Part # BN62
Part # BN62
Warranty 1 Year
Alternate Part #'s 10-184821-03, 10-184821-04, 10-184833-04, 184821, 184833, 184894, 186300, 42005, 5KCR39UN6098X, 7-184821-04, 8-184821-40, C1504, sph30fl2s
Century Flex-48 pump motors. Features: 12 & 3 O'clock conduit entries, non-reversible, through bolt mount, 3.5 In. shaft height, extra low running amps, two speed. Specifications: High speed - 3.0 H.P. Low speed - .38 H.P. Volts - 230 HZ - 60 RPM (high speed) 3600 (low speed) 1800 Full load amps - (high speed) 12.0 (low speed) 3.5 Frame - 48Y
Looking for replacement for AO Smith 7-182477-02. Will thisbwork?
Actually, the replacement motor is the model BN51.
have old ao smith spa motor need to replace do not know hp 230 v 2 speed 48y fr number on side plate we can read 7-193227 01
Hi, Doug. The BN61 motor is the correct replacement motor for Part # 7-193227-01.
Is this motor compatible with Hayward pool pump?
These can be used on Hayward spa or above ground pumps but are not commonly used at this strength.
I have the older version of this pump, the Emerson T55MWCCE-1208. What capacitors (start and running) can I order from you to replace the ones I have. After reading on your web site here it sounds like I have a bad capacitor. Thanks Tom
The bearings we carry are for Century/A.O. Smith motors not Emerson motors. The BN62 would be the replacement motor for that motor though.
what is the difference from a 48 frame to a 56 frame
Hi, The difference between a 48Y and 56Y frame motor is the diameter of the motor.
Which the tune-up kit is the correct one for WATERWAY 48F Executive Pump, 2-speed, 4.5HP, 230Volt, 12.0A/3.5A - 3421821-1A ?
Which Tune-up kit is the correct kit for this mortor ?
Danny- The tune up kit is based off of your pump housing and not your motor. What is the model of your pump?
Can you direct me to the proper hi low switch for this motor?
Unfortunately the manufacturer does not offer the switch for the 2 speed 220v motors any longer. If you already have a 220 volt timer (on/off) you would need an Intermatic T106R to switch from high to low speed. If you do not have a timer currently you would need the T10604R which is a 220v on/off timer and a high/low timer.
Why should I purchase a Tune Up Kit?
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Why do I need to purchase a new shaft seal?
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
What is Service Factor?
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.