AquaRite 15K Replacement Cell - TCELL3



Model # TCELL3

By Goldline Controls

  4.5 Average  



Model # TCELL3

Product Description

Replacement Turbo Cell for AquaRite 15,000 Gallon pools. Comes with 15' of cable and a 3 year warranty. This cell requires that you have a Power Supply with Software Revision 1.50 or higher

Product Specifications

Treatment Capacity:
15,000 gal.
3 yrs

?     Asked on 8/16/2018 by Delene Veach

My Aqua Rite is reading my salt level at 600 and when we attempted to recalibrate it only changed to -300 before jumping to 600 and then the check salt level and check salt generator light flashed on. Should I assume that my T-3 cell needs to be replaced? It is less than 3 years old and we haven’t had a huge amount of build up in it at all. Thanks for your help.

A     Answered on 8/16/2018 by InyoPools Product Specialist Lennox H.

Hi, Delene. If your Cell Voltage and Cell Amps are within the correct range, then the cell is bad and will need to be replaced. 

?     Asked on 7/24/2018 by Pat

I have a Goldline Turbocell 9 that I suspect is not working. My board is a PL-PS -8 (*3LO806 -1024841*) Main software revision 2.86 The board does not offer the Turbocell 9 as an option so I have selected 15 and it has been working fine until now. WHat cell do I need? Thanks

A     Answered on 7/25/2018 by InyoPools Product Specialist Joe S.

The cell you can use would be Aquarite Replacement Cell (TCELL15) - GLXCELL15 or Aqua Rite Salt Cell Replacement T-15 (2 Year Warranty) - PL7106.

?     Asked on 3/17/2018 by Lee Lobban

I replaced the board in 2014 G1-011056G-1A GLC 13280 0900003-159-01/4213. Will this accommodate the T-3 cell This is an inground pool 11000 gallons capacity

A     Answered on 3/27/2018 by InyoPools Product Specialist Lennox H.

Hi, Lee. That board will be able to accommodate the TCELL3. 

?     Asked on 10/26/2017 by Christopher Pyron

I have a GLX PCB board, the number on it is G1-011056-1 and, when I check the diagnostic board, I get a reading of 2.60. Will this board support a T-3 cell? Thanks for the help.

A     Answered on 10/26/2017 by InyoPools Product Specialist Lennox H.

Hi, Christopher. Yes, if the revision number is 2.60 then it will be compatible with TCELL3. 

?     Asked on 6/4/2017 by Marandy

I have a Hayward TurboCell T-Cell-5. I can't seem to find one anywhere. Will the T-Cell-3 work? Thanks

A     Answered on 6/6/2017 by InyoPools Product Specialist Lennox H.

Hi, Marandy. We do have the Hayward T-CELL-5 available, click this link >T-CELL-5.

?     Asked on 5/31/2017 by Gerri

Does it matter whether the cord hangs from the top or bottom when installed.

A     Answered on 6/3/2017 by InyoPools Product Specialist Lennox H.

Hi, Gerri. The cell can be installed in either direction.

?     Asked on 4/18/2017 by

Is the T-Cell-15 compatible my board, if I purchased the Aquarite 15K - AQR3?

A     Answered on 4/18/2017 by InyoPools Product Specialist Scott W.

Any of the t-cells will go with the control board, you just need to make sure after installing the cell that you set your control board to the t-cell that you installed. So if you install the T15 you would set your board to T15.

?     Asked on 9/4/2016 by David

Do you sell the inside plates?

A     Answered on 9/8/2016 by InyoPools Product Specialist Scott W.

No sir, we do not sell the inside plates, just the complete cell.

?     Asked on 8/17/2016 by Michel

My cell is Turbo-cell T-cell-5 3A1004-1035678 AQUA collection. My unit is Goldline AQ-TROL-RJ-CUL. Which cell do i use to replace my cell ?

A     Answered on 8/18/2016 by InyoPools Product Specialist Tim Q.

Hi, MichaelPlease be advised that you would need to check in your diagnostics on your control panel to verify that it's inner changeable. If your board is more then 7 years old it will not be and you will have to stay with the same cell you have. Here is a link to the T-cell-5 cell.

?     Asked on 8/12/2016 by MIKE PURL


A     Answered on 8/12/2016 by InyoPools Product Specialist Scott W.

Yes, that would be one of the replacement cells for that system.

?     Asked on 4/2/2016 by Ted Belden

How do you determine if the power supply has software revision 1.50 or higher?

A     Answered on 4/4/2016 by InyoPools Product Specialist Lennox H.

Hi Ted. On your controller you will press the "Diagnostic" 7 times to get to the Software revision level, that will tell you the revision software level of your unit.

?     Asked on 4/6/2009 by Guest

I have an AquaRite which is 5 Years old and think my software is different then the new cell requires. Which cell do I need?

A     Answered on 4/6/2009 by InyoPools Product Specialist Patrick P.

If you have an older unit (older than 2009) than you would require the GLXCELL15W which you may view or purchase here 


Review Summary

  (Average 4.5 out of 5 stars)
2 Rating
5 star:
4 star:
3 star:
2 star:
1 star: