Raypak RP2100 Heater 266,000 BTU NG MV - PR266AMN



Model # 009193

By Raypak

  4 Average  



Model # 009193

Warranty 1 year

Manufacturer Code PR266AMN

Alternate Part #'s 009193

Product Description



  • Dial control for temperature selection and heater settings

  • Capron resin headers prevent rust stains from harming pool surface

  • Plumb directly from provided 2" PVC threaded union

  • Smart microprocessor controls diagnostic read-out and continuously monitors operating status

  • Completely field serviceable

  • Small footprint

  • High efficiency

  • Guaranteed high wind reliability

  • Looks smart and works smart

  • 1 Year Warranty

  • Thermal Efficiency of 83% 


California Customers Please Note:  South Coast Air Quality Management District ( SCAQMD) Area of Jurisdiction REQUIRES a Low Nox Heater be installed.  The following 6 California Counties are affected:  Los Angeles, San Bernardino, Ventura, Orange, Riverside, & Kern. Installing a non-compliant heater in these counties will void the manufacturer's warranty and could result in a fine from your local code enforcement.    

Click here for RayPak Low Nox Heaters 

Elevation: 0 Ft. – 2000 Ft. Click Here for High Altitude Pool Heaters


Raypak Pool Heater DimensionsRaypak Pool Heater Dimensions

Raypak Heater Dimensions


Product Specifications

266,000 BTU
Digital Readout:
0-2,000 ft.
Heat Exchanger:
Special Feature:
Standard Emission

?     Asked on 9/4/2019 by

is this digital electronic and nickle

A  Answered on 9/5/2019 by InyoPools Product Specialist Joe S.

No, the model needed would be Raypak Heater 266,000 BTU's NG ELE W/ Cupro-Nickel Heat Exchanger - 014939

?     Asked on 5/12/2018 by RS

I have a RP2100, which I believe is the 266 KBTU model, but it only has 1/2" line. This one appears to require a 3/4". Is that right? Maybe I have enough pressure to make up the smaller diameter? Or am I missing something?

A  Answered on 5/15/2018 by InyoPools Product Specialist Lennox H.

Hi, RS. The gas line connection to the unit needs to be 3/4", that does not pertain to the actual pipe size. 

?     Asked on 8/11/2017 by Lee

what size of pipe is the natural gas connection on the Raypak 266000 BTU ng mv PR266AMN? Do you provide nipples and unions for the gas connection?

A  Answered on 8/17/2017 by InyoPools Product Specialist Joe S.

You will have to check with your gas installer. It will depend on the run from the meter to the unit. We do not provide any hardware for the gas connections. 

?     Asked on 7/24/2017 by Sandy Edenfield

Where can I find an instruction manual for a 2006 raypak millivolt n/g 266,00 BTU pool heater? How to I restart the pilot light?

A  Answered on 7/29/2017 by InyoPools Product Specialist Lennox H.

Hi, Sandy. Click this link >Raypak Owners/Instructions Manual< to download the manual for your unit.

?     Asked on 6/28/2017 by linda

how far does the pool heater have to be from the house - huntington ny

A  Answered on 6/29/2017 by InyoPools Product Specialist Joe S.

For U.S. installations, the point from where the flue products exit the heater must be a minimum of 4 ft below, 4 ft horizontally from, or 1 ft above any door, window or gravity inlet into any building. The top surface of the heater shall be at least 3 ft above any forced air inlet, or intake ducts located within 10 ft horizontally

?     Asked on 6/6/2017 by

Can this heater be converted from natural gas to propane?

A  Answered on 6/11/2017 by InyoPools Product Specialist Patrick P.

Yes you would need this Raypak Conversion Kit.

?     Asked on 6/2/2017 by ed

would this be suitable for a 30 thousand gallon pool

A  Answered on 6/6/2017 by InyoPools Product Specialist Stacey M.

Hello, This would be a suitable unit, but I would recommend the electric unit versus MV.

?     Asked on 7/2/2016 by Mark Gerry

How soon would this be shipped? What would be the estimated time of arrival to Minnesota? 55033 Thanks

A  Answered on 7/4/2016 by InyoPools Product Specialist Alex V.

Mark, Heaters are typically shipped within 24-48 hours after your order has been placed (not including weekends). Delivery usually takes 5-8 business days. Please note that this is a 266k btu, natural gas, millivolt heater.

?     Asked on 5/30/2016 by roger levy

can we reverse the water manifold to the opposite side. (from the right side to the left side) thank you Roger

A  Answered on 6/3/2016 by InyoPools Product Specialist Lennox H.

Hi Roger, The water connection can be reversed in the field. The reversal and installation has to be done by a pool professional or an authorized Raypak installer or else the warranty will be voided.

?     Asked on 4/25/2016 by Eric Lindstrom

I just purchased a Raypak Millivolt heater from you to replace my old Millivolt heater. I have a separate Jandy control system to turn on/off the heater for pool and spa modes. I don't see a wiring diagram for the Millivolt in the O&M manual as to how a Jandy system would be inter-connected. Can you point me in the right direction?

A  Answered on 4/27/2016 by InyoPools Product Specialist Lennox H.

Hi Eric, MV units can not be controlled or wired to an external controller

?     Asked on 6/2/2015 by Bob

my pilot light on my raypak 266000 will not stay lit. Any suggestions would be appreciated

A  Answered on 6/4/2015 by InyoPools Product Specialist Lennox H.

Bob, In The RayPak MV Owners Manual on page 43, there's a few things that can cause the issue you're having. They've also provided some solutions that you can try to see if that will fix your issue.

?     Asked on 5/13/2015 by John

Estimated delivery time on heater

A  Answered on 5/13/2015 by InyoPools Product Specialist Patrick P.

Estimated delivery on this heater would be 3-5 business days.

?     Asked on 8/23/2013 by Guest

Is there a conversion kit to convert this heater from natural gas to propane?

A  Answered on 8/23/2013 by InyoPools Product Specialist Patrick P.

Yes, there is a conversion kit to convert this heater from natural gas to propane. The part or model number for this kit is: 6234-70.

?     Asked on 5/11/2013 by Guest

Is the Raypak PR226AMN a cupro-nickel heater?

A  Answered on 5/11/2013 by InyoPools Product Specialist Patrick P.

The Raypak 009193 (PR266AMN) is not a cupro-nickel heater. The cupro-nickel is only available in the digital model which is a Raypak 010103 (PR2266AENX): http://www.inyopools.com/Products/04000013058201.htm

?     Asked on 10/10/2012 by Guest

What is the difference between an Electronic and Millivolt ignition?

A  Answered on 10/10/2012 by InyoPools Product Specialist Patrick P.

The basic answer is that Millivolt is the old style of ignition, using a standing pilot light. While the electronic ignition uses a spark start system like a gas grill. Electronic ignitions are more efficient in gas usage and also are better suited for high wind areas where a pilot light might get extinguished.

?     Asked on 1/16/2012 by Guest

Will a gas heater operate at the low speed of a dual speed motor?

A  Answered on 1/16/2012 by InyoPools Product Specialist Patrick P.

Probably not - Most gas heater will shut off at low GPM levels (20-40) to keep the heater cores from overheating - 20 for 200 BTUs, 40 for 400 BTUs. Depending on your pool system you might get these GPM levels at the low speed but generally these heaters must be run at the motor's high speed.


Est. Repair Time

2 to 4 hrs

Tools Needed

Screwdriver, Pliers, Adjustable Wrench

0     1

Pool heater finally died after 36 years of great service with only one repair several years ago.

Written on 9/18/2018 by Guest

Replaced the heater with the same brand and type. It was easy to remove the old and install the new. A plumber checked the connections and we are ready for the end of the season and the next season opener in 2019.
The hardest part was twisting the old black pipe off and then I had it replaced with new pipe to the new heater.

Were these instructions helpful? 


Review Summary

 (Average 4  out of 5 stars)
5 Rating
5 star:
4 star:
3 star:
2 star:
1 star:

The Most Helpful Review

The Most Recent Reviews