AquaPlus / ProLogic Main PCB - All Date Code/Versions - GLX-PCB-PRO

$537.99

IN STOCK
FREE SHIPPING

Part # 2807-45

By Hayward Pool Products


Details

Top

Part # 2807-45

Manufacturer Code GLX-PCB-PRO

Dimensions 9-1/8" X 6"

Alternate Part #'s GLX-PCB-PRO, GLXPCBPRO

Product Description

Your Source for Swimming Pool & Spa Parts With 40,000 Parts in Stock - INYOpools.com

Top

?     Asked on 3/28/2020 by TAMMY

Hi we are trying to find out which PCB main board to order. We know it's Hayward Aqua Plus but not sure which one we need. The numbers we found on the board are G1-015043H also found a sticker that says G1-011049F

 Reply

A  Answered on 3/28/2020 by InyoPools Product Specialist Patrick P.

Hi Tammy, Thank you for the photo and part #'s those were helpful. You will require the 2807-45 PCB Board listed on this page.
 Reply

  • Commented on 3/28/2020 by Product Owner

    Thank you!
     Reply


?     Asked on 3/24/2020 by Chris L

Bought a house with older equipment. Looking to replace main board for newer features. Panel has ProLogic label. Board part # is G1-066008J-1. What is the difference between the PRO and MAIN board? Will the PRO work?
 Reply

A  Answered on 4/1/2020 by InyoPools Product Specialist Lennox H.

Hi, Chris L. The difference between the two boards boils down to hardware and software. Yes, the PRO board will work with your ProLogic panel. 
 Reply


?     Asked on 12/30/2019 by Richard

Need part # to replace board to PL-PLUS. 3L1008-1214714
 Reply

A  Answered on 12/30/2019 by InyoPools Product Specialist Lennox H.

Hi, Richard. This is the correct replacement Main PCB for your controller. 
 Reply


?     Asked on 9/9/2019 by Dan Wilson

I have an old aqua logic p-4 or ps-4 not sure. Can I do a PCB update to use a hayward VSP and get all 8 speed settings? Thanks Dan
 Reply

A  Answered on 9/10/2019 by Industry Professional

Yes is what we determined. Hayward Goldline AquaLogic Main PCB Circuit Board | GLX-PCB-MAIN. (59-150-1012 ) Use this newest revision circuit board for AquaLogic systems to operate the new EcoStar variable speed pumps. This board is compatible with all date codes. If your system has a "heater button" at the power center then you can use the GLX-PCB-PRO circuit board instead of replacing it with this one. Doing this will upgrade your system to a ProLogic from your existing AquaLogic. Heater button is located on the local display (mounted in subpanel). It is important to make sure you have a heater "button", not just a heater light. This button will determine if your system can be upgraded to a ProLogic which is only a few dollars more and will give you more options. These systems can be very confusing & Hayward does offer great tech support to the end user if you want to call direct to verify.
 Reply

  • Commented on 9/10/2019 by Product Owner

    Thanks, no heater button so I'll get the MAIN.
     Reply


?     Asked on 9/4/2019 by Vikki Adair

I too have a Hayward Goldline Aqua Plus PL PLUS. I was told I needed a GLX-PCB-PRO board to replace mine because it won't keep time or day anymore. I am getting conflicting information on whether or not this board will work with my unit. Can you help? Thanks!
 Reply

A  Answered on 9/4/2019 by InyoPools Product Specialist Lennox H.

Hi, Vikki. This GLX-PCB-PRO is compatible with the Hayward Goldline AquaPlus controller. 
 Reply


?     Asked on 8/23/2019 by Jason KING

Hi I am looking to replace Aqua Plus control board Pn# G1-066008J-1. Is this the correct opart #
 Reply

A  Answered on 8/23/2019 by InyoPools Product Specialist Lennox H.

Hi, Jason. This Main PCB - GLX-PCB-PRO can be used as a replacement although Pn# G1-066008J-1 cross reference to the Main PCB - GLX-PCB-MAIN.  
 Reply


?     Asked on 8/2/2019 by

I have part # G1-011049D-1T. Is this the same board?
 Reply

A  Answered on 8/9/2019 by Industry Professional

Yes it should be the correct board.
 Reply


?     Asked on 7/20/2019 by Daniel M McCarthy

Hello, I have PL-PS-8 pro logic. Is this the right replacement circuit board?
 Reply

A  Answered on 7/20/2019 by InyoPools Product Specialist Lennox H.

Hi, Daniel. Yes, this is the correct replacement Main PCB. 
 Reply


?     Asked on 6/18/2019 by

Need to replace my board. Part G1-066008K-1. Installed 2006. Aqua Logic P-4 system. What is the replacement board ?? I’m seeing conflicting info. Thx
 Reply

A  Answered on 6/18/2019 by InyoPools Product Specialist Lennox H.

Hi. The Main PCB Pro board can be used with the AquaLogic P-4 allowing it to be compatible with more current features. 
 Reply


?     Asked on 6/17/2019 by Chris

I'm getting the chlorinator off, high salt/amps reading on my Goldline PL-Plus. The T-15 cell was replaced last year. Is the PCB-PRO the correct mother board for my unit?

 Reply

A  Answered on 9/30/2019 by Industry Professional

Yes, this would be the replacement for all dates & versions.
 Reply


?     Asked on 6/14/2019 by Jeff

I just purchased and installed GLX-PCB-PRO replacement board for my Aqualogic system. I am now getting a check system CSM Comm Error. How do I move past this.
 Reply

A  Answered on 6/14/2019 by InyoPools Product Specialist Lennox H.

Hi, Jeff. The CSM Comm Error is an error with the chemistry sensing module not communicating with the main circuit board. If you have Sense & Dispense, use the Sense & Dispense Troubleshooting Guide to locate and resolve the issue. 
 Reply


?     Asked on 6/10/2019 by Chris

I'm getting the chlorinator off, high salt/amps reading and am looking to replace the PCB. Is the difference between the MAIN and PRO PCBs the ability to use remote control function? Can I use either one if I'm not utilizing that feature?

 Reply

A  Answered on 10/2/2019 by Industry Professional

Yes the ability to use a remote & to operate variable speed pumps.
 Reply


?     Asked on 6/4/2019 by michael

i bought this prologic main pcb part from you. my question is will i have to reprogram all my pool settings when i install it ? timers,lights,date and time, filter and pool cleaner run time etc.. your part number is # 2807-45 thanks
 Reply

A  Answered on 6/7/2019 by InyoPools Product Specialist Patrick P.

Hi Michael, Yes, unfortunately, all of these items will need to be re-programmed.
 Reply


?     Asked on 5/31/2019 by

I have the Hayward goldline aqua logic control board. My pool has a water feature. Today the when I press the button on either the main panel or the desktop in the house to turn on the filter and pool lights, they go on fine, however the buttons no longer work to turn on the cleaner nor the water feature. The screen in the house still is functioning but the screen outside is blank and all i hear is a beep every 3-5 seconds. Would this be a mother board issue? Or just the control panel?
 Reply

A  Answered on 10/15/2019 by InyoPools Product Specialist Steve M.

We apologize for the inconvenience, however, we have been unable to obtain an answer to your question from the manufacturer regarding this. We are not certified by Hayward to offer troubleshooting advice for this system. You would need to contact them directly by calling 800.429.9273.
 Reply


?     Asked on 5/24/2019 by Armando Torres

I have a Hayward Pro Logic system. The display would not come on so went to the Hayward site and did performed the test and determined that the local display was not working. I have installed it at it turns on but now the display reads communication error. I have looked but cannot seem to find anything on how to diagnose what could be wrong
 Reply

A  Answered on 5/24/2019 by InyoPools Product Specialist Steve M.

Hi, Armando. Test the wiring harness for damage and test continuity (matching wire colors). If continuity is found on each wire, replace the Local Display.
 Reply

  • Commented on 5/25/2019 by Product Owner

    Thank you I did test the wires and there was continuity. I have replaced the local display which was not turning on before and the new one does turn on. Once it turns on I get what version the software is then it just displays communication error.
     Reply


?     Asked on 5/23/2019 by Brooke

Just replaced T-CELL to 15 from a T-CELL 5. Received an error of Chlorinator OFF, High Salt/ Amps, updated the T-CELL # in the configuration and the error resolved but then appeared again the next afternoon. Confirmed the correct cell #, salt level was 3400 but my now my display is not providing salt level. I believe the firmware is 4.15; the board is approximately 8 years old. What do to?
 Reply

A  Answered on 5/23/2019 by InyoPools Product Specialist Steve M.

Hi, Brooke. You will need to test your pool water to determine the actual salt level, reset the chlorinator. If the controller is reporting a voltage of 35V or higher,  replace the main pcb board.
 Reply

  • Commented on 5/23/2019 by Product Owner

    Display is now showing salt level of 3400 and planning to test actual water. How do you reset the chlorinator? Thank you!
     Reply


?     Asked on 5/16/2019 by Maria Durso

We have an AQL-PS-(4/8/16)-X288 and the main panel is nonfunctioning (just emits a periodic beep). We are currently able to operate the pool using the wired remote display/keypad. Any idea whether this is the part I might need to get the SmartControl Control Center up and running?
 Reply

A  Answered on 5/18/2019 by InyoPools Product Specialist Lennox H.

Hi, Maria. Since you're still able to use the wired remote control, your main pcb might still be good and the local display is the issue.
 Reply


?     Asked on 2/26/2019 by John

In comments below you've said that the GLX PCB PRO is not compatible with the older AquaLogic and in a later post said that it is??? Can you add the GLXPCBPRO to the older aqualogic and get aquaconnect connectivity? Which one is correct?
 Reply

A  Answered on 2/27/2019 by InyoPools Product Specialist Lennox H.

Hi, John. The GLX-PCB-PRO main PCB will allow you to upgrade the AquaLogic system to use the AquaConnect.
 Reply


?     Asked on 10/19/2018 by Jeffery

I have motherboard G1-06608M-1. It stopped keeping day & time programming. I wouldn't mind upgrading to also allow connection of pool equipment to iPhone if I have to replace motherboard anyway - what would be best fit? I have Hayward Pro Logic system
 Reply

A  Answered on 10/31/2018 by InyoPools Product Specialist Joe S.

Yes you would need AquaPlus / ProLogic Main PCB - All Date Code/Versions - GLX-PCB-PRO plus Wireless Antenna Base - AQL2BASERF plus Aqua Connect Home Network - AQCOHOMENET.
 Reply


?     Asked on 9/22/2018 by Ryan

Will this board Glx-pcb-pro work on an older aqualogic system with a glx-pcb-main? Trying to upgrade to use aqua connect. Will my current keypad work? It’s a ps-8. Hayward tech support tells me I’ll have a comm error but I have been reading conflicting things online. I do have a stand alone heater button as well on the control panel.
 Reply

A  Answered on 9/25/2018 by InyoPools Product Specialist Lennox H.

Hi, Ryan. Replacing the AquaLogic GLX-PCB-MAIN with GLX-PCB-PRO will allow you to use AquaConnect. 
 Reply


?     Asked on 7/7/2018 by Charlie Hardaker

Good Afternoon, We have a Aqua Plus Goldline Controls Pool Pump and from my research and recommendation from a pool mechanic we need a new mother board. Would this one work for our system? Please advise. V/R, Charlie Hardaker
 Reply

A  Answered on 7/7/2018 by InyoPools Product Specialist Lennox H.

Hi, Charlie. Yes, this replacement Main PCB - GLX-PCB-PRO is compatible with your AquaPlus controller. 
 Reply


?     Asked on 6/28/2018 by Brian

What is the benefit of this board -vs- Part # GLXPCBMAIN?
 Reply

A  Answered on 6/28/2018 by InyoPools Product Specialist Lennox H.

Hi, Brian. This Board will allow you to upgrade your firmware to 4.20 which will give you the capability to use any of the Turbo Cells, the latest wireless devices along with HomeConnect. These features and upgrades are not available with GLX-PCB-MAIN. 
 Reply


?     Asked on 5/28/2018 by rob

i have a goldline aqua plus with 4 breakers. My salt reading shows 2700 ppm and low salt indicator check system light is on. water sample at store indicates a salt level of 4300 ppm. what could cause the different reading? store test also had 4300ppb phosphorous , not sure if that is significant
 Reply

A  Answered on 6/8/2018 by InyoPools Product Specialist Megan C.

The cell or the main PCB could need to be replaced. Here a few guides that you may find helpful. How To Recalibrate the Salt Level on a Hayward Aqua Rite and How To Know When a Salt Cell is Bad - General
 Reply


?     Asked on 5/26/2018 by Dino Lopez

I have an AquaLogic system which was probably installed in 2005. I have read that the mother board GLX-PCB-MAIN is the replacement part but is not compatible with the Aquaconnect. In other posts I've read that the mother board GLX-PCB-PRO can be used to replace my old mother board for the Aqualogic and I can use the aquaconnect. But now in reading your posts you say that the boards aren't compatible?
 Reply

A  Answered on 5/28/2018 by InyoPools Product Specialist Lennox H.

Hi, Dino. You will need the AquaLogic/ProLogic Main PCB and AquaConnect Kit - GLX-PS-AQC to make it compatible. 
 Reply


?     Asked on 5/10/2018 by

I have an Aqua Logic Salt Generator that was installed in 2005. I am getting a No Cell Power alert again and the solder point on the back is showing a burned connection. The current mother board is green and is different than the Blue Board that I have found on line. Is the blue board the new product and will it work with my older unit?
 Reply

A  Answered on 5/12/2018 by InyoPools Product Specialist Lennox H.

Hi. The AquaLogic Main PCB - GLXPCBMAIN is the current style PCB for the Aqua Logic controller. 
 Reply


?     Asked on 2/6/2018 by DUKE

I HAVE A PL-PS-8 hayward pro logic 090007-446-01 Is this the right replacement board? Thank you, Duke
 Reply

A  Answered on 2/6/2018 by InyoPools Product Specialist Lennox H.

Hi, Duke. Yes, this the correct main pcb for the ProLogic PL-PS-8. 
 Reply


?     Asked on 2/3/2018 by Amanda

I have the Goldline Pro Logic PL-P-4 that is stating "No Cell Power". Pull out the board, changed fuses, and checked back of board for soldering problems and board is looks great. I was wondering if I need to change the whole board or is there a part I could change on my current board? Thank you!
 Reply

A  Answered on 2/5/2018 by InyoPools Product Specialist Lennox H.

Hi, Amanda. Unfortunately, you will have to replace the entire board. 
 Reply


?     Asked on 7/28/2017 by

I have a Aqua plus installed Pre 2009 and was wondering what firmware was available then. Friend purchase a generic T-Cell 15 and says requires Firmware 1.50 or higher. Was wondering if would work. He replaced his system with a competitors and i was wanting to purchase if compatible. Thanks.
 Reply

A  Answered on 7/29/2017 by InyoPools Product Specialist Lennox H.

Hi, The TCELL15 is compatible with the AquaPlus controller. 
 Reply


?     Asked on 7/19/2017 by Tom

I'm replacing my T-cell-3 and the instructions say the system must be 4.10 or newer, my system is 3.10, do all current cells, 3, 9, 15 require 4.10 or newer? Do I need to replace my pcb? If so would PL 7100 work, or is that strictly aquarite?
 Reply

A  Answered on 7/22/2017 by InyoPools Product Specialist Lennox H.

Hi, Tom. If you currently have a TCELL3 then it should be compatible with your controller.  The T-CELL-15 is the only size that can be used with the lower firmware. You will need to replace the PCB in order to get the latest firmware. The PL7100 PCB is only compatible with the AquaRite controller. 
 Reply


?     Asked on 7/18/2017 by Wayne Evans Sr

I have a Hayward Aqua Plus about 8 years old I replaced the cell with a Hayward T-15 this year however at 100% clorination and pump running 24/7 it will not make enough chlorine to maintain a level when you check it. If i catch a sample at the outlet back to the pool it shows its making some cholrine. Salt level is 3100 and all tests in normal range. It is showing the voltage going to the cell on the diagnostic screen like it is working. Could the control board be bad?
 Reply

A  Answered on 7/19/2017 by InyoPools Product Specialist Lennox H.

Hi, Wayne. I would recommend checking the Cell Configuration setting to make sure that the correct size cell is selected. If the board is bad it will give you an error message of some sort. 
 Reply


?     Asked on 7/11/2017 by Laura

We had a transformer blow on us. The electric company fixed it but our pool has not gotten power since. We had an electrician come out and check it and was told that power was getting to the pool. Do you think it is a circuit board, control panel display or both? We have a Hayward Goldline Pro logic control panel with a pl-ps-4 display.
 Reply

A  Answered on 7/13/2017 by InyoPools Product Specialist Patrick P.

Hi Laura, I would start with this Main ProLogic PCB as this normally the part that goes bad.
 Reply


?     Asked on 5/23/2017 by Bob Jones

I have a pool, installed in 2008. I have the Pro Logic Automation and Chlorination, Goldline Control, Model PL-P-4. I replaced my salt cell last year and shortly afterwards my PC Board now reads "No Cell Power 2". I believe I need to replace the PC Board within the control unit. Do you agree and what is the current part number needed to replace this board. Thanks, Bob
 Reply

A  Answered on 5/28/2017 by InyoPools Product Specialist Stacey M.

Hello, Yes I would agree, but before doing this I would run diagnostic with the manufacturer it the unit just needs to be recalibrated.
 Reply


?     Asked on 5/11/2017 by Magdalena

Hello, I have a Agua Logic control panel and is working on everything else's except the chlorinator it does not work , do I need a new Aqua logic PCB Main Circuit Board Replacement a and which is the part number?
 Reply

A  Answered on 5/12/2017 by InyoPools Product Specialist Lennox H.

Hi, Magdalena. The problem could be the PCB or the cell. Before purchasing any parts I would recommend troubleshooting the unit to find out where the problem is at. The replacement PCB p/n is GLXPCBMAIN.
 Reply


?     Asked on 11/11/2015 by john

Hi, I need a PCB for my Aqua Plus Automation and Chlorination system. It's model # is PL-xx-xx. The manual that came with it is for PL-Plus and PL-Plus-20. What circuit board will be compatible? Thanks, John
 Reply

A  Answered on 11/11/2015 by InyoPools Product Specialist Joe S.

Hello John, the glx-pcb-pro will be the board you need. You can always call Hayward and provide them with the serial number off the unit for any part needed as well.
 Reply


?     Asked on 9/12/2015 by Gabriel

I have a Aqua Logic (AQL-PS-8) which needs a new main circuit board. Can i use the glx-pcb-pro instead of the glx-pcb-main? If so, what is the advantage ("pro" costs more, so i assume there are more features)?
 Reply

A  Answered on 9/16/2015 by InyoPools Product Specialist Lennox H.

Hi Gabriel, The correct PCB Board that you will need for the Aqua Logic AQL-PS-8 controller would be the Aqua Logic Main PCB Board (GLX-PCB-MAIN). The GLX-PCB-PRO is not compatible with the Aqua Logic system.
 Reply


?     Asked on 7/12/2015 by Larry

I have a 6 year old Goldline Aqua Plus that the timer stopped working. I have to turn on the filter pump manually every day. The circuit board has PN: G1-66008N-1 on it. Do I need a new board to fix this, if so what is the part number I need to order.
 Reply

A  Answered on 7/12/2015 by InyoPools Product Specialist Patrick P.

Hi Larry, Yes based on your issue it is most likely a bad circuit board and this would be the corect replacement circuit board for the Hayward Goldline Aqua Plus.
 Reply


?     Asked on 7/1/2015 by David

GLX-PCB-PRO How long is the warranty and Is it pro-rated by year?
 Reply

A  Answered on 7/2/2015 by InyoPools Product Specialist Lennox H.

Hi David, The PCB-main, Pro Logic, All Versions, All Date Codes (GLX-PCB-PRO) comes with a 1 Year Warranty, no proration for the warranty period.
 Reply


?     Asked on 6/18/2015 by Jeff

I have a AQUA PLUS MODEL PL-PLUS, PL-PLUS-20 MODEL WOULD THIS BOARD BE CORRECT FOR ME TO USE? THANKS
 Reply

A  Answered on 6/18/2015 by InyoPools Product Specialist Patrick P.

Hi Jeff, yes this board works for both the Hayward / Goldline AquaPlus as well as the ProLogic systems, so this would be the board for you.
 Reply


?     Asked on 5/19/2015 by Tom Cady

What is the software version on this board?......4.30?
 Reply

A  Answered on 5/22/2015 by InyoPools Product Specialist Patrick P.

The current version we are shipping out as of the time of replying to this question is Software version 4.45, which is backwards compatible to all older versions.
 Reply


?     Asked on 5/12/2015 by Dan clark

I have a goldline PL-p-4-X-288 smart control used by blue haven pools . I need a control board. Please advise if you carry one . Thank you!
 Reply

A  Answered on 5/12/2015 by InyoPools Product Specialist Joe S.

Hello Dan, Yes if you have a Prologic PLP$ system then the GLX-PCB-Pro will be the correct board for your system
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver

Board was displaying an error

Written on 11/21/2019 by Guest

The repair was very straightforward, remove connectors (I took a picture for reference), remove 4 screws and unclip the board. New board was a perfect replacement. I connected everything back, setup the wireless again and I was back in business.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 0  out of 5 stars)
0 Rating
5 star:
 
(0)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)