Part # 5056-08
Manufacturer Code U109-93SS
Dimensions 1.3" L x 1.23" W x 1.23" D
Alternate Part #'s 004547, 351021030, 39960149, STA605141, U10993SS
SEAL, SHAFT (U109-93SS-50) - used on older style pumps that have a seal insert (pre-1998 for the Dura-Glas).
on a usq1102 pump motor is there a different seal for salt water systems
Hi. The PS-3866 is the Saltwater pump seal that can be used as a substitute for this U109-93SS-50 shaft seal.
is this 5\8 or the 3\4 i.d size seal
Hi, Pete. This seal has a 5/8" ID.
need a motor seal for this pump modle: MPRA6D-146L The Motor Model is: C48J2PA105C1 Ser: 1CW 3/4hp Fr 48Y 115/230v 3450 rpm A. O. Smith Corp Alt # 01 U27-1221
I have anthony pools AR207-L model impeller housing with 2 hp Centurion motor, 7-186016-20. Is this correct seal?
Hi Mike, Yes this is the correct seal for the Anthony Pools AR207-L model pump.
that sure looks the seal i am looking for do they come in deferrent sizes
Yes they do come in different sizes. Could you email us the make and model of your pump?
Is there any physical difference between the Pentair Shaft Seal U109-93SS (Part #5056-08) and the Generic Shaft Seal PSR100 (Part #5250-100)? Do both seals use the same type/quality of materials (stainless steel, ceramic, plastic and rubber)? I don't care that one is made by Pentair and the other by US Seal, I'm more concerned with the quality of materials. I've had some problems with rusted seals and want to make sure either seal will function the same.
Yes sir, either seal will hold up the same. I don't know which Pentair pump you're referring to otherwise I would give you specifics, but if there's a saltwater shaft seal on the parts diagram for that pump I'd recommend purchasing that one if you're worried about rust.
I have a AO Smith pump (p/n: 7-165201-07) 2HP serial No. 317063M. The shaft seal is leaking...what parts do I need to fix it? thanks
We would need the front pump housing model that the motor bolts to in order to cross reference that seal for you.
do i need to use silicon to glue in the ceramic seal into a pre 1998 sta rite dura glas? where the silicon needs to be - between seal side and?
No you would not need silicone glue to install this shaft seal. We have a guide with Video on How to Install a Shaft Seal which will walk you through the installation process.
The mechanical seal has two white side surface, one larger then other. What side is face-up on the seal plate? Also what end of the Shaft seal meet the seal plate and the Impeller. This is my first time changing the pool motor. Thank you.
Hi Rich, You would place white side of the shaft seal up inside of the seal plate. We have a great Video on How to Replace a Pool Pump Shaft Seal which goes into great detail on the topic.
(4 out of 5 stars)
Reviewed By: Kevin from Roseville, CA ()
Pros: Good price
Cons: Bought one locally. Didn't fit
The rubber boot that the cermic stationary seal seats in was wrong diameter. I found out after I bought a new seal locally that I could reuse the old boot with the new cermic seal. I saved everything and will use it next time I replace the seal.
(5 out of 5 stars) Perfect replacement shaft seal.
Reviewed By: William P. from Springfield, VA ()
Pros: perfect fit
Perfect fit pump motor shaft seal. Easily installed and furnished in box with written instructions. Not clear was which side of the two pieces mate to each other. Instructions only caution to pay attention when disassembling the old seal. My pump, however, had been disassembled by another individual. Using the tutorials and parts diagrams on INYOpools site provided the needed clarification. I wore uncoated, latex gloves to keep from leaving skin oil on the ceramic seal surface.