$262.99
By AquaStar Pool Products
Part # 3816-013
Manufacturer Code LPRFS9103
Alternate Part #'s LPRFS9103, 55-300-1201
Availability This Main Drain Has Been Recalled and is No Longer Available
************************************************
GENERAL DESCRIPTION: 9"X 9" SQUARE RETROFIT MAIN DRAIN COVER, LOW PROFILE, LIGHT GRAY************************************************
BASIC SPECS: THIS IS THE EXTRA LOW PROFILE AQUASTAR 9" X 9" REPLACEMENT COVER SCREW HOLES: 1 IN THE CENTER OF EACH SIDE 2 OF THE SIDES HAVE 3 HOLES WITH 1 IN THE CENTER SEE BELOW FOR DETAILS USAGE: APPROVED FOR FLOOR OR WALL USAGE SPECS: SPECS SHOWN ARE FOR A SINGLE UNIT FLOOR: 100 GPM @ 4.2 FPS WALL: 70 GPM @ 2.9 FPS LIFE: 5 YEARS TOTAL OPENING: 7.7 SQ INCH 36 GPM @ 1.5 FPS************************************************
DETAILED DESCRIPTION: THIS IS A 9" X 9" SQUARE REPLACEMENT COVER THIS IS AN ANTI-ENTRAPMENT RETROFIT COVER AND SCREWS THIS IS VERY LOW PROFILE COVER (1/8" HEIGHT ABOVE PLASTER LINE) THIS HAS SCREW HOLES DESIGNED TO LET IT REPLACE A WATERWAY, HAYWARD OR PENTAIR 9" X 9" SQUARE COVER THIS IS A MODEL LP8AV 8" ROUND COVER ATTACHED TO A SQUARE ADAPTOR PLATE EACH SIDE HAS A SQUARE NOTCH AT THE BOTTOM MATERIAL: PLASTIC COVER, STAINLESS STEEL SCREWS COLOR: LIGHT GRAY SHAPE: SQUARE************************************************
COVER DIMENSIONS: COVER LENGTH & WIDTH: 8-25/32" (A) HEIGHT: 1-1/16" (AT THE OUTSIDE EDGE) MAXIMUM HEIGHT: 1-3/16" (AT THE CENTER OF THE COVER) (B) MAXIMUM HEIGHT ABOVE PLASTER LINE: 1/8" FOR A 1-1/16" DEEP FRAME THIS WILL DEPEND ON THE DEPTH OF THE FRAME (THE SIDE OF THE COVER IS FLUSH WITH A 1-1/16" DEEP FRAME AT THE EDGE) THE CENTER OF THE COVER IS 1/8" TALLER THAN THE EDGE************************************************
SCREW HOLES: THE COVER HAS SCREWS PLACED SO THE COVER WILL MATCH THE OLDER STANDARD WATERWAY, AND THE PENTAIR AND HAYWARD OLDER AND CURRENT FRAMES THERE IS ALSO AN 11/16" DEEP NOTCH, 5/8" WIDE IN THE CENTER OF EACH SIDE THE CENTERLINE OF EACH SCREW HOLE IS ABOUT 5/16" FROM THE OUTSIDE EDGE OF THE COVER FROM THE CENTERLINE OF EACH SCREW HOLE TO THE CENTERLINE OF THE SCREW HOLE ON THE OPPOSITE SIDE IS 8-3/16". SCREW HOLE PLACEMENT: TOTAL SCREW HOLES - 8 THERE IS ONE SCREW HOLE IN THE CENTER OF EACH SIDE 2 OF THE SIDES HAVE AN ADDITIONAL 2 SCREWS EACH OF THESE IS 2-7/8" FROM THE CENTER HOLE MEASURED CENTER TO CENTER************************************************
SCREWS: THERE ARE COMPLETE SETS OF 2 DIFFERENT TYPES OF SCREWS THERE ARE ALSO 2 ADDITIONAL OF THE #10 X 3/4" SELF TAPPING USED TO HOLD THE ROUND COVER TO THE ADAPTOR (4) #10 X 3/4" LONG SELF TAPPING (4) #10-24 X 1-1/4" LONG MACHINE THREAD************************************************
MARKINGS: MODEL # LP8AV - XXX IS MOLDED INTO THE CIRCULAR CENTER COVER P/N RFS9 101 THRU 108 IS MOLDED INTO THE BOTTOM OF THE SQUARE ADAPTOR THE SPECS REQUIRED BY THE VGB-2008 LAW ARE ALSO MOLDED ON THE COVER
