Part # UQS1152R
Warranty 1 Year
Dimensions 14.5" L x 7" W x 7" D
Alternate Part #'s 12041, 12090, A100FLL-Y, AE100FHL-YS, C48L2EM101A1, C48L2P104, C48L2P107, K48L2P104B3, SQS1102R, UQS1152R
PLEASE NOTE: UQS1152R IS NO LONGER AVAILABLE -REPLACED BY SQS1102R (FULL RATED 1.0HP)
Voltage 230, High Speed HP = 1 1/2 Low Speed HP = 1/4, Max Amps @ High HP = 7.8 Max Amps @ Low HP = 3.0, Dual Speed, Square Flange, RPM @ High Speed = 3450 RPM @ Low Speed = 1725, Threaded Shaft, Frame = 48Y Used on the following models: Sta-Rite Max-E-Glas, Max-E-Glas II, Dura-Glas, Dura-Glas II, Dyna-Glas, Dyna-Max Pentair Whisperflow, Pinnacle and Anthony AR2 Series.
I have a Dura-Glas motor C48L2P104. I see the correct pump to replace with, on your site. On my old pump, how do I remove the impeller that's on the end of the shaft, to put onto the new motor? Thank You
I have a jandy hp plus 1 1/2, - 2 hp pump put in 2014. I want to replace the motor. the part number on the motor is 0-193990-07 but that doesn't match anything on your web site. can you help. I already bought a whole replacement pump but goofed and bought a one speed.
Hi Gary, the proper replacement motor your 0-193990-07 motor is the B2983 Dual Speed Replacement Motor and we have that motor in stock.
Will this replace WF-26/PART #012518
Hi, Robert. This UQS1152R Motor which has been replaced by the SQS1102R will convert the WF-26/011773 Pump to the WFDS-26/012518.
I have a Blue Haven Pool and the pump motor has the following AO Smith SP3210Z2Me and a part number of 7-K56AA23A04-05. I am trying to find a replacement motor for it. It is a 1.5hp 2 speed pump. It is a 3450/1725 RPM. FR is Y56Y. Type is CXCP. Form is KJM. Amps 8.5/1.5. Can you tell me which motor is correct.
I need to replace the motor on my Hot Tub the Model is Dura Glas H/1 C48L2P104. Which is no longer available, do you know which motor replaces it?
Good afternoon Jack, You are looking for a A.O. Smith 1 1/2 H.P Square Flange Dual Speed Up Rate Motor - UQS1152R You will also need a seal kit with the o-rings and the shaft seal Tune Up Kit Sta Rite Dura Glas & Max E Glas Pump 1998 To Present - GOKIT54 If there is anything else I can assist you with let me know.
Is this the motor to replace a Sta-Rite Model P2RA5F-182L in-ground pool pump?
Hello, yes this is A.O. Smith 1 1/2 H.P Square Flange Dual Speed Up Rate Motor - UQS1152R for a P2RA5F, please make sure to check your product specs for this dual speed motor. I would highly recommend a GOKIT to replace all seals.
I need replacement motorMod.K48L2p104b3 HP 1.5,1/4 What 2 speed will fit?
Yes, that would be the correct replacement motor according to the part number you provided.
Is this the correct motor for pentair superflo 1.5 hp
I am replacing a 30yrs old A.O. Smith motor on a hot tub. Motor Mod#C48L2P104. It is a two speed motor and my question is, what are the wiring terminals for the low speed/ high speed connections. Thank you.
Hi Ron, You can find the wiring terminals via the UQS1152R Dimensional Drawings.
I have a Jandy Plus HP pump with the overheating cheap replacement motor. I want to replace this motor but I don't have the exact model on the pump or the original motor. I was told I have to take the pump apart and find out which impeller is in it. Will there be an obvious part number on the impeller if I do this? The original pump was installed in 2010 and was 1 1/2HP 2-spd. This cheap motor is 1 HP 2-spd and shuts off on high speed and doesn't provide flow for the salt gen on low speed.
Hi Lauren, Yes when you remove the impeller there will be a part # embossed into the plastic of the impeller, once you get the part # then email us and we will let you know which model you have. I think I know the reason why your second motor burned up so quickly. When you went down from 1-1/2 HP to 1 HP if you did not down size your impeller to 1 HP then the 1 HP motor is going to be working too hard as it still has the 1-1/2 HP impeller. Basically the 1 HP motor is trying to do the work of a 1-1/2 HP motor. When you purchase the new motor make sure that the HP rating of the impeller matches that of the motor. We can help you figure this out once you supply the impeller part # information.
I'm trying to replace the motor on my pool pump but all these numbers and abbreviations on the motor label are really confusing me. What do they mean?
Replacing a pool pump motor is not as difficult as it seems. You can try looking here. If you need help figuring out what the information on your label means. If you are still having difficulty figuring it out you can call us at our toll free number or you can send us a photo of your motor label here.
How can I tell whether or not my motor is a dual or single speed?
Most dual speed motors will have a toggle switch that will allow you to adjust the motor speed to either high or low. Another way to tell if your motor is dual speed is by looking at the RPM's on the motor specifications label. If there are two RPM's listed such as: 1725/3450 then motor is dual speed. If there is only one RPM, then motor is single speed.
Can you direct me to the proper hi low switch for this motor?
Unfortunately the manufacturer does not offer the switch for the 2 speed 220v motors any longer. If you already have a 220 volt timer (on/off) you would need an Intermatic T106R to switch from high to low speed. If you do not have a timer currently you would need the T10604R which is a 220v on/off timer and a high/low timer.
Why should I purchase a Tune Up Kit?
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Why do I need to purchase a new shaft seal?
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
What is Service Factor?
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Can you replace single speed pump motor with dual speed pump motor?
Yes but you can't go with a higher HP than the single speed motor. For example if you have a 1 HP single speed you cannot go with a 1.5 HP dual speed motor; you would be able to use a 1 HP dual speed motor. Customer would need to purchase a toggle switch or timer to switch from high speed to low speed.
(5 out of 5 stars) Pump motor replacement
Reviewed By: Jake ()
Pros: easy to find replacement parts
I have a 25 year old hot tub with Sta Rite hardware. The original pump failed and I purchased this pump as a replacement. It was very easy to install and it works great. It was very easy to find this replacement on INYO pools website, I will definitely use it for any other hot tub needs.