I have a Hayward H250ED2 pool heater that needs a new control board as the sun has almost completely destroyed the plastic buttons on the control board. What is the difference between the HAXCPA1932 and the HAXCPA3253 besides the price. The circuit board is still OK on my control panel just the push buttons barely work.
Reply
Hello Arthur. I spoke to the Hayward Technical line and they told me that HAXCPA1932 is the control board, bezel and key pad. The HAXCPA3253 is the control board, bezel , keypad AND the piece of sheet metal used to hold it in. He was unsure as to why the one with less cost more. But did assure me that for a 250DS, the best value is the HAXCPA3253
Reply
Will the HAXCPA3253 work for my H200PED2 Heater, Serial # 30625037?
Reply
HI Dan, The correct part will be the Control Panel 200DS H-series ED2 (HAXCPA3203) for your H200PED2 heater.
Reply
Will bezel and control panel part# HAXCPA3253 work on y Hayward heater model H250PED2?
Thanks for the help,
Jerry Stewart
Reply
Hi Jerry, The Control Panel 250DS H-series ED2 (HAXCPA3253) will be the correct panel for the H250PED2 heater.
Reply
Will this part fit my existing control panel # H200ED2?
Reply
Hi Tom, This part will not fit the H200ED2 unit, you will need p/n HAXCPA3203.
Reply
I have a Model H150ED2 Hayward Heater.
Is Control Panel 250DS H-series ED2 ( HAXCPA3253 ) the control panel I need.
Thanks,Mike
Reply
Hi Mike M. The correct control panel for the H150ED2 heater is HAXCPA1932.
Reply
Is this the main control board for an H400ED2?
Reply
Hi, Jeff. The replacement control panel for the H400ED2 is p/n HAXCPA3403.
Reply
I have a Hayward Pool Heater H series. The control board won't move to spa or pool for heating. what should I do? Hayward H series model# H250PED2
Reply
Hi. If the unit is working but not switching to pool or spa mode the control panel is the issue and would need to be replaced.
Reply
Hayward H250PED2 heater.
Is the keypad available by itself? My control board is fully functional.
Reply
Hi, Rick. The H-Series Control Bezel Assembly - HAXCPA1932 is available separately.
Reply
I have a Hayward heater model: HD300ED2. My control panel switches from standby to spa/pool and the pool temp. is displayed, but i cannot increase or decrease the water temp that I want AND the heater does not ignite (after 3 tries). I do smell gas. What do I need to replace?
Reply
Hi, Bob. You will need to replace the H-Series Control Bezel Assembly - HAXCPA1932 based on your unit's model.
Reply
I have a Hayward gas heater h250ed2 model that needs new control panel. What part no.? Thanks,mm
Reply
The correct part number for the H250ED2 control is the HAXCPA3253
Reply
I have a Hayward H300ED2 pool heater I'm pretty sure the control panel is shot. I cant navigate the temp up or down without it flashing and when it reverts back to steady the number is at current pool temp (62). It fires for just 15 seconds then goes out.
Reply
Is your heater short cycling? Hayward tech service is 908-355-7995
Reply
From the info you gave it would appear that the control is working correctly. It will display the actual tempo when not flashing. When you press the temp button it will flash to tell you are in set temp mode. It would appear you have a different error happening after it fires up.
Reply
Is the outside panel available without all the pieces underneath?
Reply
Hello. According to the manufacturer, Hayward, the Control Panel 250DS H-Series ED2, HAXCPA3253), does not have individual component parts availability. It is only available as a complete unit. Attached please find an exploded parts diagram for the Hayward H-Series Electronic ED2 Heater. Hayward H-Series Electronic ED2
Reply
