Part # FG1003PACK
Alternate Part #'s FC-9530, FS2003, PFS1836
Generic replacement DE filter grids offer an economical way to maintain your pool filter's optimal performance. Seeing DE powder in your pool is a typical sign of one or more torn grids which need to be replaced.
*Most DE filters require 7 full Grids and 1 partial grid. This is a pack which includes 7 full grids & 1 partial grid.
|Filter Area (Sq. Ft.).||Grid Length||Indentification||Full Grid Part #||Partial Grid Part #||Full Grid Width||Partial Grid Width|
|24||12"||American, Hayward, Pac-Fab, Pentair, Sta-Rite||FG1002||PG1902||11 - 1/2"||9 - 1/2"|
|36||18"||American, Hayward, Pac-Fab, Pentair, Sta-Rite||FG1003||PG1903||11 - 1/2"||9 - 1/2"|
|48||24"||American, Hayward, Pac-Fab, Pentair, Sta-Rite||FG1004||PG1904||11 - 1/2"||9 - 1/2"|
|60||30"||American, Hayward, Pac-Fab, Pentair, Sta-Rite||FG1005||PG1905||11 - 1/2"||9 - 1/2"|
|72||36"||American, Hayward, Pac-Fab, Pentair, Sta-Rite||FG1006||PG1906||11 - 1/2"||9 - 1/2"|
Note: Collar has open slot (2 notches). Length is measured from one end of the grid to the other (collar not included).
Hi need to replace grids of my Titan American De vertical Stainless steel filter, model 582090
also which O ring please for the same tank
I have to replace all DE filters on my Nautilus Model NS 36 Serial 048610 ,filter area 36 sq ft . Not sure which filter I should be getting for my system .
I am getting DE on the steps of the pool. My pool was built in 1983 or 1984. It has a stainless steel filter tank--model NS-36. I need to replace the 8 grid screens, as well as the plastic housing (due to some damage).
What is the right replacement parts for my pool ?
If this is the correct item then I would like to order tomorrow. Can you confirm:
(1) that these are the filter elements for the following pool filter:
Titan RPM Vertical Grid D.E Filter (marketed by Pentair)
Model No. 188585 (H-18-8550) RPM36
Series No. RPMF3731
Filter Surface P2 = 36
Filter Surface m2 = 3,34
Max Pressure 350kPa
(2) the dimensions of the package and weight?
(3) the postage to Ohio?
(4) postage times to Ohio
Hi Simon, The 36 Sq. Ft. Grid Pack (FG1003PACK) will fit the Titan RPM Vertical Grid D.E Filter 188585. Shipping dimensions are approximately 22"H x 17"W. Free ground shipping which can take 3-5 business days.
I have an old PAC-FAB Nautilus NS 36 de filter. I would like to replace all the grids. Is this the correct pack to order?
Hi Mike, Yes this DE Grid Pack is the correct kit for the PAC-FAB Nautilus NS 36 de filter.
Hello, I have an American Products RPM filter (36 sq feet) model n°188585
Is the FG1003PACK what I need to replace my elements?
Hi Jon, The FG1003PACK will fit the American Products RPM filter.
I have a Hayward DE3620 model and need to replace the filter grids. Which replacement set should I purchase? Thanks.
Hello- The FG1003Pack 36 Sq. Ft. Grid Pack (7 Full & 1 Partial) is the correct grid pack for the Hayward DE3620.
I have a Purex Triton Nautilus FNS 36 but it is not the Plus version. There are 7 grids 18 x 11.5 and 1 grid 18 x 9.5. Is part # FG1003 the correct grids? Tanks
I have a Hayward put in 2003 and need a new filter element cluster. How do I determine which size I need?
If you are lucky, the sticker on the front of the tank will have a mark next to your model number. Barring that, if you measure the length of one of the grids ( top to bottom ) and then multiply that number by 2, that is the square footage of your filter. Example : if your grids are 18" long, you have a 36 sq ft DE Filter.
Hello i would-like to know if this is the right grids for my filter pentair fns 36.
Thank you .
Hello Pascal, yes if you have the FNS plus or Nautilus these units will be the replacement grids.
My filter parts is: FLT FNS PLS48. Now I need to replace two complete sets of Pentair filters. Which model should I buy? Could it be: Filter Area (sq. ft.): 48 Grid, Length: 24", Identification: American, Hayward, Pac-Fab, Pentair, Sta-Rite, Full Grid Parts #: FG1004, Partial Grid Parts #: PG1904, Full Grid width: 11 - 1/2", Partial Grid Width: 9 - 1/2" ?
My own measurement of the existing Full Grid width is 10 - 1/2". So it doesn't quite tally. Any advice?
Hi Mohd, The 48 Sq. Ft. Grid Pack (7 Full & 1 Partial) (FG1004PACK) would be the correct size grid pack needed for your model filter.
I have a purex triton fns plus DE filter, model #fnsp 36, 2009 E, and need a replacement grid pack. Will this model fit? Thanks
Hi Joe, The 36 Sq. Ft. Grid Pack (7 Full & 1 Partial) (FG1003PACK) will be the correct replacement size grid pack.
I have a Model E-LE-42052 manufactured by Hayward but sold through LESLIES pool supply as a Crystal Clear II DE filter. Will the 36ft/2 work with this model?
Hi B.H, The 36 Sq. Ft. Grid Pack (7 Full & 1 Partial) will work with your current Crystal Clear II 36 sqft DE filter.
Less than 1 hr
Less than 1 hr
Socket Set, Wrench Set
This was done while the pool was closed so the prerequisite steps of relieving pressure, draining and opening the filter were already done, and the filter assembly was already removed.
1. Using a wrench or pliers to hold the bolt at the bottom, loosen the threaded rod that runs through the filter assembly. No need to completely remove the rod.
2. Carefully pop the top plate off the individual filters - in my case, a couple were stubborn, but with some gentle persuasion, they came loose.
3. Pay close attention to where the short filter fits. It isn't that complicated if you look at where it fits in relation to the gap on the bottom plate. Also note how the screens fit in between the spacers/holders in the bottom plate.
4. I found it easiest to remove all the screens, wash off the top and bottom plates, and then re-assemble. Again, make sure the short screen is in the correct position.
5. Reposition the top plate - it can take a little bit of fiddling to get all the screens aligned with the holes in the top plate, but take your time and you'll get it.
6. Again, with a wrench on the bottom of the threaded rod, tighten from the top.
7. Confirm that there is a space for the outflow tube from the gap in the bottom plate up to the connection in the top plate. If not, you installed the short screen in the wrong place.
8. In the filter body, make sure the o-ring where the filter assembly meets the outflow tube is in good shape and is well lubricated.
9. Press the filter assembly on to the outflow tube
10. Re-assemble and recharge your filter per the instructions.
4 to 8 hrs
After changing the DE and still no improvement, I decided the filter was not working. So I pulled the top half off the filter and found that 5 of the grids were broken off where they connect to the outlet header of the filter. This allowed the water and the new DE I added to pass right through the filter and back into the pool. I went to INYOpools on internet and ordered a new set of grids for my filter and associated o-ring. I installed the new grids and new DE and within 2 days the water was clear as it should be.
(5 out of 5 stars) Crystal Clear Pool Water
Reviewed By: Jayne B. from Farmingdale, NY ()
Pros: Price, in stock, quick turn around
After trying everything we could think of to get out pool sparkling again, we knew we needed to replace the grids in our filter. We shopped around and found that Inyopools offered us the best price, less than half of what our pool supply store wanted!! We received the grid pack and installed it in less than 15 minutes, we are happily in the swim again! Thank you Inyopools.
(5 out of 5 stars) Great Replacement Filter Cartridges
Reviewed By: Jeffrey S. from Toms River, NJ ()
Pros: Great product and quality
Very easy to order and the product is as good or better than the original. Found inyo pools pricing way below what I was quoted for a replacement at a pool supply.