I have a purex triton tr60 filter with a purex 27-1140 multi valve. This looks like the
haywood 1 1/2 4700-15x. Am I correct in looking at this part?? I need to replace my valve, just want to make sure this is correct. Also are parts available for the filter if I need them/ which filter do i need to look for.
Reply
Hi Ken, Part # 27-1140 is the part # for the label which goes on the Pac Fab 1.5" sand filter Hi-Flow valve. We do sell the Top Assembly for the Hi-Flow Valve We do carry the Complete TR60 Valves here but there are a few options based on the year of the filter and your thread types. And....yes we do carry all of the Replacement Parts for Triton TR Series Sand Filter.
Reply
how can I tell if this is the correct part for my valve with the lable worn off?
Reply
Hi, If you can locate and provide any part numbers that is on the valve body to be used as a reference to confirm if this part will fit.
Reply
Hello I currently have a Hayword SP-710 Vari-Flo Multiport Valve. The handle is loose, the steel pin is coming out, the handle is extremely hard to turn, and there is leakage to the backwash hose . I would rather replace the entire valve instead of taking apart and fixing parts, and read that I need a "key assembly" to do this. Can you point me to the right part that I need?
Reply
Hi, Lynne. You can use this Cover Assembly - SPX0710XBA along with the Diverter Gasket - SPX0710XD and Cover O-ring - SPX0710XZ3 to rebuild your SP710 Valve. However, if you would like to replace the entire valve I will need to know the filter model to make sure we get you the correct valve.
Reply
Hello,
I have a multiport valve on my Nautilus NS 36 DE filter.
I am not sure of the make or model; the documentation I have says Hayward SP-710 Vari-Flo but the only writing I can read on the valve itself says PacFab and a number 3640310. The valve is white with ports on side and bottom, side goes to top port on filter and bottom goes to bottom on filter.
If you can figure out which valve I have I would like to either replace it entirely or rebuild it with a new Key/Cover assembly etc
Reply
Hi, Martin. You can use the Vari-Flo - SP0710XALL complete valve or this Cover Assembly - SPX0710XBA to either replace or rebuild your valve.
Reply
Can I use this part to rebuild my multiport valve?
The valve is mounted on the sand filter side. I do not have any valve documentation. I can read the following marking on top of the valve:
PAC-FAB SP-710 Sand
Patent 3,640,310
Operating Pressure 75 psi
Rated Flow 75 GPM
Reply
Hi, KathyP. Yes, you can use this Key, Cover, & Handle Assy - SPX0710XBA with your valve. You will also need the Cover O-ring - SPX710Z3 and or the Valve Seat Gasket - SPX710D.
Reply
Will this item replace Sp710x62?
Yes, the SPX0710XBA is compatible with the SP710 series valves.
Reply
Is this part that is showing turning when I click on it the complete valve assembly? I have a pool that has a sand filter and it was here when i purchased the property in 2001. A leak developed after the back wash was performed recently. The only legible descriptions I can read are, Hayward, NSF model SP 710. The dimensions listed on line (tip of handle to tip 63/4") and between screws 61/4 and 4 inch are same.
Best Regards,
Bill Armes
Reply
Hi, Bill. This Cover, Key & Handle Assy. 1-1/2", White - SPX0710XBA will fit your model SP 710 valve. You will also need the Cover O-ring - SPX710Z3 and or the Valve Seat Gasket - SPX710D or SPX0710XD.
Reply
Looking at the bottom of this valve in your photos it looks like it has 4 spokes. What will be the correct o-ring and bottom spoke gasket be? looks like you sell a 6 and 5 spoke gasket only?
Reply
