Model # 009200
By Raypak
Model # 009200
Warranty 1 year
Manufacturer Code PR206AMP
Alternate Part #'s 009200
PLEASE NOTE: THIS IS A STOCK PHOTO. THE MILLIVOLT HEATER DOES NOT HAVE A DIGITAL DISPLAY/READOUT.
BENEFITS:
Dial control for temperature selection and heater settings
Capron resin headers prevent rust stains from harming pool surface
Plumb directly from provided 2" PVC threaded union
Smart microprocessor controls diagnostic read-out and continuously monitors operating status
Completely field serviceable
Small footprint
High efficiency
Guaranteed high wind reliability
Looks smart and works smart
1 Year Warranty
Thermal Efficiency of 83%
California Customers Please Note: South Coast Air Quality Management District ( SCAQMD) Area of Jurisdiction REQUIRES a Low Nox Heater be installed. The following 6 California Counties are affected: Los Angeles, San Bernardino, Ventura, Orange, Riverside, & Kern. Installing a non-compliant heater in these counties will void the manufacturer's warranty and could result in a fine from your local code enforcement.
Click here for RayPak Low Nox Heaters
Elevation: 0 Ft. – 2000 Ft. Click Here for High Altitude Pool Heaters
Dimensions:
What would be the most efficient unit you have for a 16x32 pool
Electric
Propane
Or
Natural gas?
Cost wise?
Thank you for your respnose
God bless
Reply
Hi, Michael. You can use the Raypak Pool Heater Sizing App to compare cost and determine what size unit will be more efficient.
Reply
Can you pipe the heater and does the heater come with its own pump?
Reply
This unit would need to be piped using the unions that come in the packaging and will need to be piped into your equipment after the pump since as it does not have it's own pump.
Reply
I have a Raypak 206A Natural gas and would like to convert it to LP is there a kit and or individual parts I can purchase to make the switch? I know defiantly orifices but am unclear if the gas valve needs replacing.
Thanks
Reply
Hi, Roger. If you have the MilliVolt (MV) unit, the NG to LP Conversion Kit is Part # 004690B. If you have the Electronic (IID) unit, you will have to replace the entire Burner Tray Assembly which is Part # 010411F. If you can provide the complete model # of your unit I can confirm what you'll need.
Reply
what size of s pool heater would I need for a 25' round above ground pool, my last heater was a Pentair, and it seemed to take a long time to heat up the water in pool, would like something that would have a quicker response. what would you suggest?
Reply
Hello. I will provide you with a few suggestions you can research. Hayward A/G Pool Heater 100000 BTU NG ELE MODEL# H100ID1 at page ww.inyopools.com/Products/02200459000638.htm?Keywords=h100id1 Next would be for the Propane option Hayward A/G Pool Heater 100000 BTU LP MODEL# H100IDP1 at page http://www.inyopools.com/Products/02200458000639.htm?Keywords=h100idp1 I would also recommend using a solar blanket so you do not loose heat during times of evaporation. Please review the 28' Round Clear Pool Solar Blanket MODEL# NS488 at Page http://www.inyopools.com/Products/00100001005484.htm You would need to cut the blanket to fit 3-4" less than the actual size of your pool. In your case, the pool is 25' round and we do not offer one that size.
Reply
I have a confined space I am attempting to fit a heater into, what are the dimensions of the heater cabinet?
Reply
For the Raypak 206 BTU RP2100 Series the cabinet measures are as follows:Width - 20 inches, Depth - 28 inches, Height - 38 inches. Any fuirther techinical data be found in the Raypak Specifications Guide
Reply
Can this heater be converted from propane to natural gas?
Reply
