1/4" Drain Plug with Gasket - SPX1700FG

Part # 6761A

By Hayward Pool Products

  4.89 Average  

Details

Top

Part # 6761A

Manufacturer Code SPX1700FG

Dimensions 0.9" L x 0.75" W x 0.75" D

Alternate Part #'s HAY1012034, SP1700FG, SPX1700FG

Product Description

Threaded black drain plug 1/4" includes gasket and is used on a number of common Hayward pumps including the Super Pump, Super II, Power Flo LX, and Power Flo II & III.  This plug is also used on some pool filter valves; it fits the Poolco, Zodiac TM-12-H8, and Splash Pak & Flo Pro multiport valves.

Top

?     Asked on 8/5/2017 by Carol Loughran

Does this part need to be grounded?.
 Reply

A  Answered on 8/7/2017 by InyoPools Product Specialist Lennox H.

Hi, Carol. This part does not need to be grounded. 
 Reply


?     Asked on 6/1/2017 by Gary

As in the question from May 25 replaced drain plug and still will not tighten so female side must be stripped any other solutions besides replacing the housing?
 Reply

A  Answered on 6/3/2017 by InyoPools Product Specialist Lennox H.

Hi, Gary. Unless you have a way to fix the threads, replacing the housing is the only other option.
 Reply


?     Asked on 10/25/2016 by Adi

My drain plug on my pool pump broke and the threads are stripped. What do you suggest I do? Can I just seal the drain hole for now?
 Reply

A  Answered on 10/25/2016 by InyoPools Product Specialist Adam Y.

Good Morning Adi, Is it on the basket or the valute? What style/model pump do you have. Can you send any pictures?
 Reply


?     Asked on 8/4/2016 by kelli

I think my Drain plug is leaking but only when the pump is shut off. 1. Do I need to put teflon tape around the new drain plug? 2. Could the threads be stripped on the inside of the pump housing it self?
 Reply

A  Answered on 8/7/2016 by InyoPools Product Specialist Lennox H.

Hi Kelli, Teflon tape is not required because it has a gasket. The threads can be stripped if it's still leaking after it's been replaced. You can inspect the threads with your finger.
 Reply


?     Asked on 5/29/2016 by joanne

I have lost the drain plug and this is my serial # 36110CH can you tell me if this is the correct plug to order? thanks
 Reply

A  Answered on 5/29/2016 by InyoPools Product Specialist Alex V.

Joanne, Unfortunately, we do not have access to serial numbers. Please provide the make and model of your filter.
 Reply


?     Asked on 7/30/2015 by don taylor

the 1/4" drain plug with gasket. is it a pipe thread size?
 Reply

A  Answered on 7/31/2015 by InyoPools Product Specialist Lennox H.

Hi Don, The 1/4" Drain Plug with Gasket (SPX1700FG)  is pipe thread. 
 Reply


?     Asked on 5/25/2015 by

I went to open my pool today and this 1/4" drain plug is leaking and can't be tightened to stop the leak. Any suggestions if the female thread where this screws into is stripped? Thanks!
 Reply

A  Answered on 6/3/2015 by InyoPools Product Specialist Lennox H.

If tightening hasn't stopped the leak, the gasket or the thread is probably bad on the drain plug. Replacing it is the only way to figure out if the drain plug is the problem.
 Reply


?     Asked on 5/20/2015 by tom k

where does this go on the filter.
 Reply

A  Answered on 5/20/2015 by InyoPools Product Specialist Lennox H.

Tom, The Drain Plug with Gasket is usually located in the rear or lower left/right side of the pump housing. For filter's it's located right above the sight glass on the multiport valve.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver

Drain Plug Damaged

Written on 3/12/2019 by Guest

The drain plug on my Hayward 1.5HP pump snapped off. I had to use a small sharp screwdriver to get a good grip on it and extract the old plug. Make sure you thread it with Teflon tape on the new plug.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.89  out of 5 stars)
9 Rating
5 star:
 
(8)
4 star:
 
(1)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews