AquaCal HeatWave SuperQuiet Heat Pump 101,000 BTU's - SQ125AHDSBNP


Part # SQ125

By Aqua Cal

  5 Average  



Part # SQ125

Manufacturer Code SQ125AHDSBNP

Product Description


The NEW HeatWave SuperQuiet® SQ125 comes equipped with all standard features. The Patented ThermoLink Titanium Heat Exchanger at its core makes this unit a power-house that’s built to last.

At 55 db, the AquaCal® HeatWave SuperQuiet® heat pumps are virtually silent from 10ft. away! Making the right choice just got a whole lot easier.

  • Corrosion proof cabinet
  • Scroll Compressor – for quiet operation
  • Microprocessor Controls
  • Off-Set Plumbing

Corrosion Proof Cabinet

• Louvered side panels protect evaporator coil while

ensuring efficient airflow

• Rust and fade proof

• Impact resistant

• Built-in drain pan provides condensate management


• Air Flow Vectoring Top protects internal components

from weather and debris while ensuring optimal air flow


Microprocessor Controlled with Digital Display

• Flip-out control panel is out of sight, protected against

sun and weather

• Lockable panel provides security from others changing

the temperature

• Accurate and easy-to-read bright blue display

• On-board self-diagnostics

• Microprocessor controlled defrost cycle


ThermoLink® Titanium Heat Exchanger

• Patented counter-flow water management system

• Patented hydraulic design adds only 1 PSI at 30 GPM,

increasing compatibility with two-speed & variable

speed pumps

• Impervious to chemical corrosion

• Durability without sacrificing performance

• Lifetime warranty

Product Specifications

101,000 BTU
Heat Exchanger:
4.6 kW
60 Hz
Minimum Circuit Ampacity:
Recommended Breaker Size:
Min Flow Rate:
30 GPM
Max Flow Rate:
70 GPM
34" L x 34" W x 44" H
268 lbs.

?     Asked on 1/5/2018 by

Is it possible to install a remote controller for this pump along with making it acessable via a smart phone?

A     Answered on 1/5/2018 by InyoPools Product Specialist Lennox H.

Hi. Unfortunately, there is not controller specifically for this unit that will allow you to controller this unit via a smartphone. You will have to look into getting a Pool Automation.

?     Asked on 8/26/2017 by Gary Dunning

Researching good way to heat our Foxx vinyl lined in-ground 18x36 pool ~ 23k gallons. We live near 93430 CA. A neighbor suggested an Aqua Cal heat pump. So I would like to find out details. We have not heated our pool since having it installed in '89. Liner was replaced 2015 and remains in fine condition. Thank you.

A     Answered on 8/27/2017 by InyoPools Product Specialist Lennox H.

Hi, Gary. We carry a few AquaCal unit including this SQ125 model that can be used to heat your pool. You can read our Pool Heat Pumps Guide for the info required when sizing a heat pump for your pool. 

?     Asked on 6/9/2016 by wally piatkiewicz

what size heat pump would I need for pool 307 sq.ft deepest part is 5 feetabout 9800 gal of water live in Arizona

A     Answered on 6/9/2016 by InyoPools Product Specialist Scott W.

That's a great heat pump and would get the job done relatively quick. And being that you're in the hot state of Arizona that will help it out even more.

?     Asked on 5/23/2016 by Gene

Would this unit be size correctly for an in-ground 11500 gal pool in central FL? Also, any comment on how this brand compares to Sta-Rite/Pentair? Thanks, -gene

A     Answered on 5/25/2016 by InyoPools Product Specialist Alan M.

The AquaCal HeatWave SuperQuiet Heat Pump 100,000 BTU would be a great fit for an 11,500gal pool. The spec information and competitor brands have it very comparable in efficiency.

?     Asked on 9/19/2014 by Guest

We're building a 6 foot by 13 foot spa (3 feet depth) in Southwest Florida (Sarasota) and would like to know if the SQ110 heat pump would work well for that application, to get the temperature up as high as 95degF for use when the jets are on. Would I have the heat pump on all the time to maintain that temperature, or would I just use the heater an hour or two beforehand to get the temperature up?

A     Answered on 9/19/2014 by InyoPools Product Specialist Patrick P.

This heat pump will work well for what you are trying to do. You would turn it on an hour or two before and let it heat the spa up to the desired temperature, but just like with a normal heater in a spa you would have to leave it running while the spa is bubbling. The reason for that is because the bubbling allows heat to escape. If you've ever been in a spa where the heater is broken, you would have noticed that once the heater shuts off the water cools significantly. Therefore you would let it run to support the temperature.


Review Summary

  (Average 5 out of 5 stars)
1 Ratings
5 star:
4 star:
3 star:
2 star:
1 star: