InyoPools Product Specialist Patrick P.

Hi Kasi, Could you send us a few photos of your pump? We would need a wide shot showing the complete pump including where the pipes go in and out of your pump. Simply click on the reply link below to upload your photos.
 Reply

  • Commented on 5/19/2019 by Product Owner

    Hope these will work for you

     Reply

    • Commented on 5/19/2019 by InyoPools Product Specialist Patrick P.

      Hi Kasi the Hayward Super Pump Tune Up Kit on this page is the correct tune up kit you will need for your pump in the photos.
       Reply

      • Commented on 5/20/2019 by Product Owner

        Thank you Very Much!!
         Reply

        • Commented on 5/20/2019 by InyoPools Product Specialist Patrick P.

          You're Welcome Kasi!
           Reply


?     Asked on 10/27/2018 by Darwin Clemens

I have a Sp2602vp Variablespeed 1 1/2 HP pump. What gasket kit should I use for salt water?
 Reply

A  Answered on 10/30/2018 by InyoPools Product Specialist Hector F.

This is the correct saltwater seal kit for the Hayward Super Pump VSP pool pump. 
 Reply


?     Asked on 10/12/2018 by Richard E Faulds

WHAT IS THE DIFFERENCE BETWEEN THE GO KIT 3 SALT AND REGULAR GASKET KIT? I TRIED REPLACING SHAFT SEAL AND BEARING BUT STILL HIDEOUS WHINING AND PUMP NOT WORKING ADEQUATELY. CAN I USE TUNE UP KIT RECENTLY PURCHASED?
 Reply

A  Answered on 10/12/2018 by InyoPools Product Specialist Lennox H.

Hi, Richard. The Pump Shaft Seal that is in the saltwater kit is made with a viton material. The tune up kit is used to prevent leaks from the pump. 
 Reply


?     Asked on 8/21/2018 by MARCO

GOOD AFTERNOON IS THE UST1152 AND THE GOKIT3 SALT IS THE CORRECT PARTS FOR HAYWARD SUPER PUMP C48L2N134B1
 Reply

A  Answered on 8/22/2018 by InyoPools Product Specialist Hector F.

Yes, the UST1152 would be the correct motor and the GOKIT3 is also correct for a saltwater pool with a Hayward Super Pump. 
 Reply


?     Asked on 7/22/2018 by dale campos

I have a question regarding replacement motors. I keep hearing people say you have to buy go-kits when replacing motor. I understand that you should replace the housing gasket and impeller seal. But i find it very HARD to believe you would have to replace the shaft seal. If the replacement motor is brand NEW why in the world would you replace the shat seal on a new motor. ????????
 Reply

A  Answered on 7/23/2018 by InyoPools Product Specialist Hector F.

The shaft seal is the most important seal to replace because it is the seal that keeps the water from making contact with the face of the electrical motor. If that seal is bad it can cause the motor bearings to fail and the motor to go bad prematurely to the average lifespan of the motor. 
 Reply


?     Asked on 6/23/2018 by JT

I bought the UCT1102 a couple of years back and it has worked fine but this year it is buzzing, still pumping water but I also see a leak from underneath which sounds like a bad shaft seal so I presume I need to install another Saltwater tuneup kit. What about a bearing as well? Is that was is causing the buzzing? Thanks.
 Reply

A  Answered on 6/27/2018 by InyoPools Product Specialist Hector F.

Loud noises coming from the pump are usually the motor bearings and if you see leaking then ideally a new seal kit or shaft seal may need to be replaced. These are the most common causes and resolutions for what you are describing but may need a further inspection to confirm. 
 Reply


?     Asked on 6/10/2018 by ray schrecker

how do you disassemble the pump motor form the pump
 Reply

A  Answered on 6/10/2018 by InyoPools Product Specialist Lennox H.

Hi, Ray. You can check out Inyo's How To Replace the Motor on Your Pool Pump guide for instructions.
 Reply


?     Asked on 5/29/2018 by jason miller

Is this the same kit for SP1607z1mbk Hayward super pump.
 Reply

A  Answered on 5/30/2018 by InyoPools Product Specialist Patrick P.

Yes this is the correct kit for the SP1607z1mbk Hayward super pump.
 Reply


?     Asked on 4/16/2018 by

Hello I have Hayward UST1152 with salt water. What go kit do I need? Thank you.
 Reply

A  Answered on 4/17/2018 by InyoPools Product Specialist Lennox H.

Hi. I would need the manufacturer and model of the pump housing in order to locate the seals and or available kit.
 Reply


?     Asked on 4/8/2018 by Jay

Hello, I have the Hayward SP2615X20. Is this kit compatible with my pump?
 Reply

A  Answered on 4/9/2018 by InyoPools Product Specialist Hector F.

Yes this is the correct seal kit for the Super pump with a salt water pool. 
 Reply


?     Asked on 11/19/2017 by John

I have a UST1152, model C48L2N134C1. It is still moving water but is making terrible noises. I'm looking to replace it. What is the difference on the UCT1152 and UST1152? What else do I need?
 Reply

A  Answered on 11/20/2017 by InyoPools Product Specialist Hector F.

The UCT1152 is an energy efficient model drawing slightly less amperage. Also, it is recommended to replace the seals and gaskets. In order to cross-reference which seals that you would need, we would need to know the model name or number of the front pump housing that the motor bolts to. If you do not have that information then you can send us images of that housing to upload@inyopools.com
 Reply


?     Asked on 9/1/2017 by Collin

What Saltwater Tune Up Kit for a Hayward pump with Model #SP3210X152 would you recommend? I need to replace my pool pump motor only (1.5 HP 2 Speed 56Y Frame). Thank you.
 Reply

A  Answered on 9/1/2017 by InyoPools Product Specialist Andy O.

Hello Collin- There isn't a tune up kit for the Tristar, but you can purchase the Pump Seal, Extra Heavy Duty PS4280 (Saltwater Pools) - PS-4280 which would be the salt water shaft seal for your pump.
 Reply


?     Asked on 8/26/2017 by Paul

Verify this is kit for Hayward sp4015x20 2 hp
 Reply

A  Answered on 8/26/2017 by InyoPools Product Specialist Lennox H.

Hi, Paul, This Hayward Super Pump Kit is not compatible with the SP4015X20 pump. You can use GOKIT66 if your pump was manufactured before 2003. 
 Reply


?     Asked on 6/18/2017 by Frank Young

I have a Hayward super pump that has to be at least 30 + years old! I want to buy a new pump with a VS motor. Do you have one that matches up to the original so I do not have to change the piping? When I went to commission the pool this year, the motor was seized at the shaft. I was able to free the motor with a little persuasion and WD-40. I converted to a salt water generator 3 seasons ago and never did anything to the pump to adapt to salt water. the pump seal did show signs of a leak
 Reply

A  Answered on 6/25/2017 by InyoPools Product Specialist Hector F.

Ultimately it will depend on the total horse power of your pump but you may be able to use the model SP2603VSP Hayward Super Pump Variable Speed Pump, the Pureline prime PL2606 or even the Pureline Prime PL2605. Keep in mind that you do have an older design so there may be slight plumbing adjustments but not much. 
 Reply


?     Asked on 5/14/2017 by Kathie

We have a salt system with a Hayward SP3010x15AZ. Can you tell me what seal kit we need? Thanks
 Reply

A  Answered on 5/14/2017 by InyoPools Product Specialist Hector F.

You would need the gokit2 or the gokit2salt for a salt pool.
 Reply


?     Asked on 5/16/2016 by Craig

You're the only guys who have a saltwater kit. What's the difference and is this a must have for a saltwater system?
 Reply

A  Answered on 5/17/2016 by InyoPools Product Specialist Robert M.

Hello Craig - The difference between this kit and the standard kit is the shaft seal. The shaft seal in the salt kit is specifically designed for salt water. The materials include viton elastomers, a carbon primary ring, a polished ceramic seal and stainless steel hardware. We definitely recommend this kit for salt pools.
 Reply


?     Asked on 5/16/2016 by Craig

Hi, Will this kit work with the century ust1202 motor? I'm going to replace the bearings also. Thanks, Craig
 Reply

A  Answered on 5/16/2016 by InyoPools Product Specialist Robert M.

Hello Craig - The GOKIT32SALT will work with the UST1202 as long as you have a Hayward Super Pump.
 Reply


?     Asked on 5/11/2016 by ron

How do you remove the impeller from the motor on a Hayward super pump?
 Reply

A  Answered on 5/12/2016 by InyoPools Product Specialist Robert M.

Hello Ron - Check out our guide on How To Replace a Pool Pump Impeller. This should walk you through the process.
 Reply


?     Asked on 4/21/2016 by Perry

Do you have instructions for the go-kit3v Vitos?
 Reply

A  Answered on 4/21/2016 by InyoPools Product Specialist Lennox H.

Hi Perry, You can view our How To: Use a Tune Up / GO-KIT along with the Hayward Super Pump Parts exploded diagram for installation instructions.
 Reply


?     Asked on 3/12/2016 by

Do any of the pump/motor combos have a saltwater shaft seal and an ee motor?
 Reply

A  Answered on 3/14/2016 by InyoPools Product Specialist Lennox H.

Hi, None of the Hayward Super Pumps pump/motor combos comes with a saltwater shaft seal or an EE motor.
 Reply


?     Asked on 3/12/2016 by

Does water slinger come with new motor?
 Reply

A  Answered on 3/14/2016 by InyoPools Product Specialist Lennox H.

Hi, The Slinger is included with all new motors.
 Reply


?     Asked on 3/10/2016 by Jim Elliott

I have a 1 1/2 hp Hayward super pump SP1610Z1M. Which tune up kit should i use.
 Reply

A  Answered on 3/11/2016 by InyoPools Product Specialist Andy O.

Jim- The correct tune up kit for the super pump is the gokit3 or if you have a salt system the gokit3salt.
 Reply


?     Asked on 2/1/2016 by Bill Z

I have a SP 1607-Z1-M pump. I've had the pump for 5 years and it is getting very loud. Will a GOTOKIT3Salt kit help this issue and is it the correct kit for me? Thanks
 Reply

A  Answered on 2/2/2016 by InyoPools Product Specialist Andy O.

Bary- The GOKIT3SALT would be the correct kit to prevent leaking into the motor bearings. Unfortunately, it sounds like water has already reached the internal bearings on the motor, which is why it is getting very loud. To correct the issue, you would either need to change the bearings in the motor or change the entire motor with its replacement which would be the UST1102 A.O. Smith 1 HP Round Flange Up Rate Motor.
 Reply


?     Asked on 10/12/2015 by sam

Do they have salt seals in the go kits ??
 Reply

A  Answered on 10/12/2015 by InyoPools Product Specialist Robert M.

Hello Sam - The shaft seal included in this kit is designed for salt water.
 Reply


?     Asked on 6/16/2015 by KC

Will this kit work on an SP 1800 pump with salt water generators?
 Reply

A  Answered on 6/16/2015 by InyoPools Product Specialist Joe S.

Yes, this GOKIT3Salt is made for salt water pools
 Reply


?     Asked on 6/15/2015 by Gary

I have a hayward super pump 1.5hp. On start up with in 5 seconds,trips the breaker. Ran fine last year. Noticed the white terminal connector is cracked and one screw is stripped. Could this be my issue or do I need to look further? Ran the mortor w/o the pump attached and have the same issue
 Reply

A  Answered on 6/15/2015 by InyoPools Product Specialist Dennis R.

Gary, If the cracked terminal and stripped screw are giving you a loose connection, you could be drawing excessive amps which could be tripping your breaker. Or your Motor bearings or windings could be going bad.
 Reply


?     Asked on 6/13/2015 by doug

I am replacing my c48k2n143b1 motor and need a tune up kit for a salt water pool, what kit will work, i have haywood max flo 2800 pump?
 Reply

A  Answered on 6/15/2015 by InyoPools Product Specialist Patrick P.

Hi Doug, you would require the GOKIT1SALT which is the tune up kit for the Hayward Max Flo Pump being used on a salt pool.
 Reply


?     Asked on 5/7/2015 by

I purchased this kit for the Hayward SuperPump SP2610X15. The spring seal is of a different design than the one that came off the pump. The Original spring seal has a rubber section on the bottom and expands over two "nubs" that are on the impeller shaft, and accommodate a ridge/step at the base. The new one will not fit over the impeller shaft, and has no way to accommodate the step. Any help would be appreciated.
 Reply

A  Answered on 5/8/2015 by InyoPools Product Specialist Robert M.

Hello Tom - It sounds like you still have a piece of the old shaft seal on the shaft of the impeller. The metal piece with the two nubs needs to be removed from the impeller. Once that is removed, you will be able to install the new shaft seal.
 Reply


?     Asked on 2/22/2015 by Jim

My pump model is Hayward SP2605X7 Super Pump. Will this kit work for me?
 Reply

A  Answered on 2/23/2015 by InyoPools Product Specialist Robert M.

Hello Jim - The GOKIT3SALT would be the correct kit for the Hayward SP2605X7.
 Reply


?     Asked on 10/15/2014 by Guest

My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
 Reply

A  Answered on 10/15/2014 by InyoPools Product Specialist Patrick P.

The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
 Reply


?     Asked on 10/14/2014 by Guest

What is the difference between the salt kit versus chlorine kit technically speaking ?
 Reply

A  Answered on 10/14/2014 by InyoPools Product Specialist Patrick P.

Both Gokits will have the same items, except  the gokit3 has a standard shaft seal made of standard rubber, the gokit3salt has a shaft seal that is made of VITON which will be able to handle the minerals in a salt pool longer.
 Reply


?     Asked on 2/16/2012 by Guest

What is the difference between the GOKIT3 and the GOKIT3SALT?
 Reply

A  Answered on 2/16/2012 by InyoPools Product Specialist Patrick P.

The GOKIT3SALT includes the heavy duty viton and carbon shaft seal. The heavy duty seals are designed for salt chlorine generators and ozonators.
 Reply


Top
Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver, Pliers, Socket Set, Wrench Set

Replaced motor so also replaced seals as recommended by INYO pool experts

Written on 8/9/2018 by Guest

Replaced Motor and installed seal kit on Heyward pump for 35,000 gal in-ground pool. Since my recent retirement I now have time to do this work myself saving hundreds of $ by not having to hire it done. The videos and directions were thorough and easy to follow. Take it from a first time, novice, impatient DIYer, if you can follow directions, you too can have the satisfaction of successfully repairing your own equipment and keeping your money invested in your 401K.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

2 to 4 hrs

Tools Needed

Screwdriver, Socket Set

Old motor

Written on 4/23/2017 by Guest

Replace seals and put in a new variable magnetic drive motor. Works great.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.75  out of 5 stars)
32 Rating
5 star:
 
(25)
4 star:
 
(6)
3 star:
 
(1)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews