Tune Up Kit Sta Rite Dyn Glas & Dyna Max - GOKIT47

$37.95

IN STOCK
FREE SHIPPING

Part # GOKIT47

By Aladdin

  4.41 Average  

Details

Top

Part # GOKIT47

Product Description

INYOpools highly recommends replacing the shaft seal, o-rings and gaskets when replacing your motor, if you use your old shaft seal it will not mate up properly with the new pump and may leak. The best value is to go with one of INYO's tune up kits which include the shaft seal and all O-rings, gaskets and lubricant for your pump.

This Tune Up Kit Works on These Pumps:

  • All Sta-Rite Dyna Glas & Dyna Max 1/2 HP - 3 HP single and dual speed models.
  • All Sta-Rite MPR & MPE Series Pumps 1/2 HP - 3 HP single and dual speed models.

Tune Up Kit Includes:

  • Motor Shaft Seal
  • Seal Plate O-Ring - J Series
  • Seal Plate O-Ring - Dyna Glas
  • Diffuser O-Ring
  • Lid O-Ring
  • Lubricant

For More Pool Pump Motors

Top

?     Asked on 8/5/2016 by Susan

I purchased a USQ1102 replacement motor for a Sta Rite Dyna-Glas pump. Then I ordered the wrong tune up kit. I see now that the correct kit is Gokit47, but it does not appear to have the square gasket included. Which gasket should I order?

A     Answered on 8/10/2016 by InyoPools Product Specialist Lennox H.

Hi Susan, The Sta-Rite Dyna Glas/Max pump does not have any square gaskets. It's possible that over time which happens the o-ring becomes flat causing it to appear square.

?     Asked on 7/22/2016 by Omer Malik

I am looking for the rebuilt kit for MPRA6G-155L. Will this kit fit. On a somewhat related note, I am looking for a capacitor for the motor as well. The motor is : A100GLL.

A     Answered on 7/24/2016 by InyoPools Product Specialist Lennox H.

Hi Omer, Yes, this kit can be used with the MPRA6G-155L pump. The A100GLL motor has a 20 MFD 370 Volt Run Capacitor (RD-20-370) and a 36-43 MFD 220-250 Volt Start Capacitor (BC36M-250-S).

?     Asked on 6/25/2016 by jack nemeth

I have small pcs of plastic circles aprox. 1/4" round in my filter? Sta-rite dyna glass PLD36what parts do i need?

A     Answered on 6/30/2016 by InyoPools Product Specialist Lennox H.

Hi Jack, I'm not sure exactly which part you're referring to. Click link >Sta Rite System 2 MOD Media & MOD D.E. PLM & PLD for the available PLD parts and Sta-Rite Dyna-Glas and Dyna-Max for available Dyna-Glas parts.

?     Asked on 3/28/2016 by

I have a Sta-rite Dyna-Glas pool pump, model # MPRA6F-148L. It has a small leak from the seal area. Will the O-ring from this kit fit my pump?

A     Answered on 3/28/2016 by InyoPools Product Specialist Andy O.

Hello- The GOKIT47 Tune Up Kit Sta Rite Dyn Glas & Dyna Max is the correct kit for your pump, the o-ring in the kit will work with your pump.

?     Asked on 2/13/2016 by Evan

I have a Sta Rite Super Max 1.5HP, 1.1SF. I found my replacement pump on your site, but which service kit or parts do I need to go with it?

A     Answered on 2/16/2016 by InyoPools Product Specialist Andy O.

Evan, They do not have a tune-up kit for the supermax, but the most important seal would be the shaft seal, which is part# 5250-210 Pump Seal 200, Heavy Duty PS3867. All other o-rings would have to be purchased separately.

?     Asked on 1/31/2016 by Jimbo

Will this go kit work on my Dyna-glas 1HP MPFA6E-146L pump? Its a very old model.

A     Answered on 2/2/2016 by InyoPools Product Specialist Lennox H.

Hi Jimbo, The Sta-Rite Dyn Glas & Dyna Max Tune Up Kit will work with your Dyna-glas 1HP MPFA6E-146L pump

?     Asked on 7/8/2015 by

My sta rite MPRA6E-147L pump started to make a louder noise then usual so I looked at it and found that it is leaking a little bit of water from the bottom of it. Could the leak be the cause of the noise?

A     Answered on 7/11/2015 by InyoPools Product Specialist Patrick P.

Yes normally a leak can cause to seal failure which will cause the bearings to go bad in the motor. A sign of the bearings going bad is that the motor starts to run loud.

?     Asked on 10/15/2014 by Guest

My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?

A     Answered on 10/15/2014 by InyoPools Product Specialist Patrick P.

The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.

?     Asked on 2/13/2012 by Guest

I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!

A     Answered on 2/13/2012 by InyoPools Product Specialist Patrick P.

You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.

Top

Review Summary

  (Average 4.41 out of 5 stars)
10 Rating
5 star:
 
(5)
4 star:
 
(4)
3 star:
 
(1)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews