Hayward Skimmer Weir Assembly Kit - SPX1070KHR



Part # SPX1070KHR

By Hayward Pool Products

  5 Average  



Part # SPX1070KHR

Dimensions 8.6875" L x 5.625" W x 1" D

Product Description

This is a replacement for the Hayward Pool Skimmer SP1082 & SP1071 Weir.


  • Length: 8-7/16"
  • Width: 5-1/6"

?     Asked on 10/27/2017 by Fancy

Is there a universal type spring loaded weir door which will be a suitable replacement for the Hayward SP1070K weir door - during a pool re-plastering the workers damaged one of the lower skimmer corners of the front housing breaking a couple tabs that help hold the SP1070K weir door in place off - I'd like to have the damage epoxied but in so doing would not be capable of accommodating a typical SP1070K weir door - as an alternative, I am seeking a suitable spring loaded type weir door.

A     Answered on 10/31/2017 by InyoPools Product Specialist Lennox H.

Hi, Fancy. The Swimquip Weir 8-3/8" - R240067 can be used as a replacement for this Hayward Weir Kit - SPX1070KHR

?     Asked on 7/19/2017 by

How do install the Hayward Weir assy Kit SP1070-K or equivalent I would have to purchase in replacement of a broken one? Mine doesnt stay in its place due to a broken pin? What would be the cost to buy it if available???

A     Answered on 7/22/2017 by InyoPools Product Specialist Lennox H.

Hi. Specific installation instructions are not available for this weir. If the tabs for the hinge is ok you can snap the new replacement weir back in place or remove the old weir with the hinge and install the new one. 

?     Asked on 5/18/2016 by Joe

I need a replacement part for the skimmer on my in ground pool. The part number on the (I'll call it the door - I think you call it a weir). Thew part number on the unit that came off - the tab that held in place broke - is SP1070-K. Do you have such an animal or a replacement for it.

A     Answered on 5/18/2016 by InyoPools Product Specialist Alan M.

Hello Joe, The Hayward Skimmer Weir Assembly Kit is the door, or flap, to the skimmer. This is a complete weir assembly that includes the door and the base the door is attached to. No assembly of the door is required.

?     Asked on 6/7/2015 by Vicky

My skimmer flap ( not sure if that's the right term for it) has broken. It's a SP1070-K. I see that Hayward no longer makes these. Which one should I get as the replacement?

A     Answered on 6/7/2015 by InyoPools Product Specialist Patrick P.

Hi Vicky, The Hayward Skimmer weir assembly kit (SPX1070KHR) on this page is the correct replacement for your SP1070K skimmer flap.

?     Asked on 6/6/2015 by tom

My door broke off, how do i remove the old bracket and replace with a new one?

A     Answered on 6/6/2015 by InyoPools Product Specialist Patrick P.

Hi Tom, I ran across this Post on Removing and Repairing an Old Weir which should be of help as it explains your situation in detail.

?     Asked on 4/2/2015 by Pamela

Do I need to order a replacement flat bar separately? The slots on the door have become too large and it will not stay attached to the bar.

A     Answered on 4/2/2015 by InyoPools Product Specialist Lennox H.

Pamela, this part will come with the weir and the part that it attached too (flat bar). You'll get both parts that appears in the photo.

?     Asked on 3/29/2015 by Ken

where does the bumper pad go on the SPX1070KHR kit ?

A     Answered on 3/30/2015 by InyoPools Product Specialist Lennox H.

Hi Ken, The bumper will go at the top of the skimmer. It acts as a stopper for the weir.

?     Asked on 4/24/2013 by Guest

Is the Hayward SPX1070KHR the replacement for the SP1070K?

A     Answered on 4/24/2013 by InyoPools Product Specialist Patrick P.

Yes, part number SPX1070KHR is the replacement weir for the SP1070K.

?     Asked on 8/13/2012 by Guest

The flapper that broke off my skimmer is a model SP1070-K. Do I need a replacement kit or can the flapper be replaced?

A     Answered on 8/13/2012 by InyoPools Product Specialist Patrick P.

Hayward has discontinued the SP1070K and now only sell the SP1070KHR weir kit which does include the SP1070K weir / flapper.

?     Asked on 8/8/2012 by Guest

Could I use the SPX1070KHR in place of the SPX1071K skimmer weir? I have the SP1071 Hayward Skimmer, the two weirs look similar but have different prices.

A     Answered on 8/8/2012 by InyoPools Product Specialist Patrick P.

The Hayward SPX1070KHR and SPX1071 are not interchangeable. The Hayward SP1070 Skimmer requires a hinged weir door and the SP1071 Skimmer uses a spring loaded door.


Review Summary

  (Average 5 out of 5 stars)
2 Rating
5 star:
4 star:
3 star:
2 star:
1 star:

The Most Helpful Review

The Most Recent Reviews