Tune Up Kit Purex - Triton Dynamo/Dynamite Dynatron - GOKIT46



Part # GOKIT46

By Aladdin

  5 Average  



Part # GOKIT46

Alternate Part #'s PL1046

Product Description

INYOpools highly recommends replacing the shaft seal, o-rings and gaskets when replacing your motor, if you use your old shaft seal it will not mate up properly with the new pump and may leak. The best value is to go with one of INYO's tune up kits which include the shaft seal and all O-rings, gaskets and lubricant for your pump.

This Tune Up Kit Works on These Pumps:

  • All Pentair, Pac-Fab & Purex model's of the Dynamo 1/2 HP - 3 HP single and dual speed models.
  • All Pentair, Pac-Fab & Purex model's of the Dynatron 1/2 HP - 3 HP single and dual speed models.

Tune Up Kit Includes:

  • Motor Shaft Seal
  • Housing Gasket
  • Diffuser Gasket
  • Pump Lid O-Ring
  • Lubricant

For More Pool Pump Motors


?     Asked on 3/25/2020 by William Christopher Smith Jr.

Looking for a lid and or oring for a Pentair DYNII-N1-3/4HP Model: 340188 Would this work?

A  Answered on 3/26/2020 by InyoPools Product Specialist Hector F.

Yes, this is the correct seal/gasket kit for your pump and to view your lid options please click here to be directed to the Pentair Dynamo pump parts page. 

?     Asked on 7/8/2019 by James Andrews

Is this the correct o ring kit to replace a pool pump that is a Dynamo model number DYNII-N1 5 SPL and serial number 1-29-D11

A  Answered on 7/8/2019 by InyoPools Product Specialist Hector F.

Yes, this tune up kit will work for the Pentair Dynamo pool pump. 

?     Asked on 7/20/2017 by Nancy

Will the tune up kit help me with the noise the pump is making

A  Answered on 7/21/2017 by InyoPools Product Specialist Lennox H.

Hi, Nancy. A tune up kit will not alleviate noise from the pump but will stop water leaks. 

?     Asked on 7/15/2017 by Nancy

My pump is running louder than usual, what would you recommend to help me with this problem

A  Answered on 7/16/2017 by InyoPools Product Specialist Lennox H.

Hi, Nancy. If the motor is loud that's usually an indicator that the motor bearings are bad. You can either replace the motor bearings and or the entire motor. 

?     Asked on 4/28/2017 by Les

My kid dropped a small lid into the intake which ended up stopping the constant flow into the pump for about 10 plus minutes. Now the pump looses pressure when on waste and filter. Will this kit fix this issue? The pump operates fine. Just little 'suction' so to speak.... Thanks!

A  Answered on 4/28/2017 by InyoPools Product Specialist Scott W.

It might be your seals, but I would check to make sure your impeller is not broke or cracked first.

?     Asked on 6/27/2016 by Mike

will this kit work for dynamo DYNII-N1-1 Serial#1-20-G99

A  Answered on 7/3/2016 by InyoPools Product Specialist Alex V.

Mike, We do not have access to serial number but this kit will work on the Dynamo pump model you provided.

?     Asked on 5/22/2016 by

Will this kit work for a 1 hp dynamo DYNII-N1-1 Serial no. 1-10-E9

A  Answered on 5/22/2016 by InyoPools Product Specialist Patrick P.

Yes this kit will work for a 1 HP Dynamo pump.

?     Asked on 5/10/2015 by shawn

Have a Dynamo 1.5 hp #340210 pump leaking. Is this the gasket kit for this pump?

A  Answered on 5/10/2015 by InyoPools Product Specialist Patrick P.

Hi Shawn, Yes this would be the correct gasket kit for the your Dynamo pool pump.

?     Asked on 5/2/2015 by Tony

My pump has started to drip water and I have lost a lot of pressure at the discharge into the pool. I feel a tune-up would be a good choice?

A  Answered on 5/3/2015 by InyoPools Product Specialist Patrick P.

Hi Tony, Yes a tune-up is normally where I would always start as this will fix the leaking issue 90% of the time.

?     Asked on 10/15/2014 by Guest

My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?

A  Answered on 10/15/2014 by InyoPools Product Specialist Patrick P.

The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.

?     Asked on 2/13/2012 by Guest

I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!

A  Answered on 2/13/2012 by InyoPools Product Specialist Patrick P.

You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.


Review Summary

 (Average 5  out of 5 stars)
2 Rating
5 star:
4 star:
3 star:
2 star:
1 star:

The Most Recent Reviews