Pure Colors LED Pool Light Fixture 12V 30' Cord & Remote Control - PL5823


Part # PL5823

By PureLine



Part # PL5823

Warranty 2 Year Warranty

Product Description


Pure Colors LED pool & spa light fixture's offer seven solid colors, and nine light shows that can instantly transform your pool area into a color-rich paradise. The Pure Colors bulb uses an Edison screw in base, so the LED bulb is easily replaced if it every burns out. Plus, LED technology makes them the most energy efficient and longest lasting light on the market.


  • LED technology
  • RF Hand Held Remote Included
  • Operation through Hand Held Remote and/or Light Switch
  • 80% Operational Cost Savings
  • Standard screw in light base for quick & easy replacement
  • Synchronize multiple lights to operate in unison
  • 50,000 hours Lifespan
  • 2-year warranty
  • 441- LED's


  • Hayward Astrolite SP058 Series
  • Pentair Amerlite 784 Series
  • Note: Not compatible with Swimquip Light Fixtures or Hayward SP0540 series.


Will the PureColors Pool LED Bulb with RF Remote synchronize with the standard PureColors Light Switch Control Bulb? The PureColors RF Remote Control Bulb will not synchronize with the with the PureColors Light Switch Control LED Bulb as the inner control board of the two bulbs are different as well as the color show programs.

Will two RF Remote Bulbs Synchronize with each other? If you have two RF Remote bulbs they may not always synchronize. Because the lamps are installed underwater and the water will block the signal in various degrees, also since the bulbs are at different distances this can affect synchronizing. The remote will turn both lights on and off and set set the lights to a fixed color without a problem but the color shows may fall out of synchronization. Most likely your lights will also be hooked up to a light switch and if the lights are wired to the same switch then cycling through the color show with your light switch instead of the remote will ensure that the bulbs synchronize together in color changing mode.

If I have two PureColors LED Bulbs with RF Remote control, will one remote work on both bulbs? Yes one remote can be used for both bulbs. Remember you must have two RF remote bulbs as the RF remote will not turn on Non RF remote bulbs.

What do the 4 buttons on the remote control do? Button #1 is for cycling through the 7 fixed colors of the bulb. Button #2 is for cycling through the 5 color shows of the bulb. Button #3 is for adjusting the changing speed when the bulb is in color changing mode. Button #4 is to turn the bulb on & off.

Can you change the functions of the 4 buttons on the remote? No the functions on the remote control cannot be changed and they are pre-set.

Do these bulbs have memory? When turning the bulbs on and off with the RF remote control then the bulbs do not have memory, meaning that if you had your bulb set on blue and if you turn your bulb off for more than 15 seconds then the next time you turn the bulb on with the remote then the bulb will not turn back on in the color of blue. The bulbs do have memory when you turn them on and off using your light switch meaning that if you have your bulb set to green and you turn the bulb off using your light switch then the next time you turn your bulb on using the light switch then the bulb will be in the green mode.

Product Specifications

Bulb Type:
Cord Length:
30 ft.
Face Ring:
White Plastic
Pool / Spa Type:
12 V
Remote Control
35 W
White: 2,600 Colors: 850
Incandescent Equivalent:
300 Watts

?     Asked on 7/5/2017 by dan

Where is the 2nd part of the remote ? Part of the fixture underwater?Or in line with the transformer. Thanks Dan

A  Answered on 7/7/2017 by InyoPools Product Specialist Lennox H.

Hi, Dan. The Remote Receiver is located inside of the bulb. The Intermatic Transformer is sold separately. 

?     Asked on 5/23/2017 by

would i have to supply a 12v power supply fdor unit? i now have a 110v light fixture and would like to replace it

A  Answered on 5/23/2017 by InyoPools Product Specialist Patrick P.

Yes you would require this 100 Watt Transformer if you didn't want to install a transformer then you could go with one of the 120V PureColors Light Fixtures here.

?     Asked on 5/2/2017 by Tom

Would I have to lower the water level below the light to replace my existing pool light?

A  Answered on 5/2/2017 by InyoPools Product Specialist Patrick P.

No you would not need to lower your water level, here is our Video on How to Replace a Pool Light which will show you the process.

?     Asked on 4/16/2017 by Jacob McKinney

How many amps is the bulb?

A  Answered on 4/17/2017 by InyoPools Product Specialist Patrick P.

This bulb draws 3 amps

?     Asked on 4/5/2017 by Bill

What are the dimensions/size of this light? I haven't pulled my light out yet and wanted to know if this light will button up to the Stainless Steel ring I have mounted to my pool wall. It is 10 1/2 inches wide.

A  Answered on 4/6/2017 by InyoPools Product Specialist Patrick P.

Hi Bill, The face of this light measures 10-3/4" this is the measurement including the face ring. The depth from the front of the glass lens to the back of the light where the cord comes out is 8". The narrow part of the light where the cord comes out of the light measures 2-3/4"

?     Asked on 4/2/2017 by Lisa

Hello. I need to replace 3 lights in my pool. I have halogen ones now and I would like to go to LED. My existing lights work off of a light switch. Could I sync the three lights if I use the switch instead of remotes?

A  Answered on 4/4/2017 by InyoPools Product Specialist Patrick P.

Hi Lisa, Yes you can synch 3 lights together and I would suggest using a light switch instead of the remotes as we have better success with synching multiple light when you using the light switch over the remote. I would suggest this PureColors LED Light 12V 30' Cord Light Switch Model