1 HP Pool Motor Square Flange 48Y (Pre-Order Shipping June 1st, 2019) - PL2102

$124.99

IN STOCK
FREE SHIPPING

Part # PL2102

By PureLine

  3 Average  

Details

Top

Part # PL2102

Warranty 1 Year

Alternate Part #'s 13557, 186359, 187332, 3K032, 54003, 5KC36NN6017X, 5KC38SN6084X, 5KC39PN2073, 5KC39PN2073X, A100EL, A100ELL, B692, B853, B853SE, B853SM, B886, C1245, C48B19B84, C48K2EB102, C48K2EB104, C48K2EM15, C48K2P104, C48K2PA104, C48K2PA104A1, C48K2PA104A3, C48K2PA105, C48K2PA105A1, C48K2PA105A2, C48K2PA105A7, C48K2PA105C5, EB853, SQ1072, SQD10UP1, USQ1102, V54003

Availability PRE-ORDER SHIPPING JUNE 1ST, 2019

Product Description



PureLine 1 HP Replacement Pool Motor for Pentair & Sta-Rite Pumps

Is your pool pump motor running loud, leaking or humming? These are all signs that it’s time to be replaced. The PL2102 PureLine Replacement motor is designed as a drop-in replacement motor for some of the most popular 1 HP pool pumps like the Sta-Rite Max-E-Glas, Max-E-Glas II, Dura-Glas, Dura-Glas II, Dyna-Glas, Dyna-Max, Pentair Whisperflow and Pentair Pinnacle and many more.

The PureLine replacement motor is made of the highest quality components like sealed ball bearings which means it is an ultra quiet motor. Because of its high-quality construction the PureLine replacement motor is backed by a full 1-year warranty.

When it comes to replacing your motor Inyo has you covered we have created a ton of resources to make this project a snap, like our Video on How to Replace a Pool Motor this video walks you through all the steps to replace your motor. Most of our customers decide to tackle this project on their own and by following our video they complete this project in about an hour.

When replacing your motor we highly recommend a tune up kit which includes all the seals and gaskets for your pump. Many times when you use your old seals you may have leaking and seal leakage is one item which will void the motors warranty so make sure to protect your investment with a tune up kit. Below we have listed the tune up kits for some of the most popular pool pumps.

Don't Forget Your Tune Up Kit

See all of our Pool Pump Tune Up Kits

Product Specifications

Motor Name:
1 HP Pool Motor Square Flange 48Y
HP:
1 HP
Speed:
Single
RPM:
3450 RPM
Volts:
115/230 V
Amps:
15/7.5 amp
Service Factor:
1.0
Frame:
48Y
Shaft:
Threaded
Commonly Used On:
Sta-Rite Max-E-Glas, Max-E-Glas II, Dura-Glas, Dura-Glas II
Flange:
Square
Top

?     Asked on 4/21/2019 by

Hi I need replacement for Pool Motor, 1-1/2 HP, 3450 RPM, 115/230V CENTURY |Mfr #:B2854
 Reply

A  Answered on 4/21/2019 by InyoPools Product Specialist Patrick P.

We would suggest the PL2854 Motor as a suitable replacement for your motor.
 Reply


?     Asked on 3/24/2019 by

We are replacing our pool motor. It is a UST1102 with model #C48K2N143C1C. It is for an inground pool but I am only finding USQ1102. What is the difference between the UST1102 and the USQ1102?
 Reply

A  Answered on 3/24/2019 by InyoPools Product Specialist Lennox H.

Hi. The motor mounting frame is the differences. The UST1102 has a 56J frame and the USQ1102 has a 48Y frame. You can use the UST1102, or the PL1102 motor as a replacement. 
 Reply


?     Asked on 5/4/2017 by

replacing sta-rite P2R A5E-181 L, Online chat suggested the PL2102, what is the correct tune up kit?
 Reply

A  Answered on 5/4/2017 by InyoPools Product Specialist Patrick P.

Hi, Based on your part # you have a Sta-Rite Dura-Glas and the PL2102 is the correct replacement motor. If your pump is Pre 1998 then you need this Pre1998 Sta-Rite Dura-Glas Tune Up Kit and if your pump is 1998 to Present then you will need the Sta-Rite Dura-Glas 1998 to Present Tune Up Kit. If you don't how old your pump is, then we have put together a Video on How to Tell If I have a Pre 1998 Sta-Rite Dura-Glas or Post 1998 Dura-Glas, which you should find helpful.
 Reply


?     Asked on 5/1/2017 by

is the motor shaft the same size as the one i have.
 Reply

A  Answered on 5/1/2017 by InyoPools Product Specialist Lennox H.

Hi. The shaft size of this motor is built with the same specs as the Century pool motors ensuring that it fits.
 Reply


?     Asked on 4/26/2017 by

Old Original Motor was Hayward Super Pump SP1607-z01m Need replacement
 Reply

A  Answered on 4/26/2017 by InyoPools Product Specialist Scott W.

A good replacement motor would be the PL1102 along with the seal kit, part number GOKIT1.
 Reply


?     Asked on 4/20/2017 by Randy

I have a Sta-Rite P4EA6E-150L that needs the pump motor replaced. Currently it has an A.O. Smith motor with mostly unreadable label except 1102 & 48Y. Will this PL motor work or would another A.O. Smith be the better replacement?
 Reply

A  Answered on 4/22/2017 by InyoPools Product Specialist Patrick P.

Hi Randy the PL2102 would be a great replacement motor for your Sta-Rite P4EA6E-150L Pump. We would also suggest a Max E Glass II Tune Up Kit When Replacing your motor.
 Reply


?     Asked on 4/8/2017 by brannon malcom

need to replace an a.o.smith model C48L2PA103A2 WHAT ARE MY CHOICES
 Reply

A  Answered on 4/9/2017 by InyoPools Product Specialist Patrick P.

Hi, for your C48L2PA103A2 you would require the PL2152 1.5 HP Replacement motor Your current motor is a 1 HP full rated motor which is equivalent to the 1.5 HP uprated motor that we have suggested.
 Reply


?     Asked on 4/5/2017 by Richard Lukso

Is the shaft length 2.3"?
 Reply

A  Answered on 4/6/2017 by InyoPools Product Specialist Alex V.

Richard, Unfortunately, I do not have a measurement on the shaft length. What motor are you trying to replace?
 Reply


?     Asked on 1/28/2017 by Bill Hochner

Can this motor be used as a replacement for my A.O. Smith Model K48L2N104 1 HP 115/230VAC, 3450 rpm
 Reply

A  Answered on 1/30/2017 by InyoPools Product Specialist Scott W.

The direct replacement for your current motor is CT1102. Along motor you could go with is the ST1102.
 Reply


?     Asked on 1/16/2017 by Bud

I have a Dura Glas pump model P2RA5E-124 which needs a new motor. Is your number PL 2102 the correct replacement? I also want to rebuild the pump using kit number GOKIT6 and because it was made before 1998 the copper seal number 5056-07A. Are these the correct parts and do you have any suggestions.
 Reply

A  Answered on 1/16/2017 by InyoPools Product Specialist Scott W.

Yes, both of those will be what you need to get your Dura-Glas back up and running.
 Reply


?     Asked on 1/16/2017 by JB

i need to replace my p6e6e motor can i use the pl2102 motor to replace it
 Reply

A  Answered on 1/16/2017 by InyoPools Product Specialist Lennox H.

Hi, JB. Unfortunately, in order to use the PL2102 motor, you will have to downsize the impeller which will also reduce water flow. The PL2102 motor has a lower total horsepower than what it's originally designed for. You can use the QC1102 EE Motor which is the direct replacement or the SQ1102 standard motor.
 Reply


?     Asked on 1/15/2017 by Bob Schwyn

I need a replacement motor on my pool pump. It is a Sta-rite Dura-glas pump. The motor is model #C48K2PA105. 1 HP. Please recommend the correct replacement motor.
 Reply

A  Answered on 1/16/2017 by InyoPools Product Specialist Patrick P.

Hi Bob, The PL2102 motor on this page is the correct replacement motor for your Sta-rite Dura-glas pump with a C48K2PA105 motor. When replacing your motor we strongly recommend a tune-up kit, the kit includes a shaft seal as well as all the gaskets for your pump. The tune-up kit ensures that you don't have any leaking when you install the new motor. There are a few different tune-up kits for the Sta-Rite Dura-Glas so we put together this Video on How to Select a Sta-Rite Dura-Glas Tune Up Kit Here is the Tune Up Kit for pre 1998 Dura-Glas and here is the Tune Up Kit for the after 1998 Dura-Glas. Finally here is a Video on How to Replace a Pool Pump Motor which you may find helpful.
 Reply


?     Asked on 1/7/2017 by daniel robinson

I have a Dura-glas II 1hp 208v with a motor# ae100eh2 what motorr places it?
 Reply

A  Answered on 1/9/2017 by InyoPools Product Specialist Alan M.

Hello Daniel- Here is a link to the Sta-Rite Dura-Glas II and Max-E-Glas II Parts page for your reference. There are two available replacement motors. One is made by Pureline, the 1 HP Pool Motor Square Flange 48Y - PL2102 and the other is made by A.O. Smith/Century, the A.O. Smith 1 HP Square Flange Full Rate Motor - SQ1102. We would also recommend you replace the seals whenever you change out the motor. You will need the Tune Up Kit Starite P4E & P4EA Max-E-Glas II / DuraGlas II - GOKIT38.
 Reply


?     Asked on 12/31/2016 by Ron Kocher

I need to replace the motor in a Sta-rite P2RA5E-181L. Motor model # is C48K2PA105. It looks like your Pureline PL2102 motor will work. Do u agree? Just want to be sure before I order it. Thanks!
 Reply

A  Answered on 1/2/2017 by InyoPools Product Specialist Patrick P.

Hi Ron, Yes the PureLine PL2102 would be the correct replacement motor for your C48K2PA105
 Reply


?     Asked on 12/28/2016 by Alex

Purchased a PL2102 to replace an AO Smith motor. Old motor had blue wire connected to L1 and black wire connected to L2 on a 230V set up. On PL2102, do I connect the black wire to terminal 1 and the blue wire to terminal 3 or vice versa? Diagram received with the PL2102 shows the power line going to terminal 3, but not sure if this is the blue or black wire. Thank you for the assistance.
 Reply

A  Answered on 12/28/2016 by InyoPools Product Specialist Adam Y.

Good morning Alex, On the motor label there is a wiring diagram and it shows you the terminals where you should be  for 230v.
 Reply


?     Asked on 12/14/2016 by Louis

Hi, I have a pool motor Century A.O. Smith serial # BZ0928 part #717745103 type CX ,HZ 60, Volt 230 amp 96 , will it match as a replacement for the 13yr old one that's is rather irritating. I have a pool spa.Jacuzzi ? Interested in your offer .
 Reply

A  Answered on 12/15/2016 by InyoPools Product Specialist Alan M.

Hello Louis - The direct replacement motor for the model you listed, #717745103, is the 1.5 HP Motor EE Full Rate (B2842).
 Reply


?     Asked on 11/13/2016 by Elaine Levenseller

We have an older pump P2RA5E-181L, 1HP, Type B, . We had our in ground pool changed over to a salt water pool last summer and we knew the pump was getting old. It now just hums and wont pump and water. We would like to replace the pump thinking it would be more economical. Is there a 2 phase pump that we can replace it with or do we have to stay with the 1 phase. Thank-you, Elaine
 Reply

A  Answered on 11/14/2016 by InyoPools Product Specialist Stacey M.

Hello Elaine, if you are looking for a whole pump replacement and want to stay with a Starite brand these are all units for Starite. If you are looking for something more economical may I suggest a Variable Speed, please make sure you have 2" plumbing and are hooked up for correct voltage.
 Reply


?     Asked on 11/6/2016 by Gustavo

My motor serial # is 5kc39pn2822bx. This motor you have, it works for me?
 Reply

A  Answered on 11/7/2016 by InyoPools Product Specialist Adam Y.

Good Morning, The motor Im pulling up based on that serial number is  a Marathon Electric 1 H.P. Round Flange Motor - C1318 which is no longer available. The closet available match is a A.O. Smith 1 HP Round Flange Up Rate Motor - UST1102 which will work.
 Reply


?     Asked on 11/6/2016 by Steve

I currently have a DuraGlas P2RA5E-181L and it is tripping the breaker after it heats up. This can last 30 min - 1 hour. I'm thinking about just replacing the motor and cleaning up the rest. Is there any other seals that I need to buy?
 Reply

A  Answered on 11/7/2016 by InyoPools Product Specialist Stacey M.

Hello Steve, depending on whether you have pre1998 for gokit6 and then there is gokit54 for 1998 to present. If you are not sure you can just get the gokit54 you would just remove the copper cone in the pump. There is a "how to" video on this here.
 Reply


?     Asked on 11/5/2016 by George

Hi. I have a pre-1998 Hot Springs spa with a STA-RITE Max-E Glas pump. The motor is Model K48K2PA105 Series 8191; 1HP, 3450RPM, 115/230 Volt, KW.75 It is in need of replacement. Is this the right replacement motor? Also would it be worth while to replace the Seal Plate with the newer kit? I had replaced all the o-ring seals previously, but it still leaked like a sieve (even after rechecking tightness and seating.) Thanks.
 Reply

A  Answered on 11/7/2016 by InyoPools Product Specialist Lennox H.

Hi George, This PL2102 motor can be used to replace the K48K2PA105 motor but it will use more energy since the K48K2PA105 is an energy efficient motor. Yes, I would also recommend replacing the Seal Plate Kit (C203-193P) to ensure that pump does not leak.
 Reply


?     Asked on 10/27/2016 by Wayne

Will this motor replace a Hayward 1 HP for a 20 x 40 inground pool?
 Reply

A  Answered on 10/27/2016 by InyoPools Product Specialist Adam Y.

Wayne, Do you have a model number of the existing pump or motor I need to no if its a round or square flange and if your current motor is full rated or up rated.
 Reply


?     Asked on 10/26/2016 by Jim

My current pump motor is a DuraGlas P2RA5E-181L. Is this pump a compatible replacement?
 Reply

A  Answered on 10/27/2016 by InyoPools Product Specialist Scott W.

Yes, that is going to be one of the replacement motors for your DuraGlas. If you have the motor part number I can confirm that is the motor that you are needing.
 Reply


?     Asked on 10/16/2016 by GLEN

I WOULD LIKE TO REPLACE MY MARATHON C1245 MOTOR WITH YOUR PL 2102 model. is it compatible? I noticed my current sf is 1.25 and yours is 1.00 .also my SFA is 14/7 and yours is 15/7.5
 Reply

A  Answered on 10/18/2016 by InyoPools Product Specialist Adam Y.

Glen, Yes this pump pl2101 is compatible with your C1245 marathon.
 Reply


?     Asked on 10/13/2016 by Kathy

Will this motor replace Max-E-Pro P6EA6E-205L
 Reply

A  Answered on 10/13/2016 by InyoPools Product Specialist Lennox H.

Hi Kathy. Yes, the PL2102 motor can be used as a replacement for the Max-E-Pro P6EA6E-205L pump.
 Reply


?     Asked on 9/27/2016 by Sherrie Jans

will this motor replacement work for pentair Max-E- Pro pump model # P6RA6E - 205L ?
 Reply

A  Answered on 9/28/2016 by InyoPools Product Specialist Stacey M.

Hello Sherrie, Yes that is the replacement motor for a P6RA6E-205L pump.
 Reply


?     Asked on 1/19/2012 by Guest

I'm trying to replace the motor on my pool pump but all these numbers and abbreviations on the motor label are really confusing me. What do they mean?
 Reply

A  Answered on 1/19/2012 by InyoPools Product Specialist Patrick P.

Replacing a pool pump motor is not as difficult as it seems. You can try looking here. If you need help figuring out what the information on your label means. If you are still having difficulty figuring it out you can call us at our toll free number or you can send us a photo of your motor label here.
 Reply


?     Asked on 1/12/2012 by Guest

Why should I purchase a Tune Up Kit?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
 Reply


?     Asked on 1/12/2012 by Guest

Why do I need to purchase a new shaft seal?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
 Reply


?     Asked on 1/11/2012 by Guest

What is Service Factor?
 Reply

A  Answered on 1/11/2012 by InyoPools Product Specialist Patrick P.

Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
 Reply


Top

Review Summary

 (Average 3  out of 5 stars)
1 Ratings
5 star:
 
(0)
4 star:
 
(0)
3 star:
 
(1)
2 star:
 
(0)
1 star:
 
(0)