Impeller, SP1500L, Hayward - SPX1500L

$42.99

IN STOCK
FREE SHIPPING

Part # 5111-07F

By Hayward Pool Products

  5 Average  

Details

Top

Part # 5111-07F

Manufacturer Code SPX1500L

Dimensions 3.8" X 0.6"

Alternate Part #'s 351501160, SP1500L, SPX1500-L, SPX1500L

Product Description

OEM impeller rated for 1, 1.5 and 2 HP.  Used on the Hayward Matrix, Power-Flo 1500 Series, and Power-Flo LX.

Top

?     Asked on 9/6/2018 by Mike

The impellar broke off on my Hayward power flo matrix so 1593 and has plastic so 1500l impellar. Also damaged the spring assembly behind trying to get it out. What parts do I need to fix everything while I have it disassembled? Thanks, Mike
 Reply

A  Answered on 9/7/2018 by InyoPools Product Specialist Lennox H.

Hi, Mike. I would recommend that you replace this Impeller - SPX1500L along with the Matrix Pump  Tune Up Kit - GOKIT74
 Reply


?     Asked on 8/10/2017 by mike

I have a Power-LX 1 HP pump model # SP1580Z2 . Could you please tell me the proper part numbers for a new impeller and shaft seal. Thank you
 Reply

A  Answered on 8/10/2017 by InyoPools Product Specialist Alex V.

Mike, If your pump is the SP1580, then the SP1500L would be the correct impeller. Hayward has a few different versions of the PowerFlo pump. I would recommend taking a look at your impeller. There is a part number molded into the front of it. Also, please be sure to change the shaft seal wehn you replace the impeller. 
 Reply


?     Asked on 6/1/2017 by

I have a SP 1510-Z-1-XBC. Which one of these impellers and bearing/seal kits will fit this model.
 Reply

A  Answered on 6/3/2017 by InyoPools Product Specialist Lennox H.

Hi. You can use this SP1500L, with the SP1510-Z-1-XBC motor. In order to locate the proper seal kit, I will need to know the model of the pump housing.
 Reply


?     Asked on 5/28/2017 by Thomas Wieczorek

I have a model SP1580 1 HP Hayward pump. It produces only 14 to 20 Lbs. PSI. when I run it without the filter it pulsates rather than a steady stream. I suspect the impeller or a seal is not operating correctly. What is your opinion? the whole assembly is only 3 years old. I want to order the correct parts before I disassemble it Thank you for your anticipated response...
 Reply

A  Answered on 6/8/2017 by InyoPools Product Specialist Lennox H.

Hi, Thomas. What you're experiencing can be caused by several things including a clogged impeller as far as the intermittent water flow. The high pressure could be caused by a dirty or old cartridge. Intermittent water flow and high pressure can be caused by a clogged impeller if the strainer basket is broken or a suction leak causing air to get into the line.
 Reply


?     Asked on 2/22/2017 by

will this fit a 1 hp power flo 2 1510L
 Reply

A  Answered on 2/22/2017 by InyoPools Product Specialist Scott W.

Yes, that is the correct replacement impeller for your Power-Flo.
 Reply


?     Asked on 9/24/2016 by Moira

What are the seal numbers for the part that goes over the shaft. Thanks
 Reply

A  Answered on 9/26/2016 by InyoPools Product Specialist Alan M.

Hello Moira, The correct shaft seal you would need is the Seal Assembly (psr 2131). This will fit the Hayward Matrix and Powerflo pumps.
 Reply


?     Asked on 8/13/2016 by Brenton

I have a hayward power flo lx pump sp1515z1bc 1.5 hp and I need to put a smaller impeller on to reduce power. Which one should I use?
 Reply

A  Answered on 8/21/2016 by InyoPools Product Specialist Lennox H.

Hi Brenton, This Impeller SP1500L is also used with some 1.5 hp models, so may need the Impeller (SPX1500F). To confirm you ll need to chek the p/n on your pump impeller.
 Reply


?     Asked on 6/12/2016 by Hank

Why does my 1520 pump loose pressure when I try and use the vacuum ?
 Reply

A  Answered on 6/12/2016 by InyoPools Product Specialist Matt S.

There may be an air leak in the vacuum hose. For a checklist on what may be causing your problem, read this how-to guide: How to Correct Low Water Pressure in Your Pool System
 Reply


?     Asked on 9/13/2015 by Tommy Kiser

My impeller has a seal assembly broken off of it. When I order a new impeller do I also need to order a seal assembly #5111-03, or is this seal assembly built into the new impeller.
 Reply

A  Answered on 9/17/2015 by InyoPools Product Specialist Lennox H.

Hi Tommy, The Shaft Seal Assembly (PSR 2131) is not built into the Impeller. I would recommend replacing the shaft seal along with the impeller.
 Reply


?     Asked on 9/13/2015 by Tommy Kiser

My impeller has a molded spring in back where it screws on.
 Reply

A  Answered on 9/15/2015 by InyoPools Product Specialist Robert M.

Hello Tommy - The spring part on the back of the impeller is part of the shaft seal. That piece can be removed from the impeller.
 Reply


?     Asked on 9/3/2015 by

Does SPX 1500 KA seal assembly with cup work with this impeller? Does this impeller have a brass fitting with threads? The original had plastic.
 Reply

A  Answered on 9/9/2015 by InyoPools Product Specialist Lennox H.

Hi, The Hayward Shaft Seal (SP1500KA) can work with Hayward Impeller (SP1500L). The Hayward Impeller (SP1500L) does have a brass threads fitting.
 Reply


?     Asked on 6/30/2015 by

Will this fit and work with hayward SP1540CLSNP?..look like the old impeller i just took off
 Reply

A  Answered on 7/2/2015 by InyoPools Product Specialist Lennox H.

Hi, The Hayward SP1500L Impeller will work for the SP1540 Pump
 Reply


?     Asked on 6/20/2015 by

Is this the correct impeller for model#SP15921TLFP?
 Reply

A  Answered on 6/21/2015 by InyoPools Product Specialist Matt S.

Hello Rich, yes this 1 HP impeller with fit the Hayward Matrix SP1592 1 HP
 Reply


?     Asked on 12/7/2014 by Len

I have a power flo lx pump (SP1510) with a SP1500L impeller. This part looks to be the correct part, but the threaded part on mine is plastic and the one in the picture looks to be brass. Is it this the correct replacement part? Did they change the material of the threaded part?
 Reply

A  Answered on 12/8/2014 by InyoPools Product Specialist Brian M.

That is the correct part  replace your existing one. They now make the shaft out of brass to avoid the plastic from cracking.
 Reply


Top

Review Summary

 (Average 5  out of 5 stars)
12 Rating
5 star:
 
(12)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews