I have (I think) a Hayward C12002 filter system on my pool, the pressure gauge looks like this one but it also has two extra levers. The needle appears to be stuck and I feel I should replace the gauge. Will this one fit my filter
Reply
Yes this gauge will work for this filter model.
Reply
will this guage work on a Pacific Hydrostar 1hp shallow well pump?
Reply
Hi, The Back Mount Pressure Gauge 0-60 1/4" NPT (102D-204D) can work on a Pacific Hydrostar if the guage port can support a 1/24" NPT thread size.
Reply
Does this pressure gauge work with the 500?
Reply
Hi Nancy, The Back Mount Pressure Gauge (102D-204D) can work with a number of filters and valve. If you can provide a specific manufacture and model of the unit you're referring too I can confirm if this pressure can work with that unit.
Reply
will this gauge work on Vari Flo XL?
Reply
Hi Gary, for the Hayward Vari Flo XL you would need the 4726-0 Pressure Gauge.
Reply
my gauge blew. the top of my filter housing blew its top. it is old/rusty. what do i do?
Reply
When the filter is dirty, the pressure in the filter builds indicating it needs to be cleaned. Since the gauge was not functioning and this event happened, you will need to be looking for damage to the filter tank as well as the valve assembly. Once you have that information, you will be able to determine if it would be better to replace damaged parts or to replace the entire unit.
Reply
Will the pressure valve work with a haywood swimxpro voyager sw100z4
Reply
Hello Don, the one for your filter hayward swimpro is ecx27091, depending on your threads that you have currently please check the specs on your 4727-0 with 1/4" threads.
Reply
how do replace this item
Reply
Hi. Replacement steps can be found in our How To Replace a Pool Filter Pressure Gauge guide.
Reply
what is the correct installation method to replace this gauge?
Reply
Here is our How To Replace a Pool Filter Pressure Gauge on a Cartridge Filter guide which should assist you step by step. Please note that this procedure may be general per your specific application but does go over the main points on replacing these on any filter.
Reply
I have a Blue Wave NE636 cartridge filter system. My pressure gauge needs replaced, but this gauge, #4727-0, says it is 0-60. My present dial reads from 0 to 40. so will this gauge work as a replacement (I see that the inner dial does have 0-40 reading)? The replacement part number shown in my manual say that i need a part #BS 39349.
Reply
This gauge has the readout of 0-60 psi.
Reply
my original pressure gauge has a dial that reads 0 to 40. Will a gauge with 0 to 60 perform the same function, only with a smaller scale (the 0-10 increment spacing is smaller on the 0-60 gauge than it is on the 0-40 gauge)
Reply
Hi. Yes, it will perform the same function. The gauge must be used for the correct application.
Reply
Hello,
I have a Haywood Star Cleaner Plus Filter Model C1200, will this gauge fit. You can also see that I keep Plastic over it reference it rusts.
Yes, this pressure gauge will fit your model filter.
Reply
I need a new gauge and a sight glass. Please look at the picture and tell me what I need to order. Thanks in advance
Hi Tammy, This 4727-0 Pressure Gauge is the correct pressure gauge for your Jacuzzi 39263105 valve. You will also need this Jacuzzi Site Glass
Reply
Need to replace the pressure gauge on a SwimPro Voyager 150 series filter tank (SW150MDDVPAKS). Original part seems to be a Hayward ECX27091. Gauge is directly exposed to rain. Not interested in a Hayward brand part. What non-Hayward replacement gauge do you recommend? Thanks.
Reply
Yes, this gauge would be a good replacement for your pressure gauge.
Reply
I've replaced this gauge in my Hayward Voyager Pro w/ CCX2000RE cartridge several times using identical replacement gauges bought at a local Big Box store, and I'm not satisfied with it (it mounts flat, directly in the housing). Isn't there a gauge that stands up on the housing, perhaps using an adapter?
Regards,
Reply
Unfortunately, the back mount pressure gauge design is what this filter model was designed to use.
Reply
What pressure guage do I need for a Hayward C19002SBH?
Reply
I have a Hayward Pro Series High Rate Sand Filter, model S-310S. I need a new pressure guage. When I enter the part number for the pressure guage, (ECX2708-6-1) two guages have come up. One is for $30, and one is for $8.33. Which do I need?
Thanks,
Larry
Reply
Hi Larry, some of these gauges are original Hayward manufactured versions and others a generic manufacturer but essentially any bottom mount gauge will work.
Reply
Replaced my Hayward 36ft pro grid de filter gauge with this one but the pressure reads real low.
Reply
Hi Leo, it may be that the gauge is defective or that your filter actually does run with a low PSI. As long as you have good suction and water pressure at your pool returns then I would not be concerned about it.
Reply
Will this pressure gauge fit Valve Assembly TA60Dog Six-Way Valve 272523 for a Pentair Sand Filter Number 145241?
Reply
Hi Michael, Yes this is the correct replacement gauge for your Pentair Filter / Valve.
Reply
Hi. Will this gauge fit the Hayward SwimClear C2030, C3030, etc series of filters? Also looking for filter replacements. I believe CX875 is the filter - would you please confirm?
Hello Gerry. Yes, the Back Mount Pressure Gauge 102D-204D is compatible with the Hayward SwimClear Quad Filter System. It is unclear which model SwimClear is pictured, the label does not designate. Attached please find a parts diagram for the Swim Clear Quad Filter Series. Replacement filter cartridges are listed under Key #13. Each option identifies cartridge dimensions for comparison to your filters. Hayward SwimClear C2030, C3030, C4030, C5030, C7030
Reply
will this work on hayward c-1500 star clear ll
Reply
Hello Linda, yes this pressure gauge is compatible with your Hayward Star Clear filter model C-1500. I have also emailed you an estimate that you can convert to an order if you would like. Item is in stock and ready to ship.
Reply
Will this replace the gauge on a Hayward Pro-Grid (DE4820)?
Reply
Hello Richard, yes this pressure gauge is compatible with your Hayward ProGrid D.E. Filter model DE4820. I have also emailed you an estimate that you can convert to an order if you would like. Item is in stock and ready to ship.
Reply
.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-1eec81de-0052-437f-8882-04b95392290f.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Engineered Specialty Products Pool Filter Pressure Gauge, Rear Mount, 0-60 PSI, 1/4\" NPT - 102D-204D")
-1eec81de-0052-437f-8882-04b95392290f.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Engineered Specialty Products Pool Filter Pressure Gauge, Rear Mount, 0-60 PSI, 1/4\" NPT - 102D-204D")