Part # SPX1600Z2
Dimensions 3.75" L x 1.5" W x 2.25" D
Alternate Part #'s 35B1109, 60758, HAY1012020, SP1600Z2, SPX1600-Z-2
Original Hayward Super Pump shaft seal also used on the Hayward Max-Flo, Super II and Super Spa pumps. Replace your shaft seal to prevent leaks and protect your pool pump, especially important when replacing the pump motor.
I HAVE A salt water pool. Do I need to get a pump seal especially for salt water, or will the SPX1600Z2 (OEM) seal work in salt water applications?
Hi, Billy. The OEM shaft seal will work in a saltwater application.
water leaking from bottom of pump also loss in suction, psi is down about 5psi. suction is weak during vacuum. my question, would you start by replacing the shaft seal first?
Hello, I would recommend inspecting the lid gasket first. If the pump is leaking, it can be the shaft seal or the housing gasket.
I have a pump SP-3110X15. I replaced all the o-rings but is still leaking out the bottom at the vent channel of the Seal Plate. What do you recommend I replace next?
Hi, Chris. Sounds like you'll need to replace the Pump Seal - SPX1600Z2.
do you have a video on how to install the ceramic and spring seal /
Hello, there is a video How To Replace a Pool Motor Shaft Seal.
Is this the correct seal for SPX2621X25 Superpump 2.5 HP?
Yes, the SPX1600Z2 is the correct shaft seal for your Super Pump.
I have a ca. 2003 Super Pump in need of a seal replacement. Model number is C48L2N134B1 SP-1610-Z1-M 1.5 HP Made in Mexico Will the SP1600Z2 work on this unit?
Hi Dan, Yes this would be the proper seal replacement for your Hayward Super Pump.
How do I know which seal kit is the right one?
Hi, If you can provide us with the make and model of the pump we can locate the correct seal and parts.
I have Max-Flo pump SP1615z-1 MXBK 7-186856-01 what is correct seals #. Thank you
when replacing the seal assembly replacement on a hayward super 2 what is the correct orientation to put these on.
You can put a very small amount of silicone lube on the rubber parts but none on the white ceramic part, just the rubber parts.
Hi there, I have a Hayward Pump, however its missing the pump label, stating the Hayward model. Looking at pictures online, Ive identified it as a Hayward Max-Flo Pump, self priming pump. The pump motor does have a label that reads HAYWARD MAX-FLO PUMP. In the past I ordered a strainer basket model #2800. The pump leaks underneath it, where the the motor meets pump. Id like to order a complete seal kit, including shaft seal, to correct this. Can you provide assistance ? Thanx. Frank
Hi, Frank. The Hayward MaxFlo Tune Up Kit - GOKIT1 is the kit that you will need for the Hayward MaxFlo pump that includes all the gaskets and pump shaft seal.
Is the shaft seal for the Hayward super 11 pump ceramic?
It is a two piece seal. One piece is the ceramic part and the other is the spring part that goes up against the back of the impeller.
My pump is a Hayward SP2607X10, what is the correct seal for this pump?
Hello, this is the correct pump seal if you would like the Tune Up Kit Hayward Super Pump - GOKIT3 it comes with seals, and orings for whole pump.
I have a Hayward Super pump model # C48K2N143B1 - is the SPX1600Z2 the correct seal?
Hi Diane, Yes, this is the correct pump shaft seal for the Hayward Super Pump.
I have a Hayward RS 2000- which shaft seal would I use?
Hello, the correct shaft seal for the RS 2000 would be the SHAFT SEAL 201 (GENERIC) - AS-1521.
i have a hayward pump model #sp2607x10 will this fit? model # on motor is ust1152
Hi Dave, Yes, this pump shaft seal will work with the SP2607X10 pump.
My pump is a Hayward Model SP2607x10. the motor is a new motor from your company item number UST 1102. what parts should I order for the shaft seal, gaskets etc. to stop water from leaking? Thank you
The correct gasket replacement would be the Tune Up Kit Hayward Super Pump GoKit3.
My new A.O Smith 1 hp round flange up rate motor item # UST1102 is leaking water. What parts shaft seal, gaskets etc. do I need to stop the leak. Thank you
You will need to identify the pump you own to determine the correct shaft/pump seal part you would need to replace bad seal. The pump information would be located on the front half of the pump the motor is attached to.
need to replace shaft seal on hayward rs 1500 series 1 1/2 -2 hp serial # 21111205084817 will this hayward shaft seal fit my pump? thank you
Yes this is the correct shaft seal for the Hayward - Leslie's RS1500 Pump.
I am replacing the motor for my Hayward Super pump 1H.P. Model # C48K2N143B1 Is this the correct shaft seal for this motor?
Yes, the the SPX1600Z2 is the correct shaft seal for the Hayward Super Pump.
I have a Hayward pump and want to change the seal, is there more than 1 size
Dean, Yes not every pump model has the same shaft seal. We would need to know the specific model of the pump to find the correct shaft seal for your pump.
I have a Hayward super pump and had a drip where the motor mounts into the pump housing. I replaced the housing gasket and it is still dripping. Could the problem be something else. Any help would be great. Thanks Mike
I have a Hayward 1 1/2 horse super II pump will this shaft seal fit my pump or do I need the model number to order it
Hi Mike, this is the correct shaft seal for a Hayward Super II Pump (no model # needed).
1 to 2 hrs
Screwdriver, Nut Drivers, Socket Set, Wrench Set, Adjustable Wrench