Raypak Heater 266000 BTU LP MV - PR266AMP



Part # 009201

By Raypak

  4 Average  



Part # 009201

Warranty 1 year

Manufacturer Code PR266AMP

Alternate Part #'s 009201

Product Description



  • Dial control for temperature selection and heater settings

  • Capron resin headers prevent rust stains from harming pool surface

  • Plumb directly from provided 2" PVC threaded union

  • Smart microprocessor controls diagnostic read-out and continuously monitors operating status

  • Completely field serviceable

  • Small footprint

  • High efficiency

  • Guaranteed high wind reliability

  • Looks smart and works smart

  • 1 Year Warranty

  • Thermal Efficiency of 83% 



California Customers Please Note:  South Coast Air Quality Management District ( SCAQMD) Area of Jurisdiction REQUIRES a Low Nox Heater be installed.  The following 6 California Counties are affected:  Los Angeles, San Bernardino, Ventura, Orange, Riverside, & Kern. Installing a non-compliant heater in these counties will void the manufacturer's  warranty and could result in a fine from your local code enforcement.    Click here for RayPak Low Nox Heaters


Elevation: 0 Ft. – 2000 Ft. Click Here for High Altitude Pool Heaters


Raypak Pool Heater Dimensions

Raypak Pool Heater Dimensions

Raypak Heater Dimensions

  • California Customers Please Note: South Coast Air Quality Management District (SCAQMD) Area of Jurisdiction requires a Low Nox Heater be installed.  The following 6 California Counties are affected:


Product Specifications

266,000 BTU
Digital Readout:

?     Asked on 6/28/2017 by linda

how far does the pool heater have to be from the house - huntington ny

A     Answered on 6/29/2017 by InyoPools Product Specialist Joe S.

For U.S. installations, the point from where the flue products exit the heater must be a minimum of 4 ft below, 4 ft horizontally from, or 1 ft above any door, window or gravity inlet into any building. The top surface of the heater shall be at least 3 ft above any forced air inlet, or intake ducts located within 10 ft horizontally

?     Asked on 6/12/2017 by James Gibson

Why does my limit switch or rollout goes bad when we have a windy day. What can I do to prevent it.

A     Answered on 8/5/2017 by InyoPools Product Specialist Alex V.

James, That will happen with a millivolt heater. There is not much you can do to prevent it. 

?     Asked on 5/27/2017 by

how to winterized a raypak heater and where are the drain plugs thank you .gerry

A     Answered on 5/28/2017 by InyoPools Product Specialist Stacey M.

Hello, Normally all units come with the instructions on winterizing, these are different with each heater, but turn off you gas, make sure ignitor is off, instructions may only say to remove the drain plug. You can (if you would like) blow compressed air through the heater with the drain plugs removed until you see no misting come out of the drains. Then pause the air flow and do it again. And maybe again. You want to get as much water out of the heater element as possible. Only use about 20-30 psi if you're using a compressor. Again this is different for each type of heater, please follow owners manual instructions.

?     Asked on 5/21/2017 by Jeff

What are the shipping carton dimensions and weight for this heater?

A     Answered on 5/23/2017 by InyoPools Product Specialist Lennox H.

Hi, Jeff. The shipping dimensions are Height – 28", Width – 30.5", Length – 45.0".

?     Asked on 6/12/2016 by joe

is the water inlet and outlet on the right or left side

A     Answered on 6/12/2016 by InyoPools Product Specialist Matt S.

If you're facing the heater, the in/out ports are on the right. But the Raypak headers can be reversed and set on the left side.

?     Asked on 8/23/2013 by Guest

Can this heater be converted from propane to natural gas?

A     Answered on 8/23/2013 by InyoPools Product Specialist Patrick P.

This heater can be converted from propane to natural gas as there is a conversion kit to do so. The part or model number for the conversion to natural gas is: 6234-300.

?     Asked on 10/10/2012 by Guest

What is the difference between an Electronic and Millivolt ignition?

A     Answered on 10/10/2012 by InyoPools Product Specialist Patrick P.

The basic answer is that Millivolt is the old style of ignition, using a standing pilot light. While the electronic ignition uses a spark start system like a gas grill. Electronic ignitions are more efficient in gas usage and also are better suited for high wind areas where a pilot light might get extinguished.

?     Asked on 1/16/2012 by Guest

Will a gas heater operate at the low speed of a dual speed motor?

A     Answered on 1/16/2012 by InyoPools Product Specialist Patrick P.

Probably not - Most gas heater will shut off at low GPM levels (20-40) to keep the heater cores from overheating - 20 for 200 BTUs, 40 for 400 BTUs. Depending on your pool system you might get these GPM levels at the low speed but generally these heaters must be run at the motor's high speed.


Review Summary

  (Average 4 out of 5 stars)
2 Rating
5 star:
4 star:
3 star:
2 star:
1 star:

The Most Helpful Review

The Most Recent Reviews