Part # P1101
Heavy Duty Outdoor Timer P1101 Designed for pumps up to 1 HP with a standard 3 prong plug configuration.
This Portable Outdoor Timer is specially designed to control the filter pump of a portable pool or spa. They can also be used to turn ON and OFF outdoor decorations, engine block heaters and other appliances - indoors or outdoors. Designed for pumps up to 1 HP with a standard 3 prong plug configuration. PLEASE NOTE: This timer does not have GFCI. If you need a timer with GFCI, please see the Intermatic P1161.
Case - 5" (12.7 cm) high x 5-1/2" (14 cm) wide x 3-3/4" (9.5 cm) deep.
Cord - 3 wire, outdoor grade, 22" long.
Timer - 24 hr. with 23-1/2 hr. maximum ON time.
Switch Rating - 15 Amp resistive or tungsten
Agency Approval - CSA/C-US
• Filter Pumps
• Air Conditioners
• Engine Block Heaters
Is this pump intended for use on an in ground pool?
This timer is designed to be used with an above ground swimming pool.
Do you have a timer for a 2 hp pump for above-ground pool with salt system?
Hi, Steven. We do not have an above ground pool timer that is specifically for 2 hp pumps. You will have to have it hard wired using one of these Pool Timers.
I am looking fo a outdoor timer for pool pump rated for 1.5 hp motor most intermatic outdoor timer are rated for 1 hp
Vito, We do not have a 115v plug in timer for a 1.5HP pump. We recommend an Intermatic T101P3.
Does this item have multiple receptacles? I need atleast two plugs for salt system and pump.
Hi, Victor. This only has one outlet plug so you will need two timers.
I have a 1-1/2 hp Pentair Sta-rite Dynamo pump ... what timer would you recommend?
If this is for an above ground pool, I would get the one with the GFCI, part number P1131.
How does the pump connect to the timer? does it plug in or does it have to be wired?
Hi, The pump plugs into this timer.
Does this item have an on/off switch?
Linda, This Intermatic Above Ground Pool 3 Prong Timer does have a manual ON/OFF switch.
How dose this run your pump?
This timer is designed to operate an above ground pool pump which has standard 3 prong plug and is 1 HP or less. The timer plugs into a wall outlet and then the pump plugs into the timer, you set when the pump turns on and off through the timer dial on the front of the timer.
How many times can this timer be set for on and off?
According to Intermatic's technical support, this timer can be set for four on/off settings.
I have a 1 1/2 HP Hayward filter, I need a timer box that I can connect to it. Will this handle it or do you have another timer that might?
This will only accommodate up to 1.0 HP pump. If this is for an above ground pool pump then you could use the following timer SP1500FT http://www.inyopools.com/Products/02200022032590.htm
(5 out of 5 stars) Good Timer!
Reviewed By: John from Warwick, NY ()
Pros: Reliable, Easy to operate
Cons: Mounting holes could be designed better
I installed this on my Hayward AG pump/filter as the only timer choices on the hayward pump timer were 24,18,12 and 6 hours. 6 hours was too short and 12 was too long. This timer will start and stop the pump whenever you want it to. It is easy to install, but the mounting holes could be designed a little better. It has been working flawlessly all summer.
(5 out of 5 stars) Cut down electric bill Timer
Reviewed By: Tom W. from Vermont ()
Pros: set it and forget it.
This timer really helped cut our electric bill. Our pool filter is pretty efficient so we only run it between 10am and 4pm. Except for the hottest days, this was sufficient to keep the pool clear and skimmed. We were really happy with this product.