PC BOARD CONTROLLER & 3-WIRE-KIT - 013464F

$275.99

IN STOCK
FREE SHIPPING

Part # 6238-570

By Raypak

  5 Average  

Details

Top

Part # 6238-570

Manufacturer Code 013464F

Dimensions 7.6" L x 4" W x 1.6" D

Alternate Part #'s 013464F, 601944

Product Description

PC BOARD CONTROLLER 207A-407A & 206A-406A 3-WIRE-KIT

Top

?     Asked on 11/30/2018 by David Klein

Is this a replacement for 601944, 1134-700? Thank you in advance for your response.
 Reply

A  Answered on 12/3/2018 by InyoPools Product Specialist Lennox H.

Hi, David. Yes, this is the correct replacement board based on the info provided. 
 Reply


?     Asked on 6/15/2018 by Jeff

I have a raypak model # P-M206A-EN-C s/n 1003074892 display not readable heater works fine just want to make sure I order correct part
 Reply

A  Answered on 6/15/2018 by InyoPools Product Specialist Lennox H.

Hi, Jeff. Based on the model and serial number, you will need Part # 010253F
 Reply


?     Asked on 5/8/2018 by Gene

Hi, I bought item #014941 - Raypak Heater 406,000 BTU's NG ELE W/ Cupro-Nickel Heat Exchanger from you guys a couple years ago. When I try to fire up the heater, it doesn't seem to sense when the burners are lit. Everything operates fine until after the burners light, then it turns itself off and re-lights itself over and over. Is this the part that will fix this issue?
 Reply

A  Answered on 5/8/2018 by InyoPools Product Specialist Lennox H.

Hi, Gene. It's possible if you've reset the PC board and checked the continuity of ignition cable and ground wire, and that the pilot flame covers flame rod and is steady and blue. If these two checks out then the PC Board is bad. You will need Part #010253F for your model heater. 
 Reply


?     Asked on 3/19/2018 by Terry

Is this board compatible with the "Control Panel, Iid, Digital (006739f)"? This is the original lid and Switch/Decal membrane on the Raypak 2100 model 405A. The LED on my board is cracked. The heater still works but I have no idea of temp/set point/mode of operation. It appears I need this new board which is compatible with the 405A. So if I purchase this board, do I also purchase the newer 013492F membrane switch or will the 006739f work.
 Reply

A  Answered on 3/27/2018 by InyoPools Product Specialist Lennox H.

Hi, Terry. This PCB - 013464F is not compatible with the Control Panel IID - 006739F. The correct PCB is part # 010253F
 Reply


?     Asked on 8/19/2017 by MIchael

Hi, I have a Raypak PR266A EN-C heater and it just stopped heating, When you activate the heat the display shows "CFH" and then "SPK" and the burners do not light. I replaced the standing pilot and tubing but still not firing. Checked 24v transformer and it appears to be ok. So I'm thinking its either the gas valve and or the PC board. Can you recommend the correct replacement parts for both?
 Reply

A  Answered on 9/28/2017 by InyoPools Product Specialist Lennox H.

Hi, Michael. To find out if the gas valve or PCB is the issue; you'll need to check for 24 VAC across MV-MV/PV terminals. If no voltage, replace PC board. Also, check electrical connections between PC board and gas control. If okay, replace gas valve or gas control operator, i.e. pilot gas valve, flow switch etc.
 Reply


?     Asked on 5/30/2017 by Tom C

I have a rheem/raypak heater Model#P-M266A-EN-C Serial#0412009103. I'm getting a GVO error which means Gas Valve Open. I was told a new board Raypak#013463F would fix this problem?
 Reply

A  Answered on 6/4/2017 by InyoPools Product Specialist Lennox H.

Hi, Tom. To find if the problem is the PCB or the Gas valve, follow these steps.1. Turn power OFF and disconnect Ignition Wire and Gas Valve wires from board.2. Power ON and watch for spark at module.3. If no spark, turn power OFF, and replace board.4. If spark is observed, turn off power and reconnect wires. The unit should fire.5. If unit does not fire and code reappears, power OFF, disconnect valve wires from board and remove MV, PV, and ground wires. Clean and reconnect.7. If unit does not fire, replace the gas valve.8. Low power to transformer can cause a GVO fault.
 Reply


?     Asked on 3/27/2017 by 337A

does the replacement PC board come with the 3 wire sensor as well? I was given part number 013464F. Is this everything I need to replace the PC board when I order this or is there something else?
 Reply

A  Answered on 3/30/2017 by InyoPools Product Specialist Lennox H.

Hi, The part does include the 3-wire kit along with everything needed to install the board. Some customers usually replace the decal if faded when replacing this board.
 Reply


?     Asked on 6/25/2016 by Rick

I have a Rheem propane pool heater - Item #009975 and S/N 1104109848. I'm not sure when it was manufactured (I think we installed it 4-5 years ago). I need to replace the PC board. My owners manual says the part is 013489F. Will the 013464 work?
 Reply

A  Answered on 7/2/2016 by InyoPools Product Specialist Lennox H.

Hi Rick, I was not able to cross reference item # 009975 to a specific model or have the ability to use the serial number to search for an item. The 013489F and  013464 are not interchangeable, you will have to use p/n 013489F.
 Reply


?     Asked on 5/21/2016 by Kimberly Yoder

looking to replace and not sure what i need for a rheem ray pak heater ...my display is not readable, have no idea temp settings? Serial #0812047113 Model #pm336aenx BTU/HR inp 332500....ignition board or control panel kit???
 Reply

A  Answered on 5/22/2016 by InyoPools Product Specialist Matt S.

Kimberly, if you need the display, the correct part number is the 013464F PC Board Controller and 3-Wire Kit. In our picture, we do not show the LCD screen on the backside of the board.
 Reply


?     Asked on 4/27/2016 by Lynn

pool Heater model 266A don't find part # 013464F on control board. Has 601944 ID 026 1134-700 0714N502317 What is replacement part and how assured it is bad?
 Reply

A  Answered on 4/28/2016 by InyoPools Product Specialist Lennox H.

Hi Lynn, In order to get you the correct PCB, we will need to know the year that your unit was manufactured. We're unable to use the info you provided to located the correct replacement PCB.
 Reply


?     Asked on 3/12/2016 by

is the board 405b work in a 406a water heater?
 Reply

A  Answered on 3/17/2016 by InyoPools Product Specialist Lennox H.

Hi, This PC Board (013464F) can be used in the R405B manufacture date 11/03-10/04 and R406A manufacture date 11/04- current units.
 Reply


?     Asked on 6/16/2015 by Dave

Is this part a plug and play replacement for the older style board that does not have the replaceable LCD display? P/N 601769
 Reply

A  Answered on 6/18/2015 by InyoPools Product Specialist Lennox H.

Dave, This PC BOARD CONTROLLER & 3-WIRE-KIT will work on all models that have a digital display and electronic ignition.
 Reply


?     Asked on 6/11/2015 by Neil Martin

Does this work for the propane milli volt model? Does it include the display? Thanks.
 Reply

A  Answered on 6/12/2015 by InyoPools Product Specialist Patrick P.

Hi Neil, this board does include the display but it does not work with the milivolt units only the electronic ignition (IID) units.
 Reply


Top

Review Summary

 (Average 5  out of 5 stars)
1 Ratings
5 star:
 
(1)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)