Cleaning Stand For Turbo Cells - GLX-CELLSTAND

$34.99

IN STOCK
FREE SHIPPING

Part # 2804-33

By PureLine

  4.47 Average  

Details

Top

Part # 2804-33

Manufacturer Code GLX-CELLSTAND

Dimensions 6-3/8" X 2-1/2"

Alternate Part #'s GLXCELLSTAND, PL7110, TCELLCLEANINGSTAND

Product Description

PureLine Crystal Pure & AquaRite Cell Cleaning Stand

Salt Cell Cleaning Stand for AquaRite Turbo Cells and PureLine Crystal Pure

This cleaning stand simplifies cell cleaning and eliminates having to soak cell in a bucket of muriatic acid solution. This Cleaning stand is used for Hayward, AquaRite, AquaTrol, Goldline Turbo salt cells and PureLine Crystal Pure salt cells. You should clean your salt cell every 2 months to avoid calcium build up on your salt cell. By cleaning your salt cell regularly you will prolong the life of the cell. Also if you get too much calcium build up on the salt cell then the system will stop producing chlorine, regular cleanings ensure that your salt system will not stop producing chlorine.

Compatibility: This stand fits the cells used on the AquaRite and AquaTrol salt systems. For Hayward AquaRite & AquaTrol salt systems you will commonly see the following part #'s marked on your salt cell T-15, T-CELL-15, GLX-CELL-15, T-9, T-CELL-9, GLX-CELL-9, T-5, T-CELL-5, GLX-CELL-5, T-3, T-CELL-3, or GLX-CELL-3This stand fits the cells used on the AquaRite and AquaTrol salt systems.

Top

?     Asked on 4/7/2019 by scott

I'm thinking that this will also work on my Pureline chlorinator cell - can you confirm?
 Reply

A  Answered on 4/7/2019 by InyoPools Product Specialist Lennox H.

Hi, Scott. Yes, this Cleaning Stand will also work with Pureline cells. 
 Reply


?     Asked on 5/17/2018 by Marilyn

This is totally embarrassing. After cleaning my cell, I can't remember which way to hook it back up. It would be nice if it had an arrow for the direction of the flow. Once you tell me, then I will draw an arrow on with a Sharpie. Just tell me if the cord is on the right as the water flows right to left? Thanks.
 Reply

A  Answered on 5/19/2018 by InyoPools Product Specialist Lennox H.

Hi, Marilyn. The Turbo Cell can be installed in either direction. 
 Reply


?     Asked on 9/20/2017 by Steve

Turbocell cap stand works great however, when I remove the Turbocell for cleaning, my pool drains from the return pipe and there is no shutoff valve on this end of the return system. Is there a threaded plug I can purchase to stop the pool from backflushing while cleaning my turbocell? If so, please advise where I can get one.
 Reply

A  Answered on 9/21/2017 by InyoPools Product Specialist Lennox H.

Hi, Steve. You can purchase the Turbo Cell Placeholder - GLX-CELL-PIPE to resolve the issue that you're having when cleaning the cell. 
 Reply


?     Asked on 4/18/2017 by harry T

Will this work on Hayward Turbo Cell T cell 15.?
 Reply

A  Answered on 4/18/2017 by InyoPools Product Specialist Lennox H.

Hi, Harry. Yes, this can be used with the Hayward T Cell 15 cell.
 Reply


?     Asked on 11/28/2014 by Mary

How does this clean salt cell? Do You pour acid into the stand? Thanks
 Reply

A  Answered on 12/1/2014 by InyoPools Product Specialist Brian M.

Hello Mary - That is correct, in a way. You would screw the cell onto the stand. You would then pour a mixture of water and acid. A ratio of 3 parts water and 1 part acid is the best to start. You would then let site for about 10 - 15 minutes, pour out the mixture and unscrew and spray out with a garden hose. If you click HERE , you can see a video detailing the process.
 Reply


?     Asked on 7/16/2009 by Guest

Can I use this cleaning stand on any other cell or is it just used on the AquaRite cells?
 Reply

A  Answered on 7/16/2009 by InyoPools Product Specialist Patrick P.

This stand will only mate up with AquaRite and AquaTrol salt cells.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

None

Dirty Turbo cell

Written on 10/24/2019 by Guest

Place turbo cell in stand and soak. Very easy

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Optional if needed; large adjustable pliers to loosen the clamps that hold the salt generator module

Salt generator maintenance

Written on 9/9/2019 by Guest

Salt pools, while they feel a lot nicer; the salt generator needs maintenance (like most of the pool equipment).

The salt cell breaks down salt, separating the chloride from the sodium, and converting the chloride into a form of chlorine that will keep the pool clean (similar to how chlorine tablets do).

The problem is... this electrical process causes deposits of minerals on the salt generator. The solution is to clean the salt generator, once or twice a year, depending on how long your swim season goes.

Cleaning is simple:
*Turn off the pump and salt generator power (better at the circuit breaker)

*Turn off the power switch in the salt generator panel and remove the salt generator module wire from the salt generator panel.

*Remove the salt generator module and replace it with the dummy tube... the reason to do this is both to keep the pool water from running out and to keep the pump primed.
*Attach the salt generator module to the stand, screwing it on, with the wire at the up end.

*I prefer to use vinegar mixed with water: one to one, put the vinegar in a container and add the water.

*Pour this solution into the salt generator and let it soak for 15-20 minutes

*Rinse out the salt generator thoroughly and inspect (look inside) to see if the plates are clean. If not, repeat the soaking procedure

*When the generator module is clean, remove it from the stand

*Remove the dummy pipe and re-install the generator, connecting the wire to the salt generator panel.

*Visually check for any things that look different than when you took it apart... it is good to take a cell pic before you start, then compare it after you re-assemble.

*Turn the power back on at the breaker, leave the power switch at the salt generator panel off.

*Start the pump and let it clear the pump of air... then let the air out of the top of your filter.

*Turn the salt generator panel switch on and let it run for a day

*Test salt content in the pool and adjust the generator output.

There you go, your salt generator is now cleaned and ready to keep your pool water feeling silky and keep the water clean!

Regular cleaning will extend the life of the salt generator module, so keep it clean!
THX for reading, now enjoy your pool!

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

None

Calcified Cell

Written on 7/9/2019 by Guest

Used your excellent stand on my chlorinator with muriatic acid and in minutes it came out like new and worked like NEW!! If u fill your pool with well water, it's a must!

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

None

Calcified Cell

Written on 7/9/2019 by Guest

Used your excellent stand on my chlorinator with muriatic acid and in minutes it came out like new and worked like NEW!! If u fill your pool with well water, it's a must!

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Pliers

Could mot fit in bucket

Written on 7/11/2018 by Guest

Purchased the cleaning stand now I only use half of the solution and 1/3 of the time. Well worth the $$$

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.47  out of 5 stars)
13 Rating
5 star:
 
(6)
4 star:
 
(7)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews