Is there a quick reference or instruction guide for installation of the temperature sensor,IID unit?
Reply
Hi Bob, Page 11 of This Manual may help.
Reply
My inground pool heater says sensor failure and will not start. Where is the problem and how do I fix it?
Reply
Could you let us know the make and model of your heater and approximately how old it is?
Reply
I have a Raypak pool heater, model P-R335B-EN. It has stopped heating and has a fault code SNS - sensor. What is the replacement part number and the cost? I have no manual could send me a copy?
Thanks
Reply
Hi, Larry. Based on the model number of your unit and the error code, you will need to replace the Temperature Sensor - 005088B.
Reply
I have a 2014 Raypak 406a. The display shows sensor failure and the unit will not work. The display is still showing water temp correctly. Is this a temperature sensor failure or is there another sensor? Thanks
Reply
Hi, Todd. If the unit is reading the correct temperature, the sensor may not be the issue but the circuit board. I would recommend troubleshooting the unit using the Steps on Page 46 of the Raypak Owners/Instructions Manual.
Reply
I have a Raypak P-R266A-EN-C pool heater. I am getting SNS error code. Do you carry a replacement sensor for this model? Is this part easily replaced by an HVAC licensed contractor? Or should I consider purchasing a new heater?
Reply
Hi, Karenlee. We do sell the replacement Temperature Sensor - 009577F for your unit which can easily be replaced by an HVAC licensed contractor. I would not recommend replacing the unit if the temperature sensor or circuit board is bad, they can be replaced.
Reply
My pool heater is reading the water temp way higher than it actually is, which keeps the heater from kicking on. The digital screen says “sensor error”. Essentially the internal sensor isn’t reading the water temp correctly which keeps the heater from kicking on. Am I safe to assume I just need a replacement sensor? Thank you!
Reply
Hi Nic, Yes this would be we would suggest replacing as the temperature sensor is a common part that goes bad. You just need to confirm that you purchase the proper temperature sensor for your model heater.
Reply
I need a temperature Sensor for Raypak P-R206AMN-C pool heater
Reply
Hi, Bill. The Thermostat Control - 003346F will be the replacement for your P-R206AMN-C model unit.
Reply
I installed new sensor, part number 009577F. When I turn on pump, water leaks out of fitting nut and sensor raises high above the top of the nut. What did I do wrong?
Reply
My heater wont fire and shows error sns off
Will the Temperature sensor, IID units 009577f fix this problem?
Reply
Hello, We recommend contacting the manufacturer on that question. You can reach them at 805-822-8894.
Reply
I have a raypak Model: P-R266A-EN-X S/N 1402214352. I don't remember when I purchased it but I did buy it from INYO Pools. When I fired it up yesterday, it sparked and ignited then heated. The water temp rose to 230 degrees. then the messages "Sensor failure" followed by "Sensor Shorted". Sounds like a Thermistor, which one? I also need a new Control Bezel. are either of these a DIY project?
Reply
Hi, Michael. This Temperature Sensor - 009577F along with the Control Bezel w/ Decal (05/2011-Present) - 013491F are the correct parts for your unit based on the model and serial number. Replacing these parts is a DIY project.
Reply
I bought a replacement sensor for my RP2100 but can’t figure out where it goes. Any help would be great. Thanks
Reply
Raypac 266 ng indicates “low temp 35 lockout “ and will not turn on heat. Can you help? Thank you.
Reply
We apologize for the inconvenience, but our technicians are not certified to troubleshoot RayPak units. We suggest getting in touch with the manufacturer directly and speak with their technicians. RayPak can be reached by calling 805.278.5300.
Reply
I have a Raypak 266A heater and I'm getting the 'Sensor Failure' code. I just replaced the LCD screen which wasn't working (I believe) because of moisture damage. Is the Sensor Failure related to the LDC screen replacement?
Reply
Hi, Andrew. It is not, the sensor or the PCB could be bad. You can troubleshoot the temperature sensor using the instructions on page 46 of the Raypak Owners/Instructions Manual.
Reply
I have a Ray Pak 2100, it ignites and gives off an excellent flame, produces a lot of heat but it only raises the water temperature 5 degrees from 71 intake to 76 going back to the pool. I was told by Ray Pak it could be the "Unitherm Governor" which is similar to the thermostats in a small block Chevy, I removed it and it made no difference, I would be greatful for any suggestions you might have? Phil
Reply
Unitherm Governor, Raypak 105A/105B/155A/185A/R185/185/207A Horizon # 47-197-1416 also bypass valve spring 47-197-1615 Bypass Spring, Raypak 185A/R185/207A/206A 47-197-1422 Bypass Spring, Raypak 105A/105B/155A/185A/R185/207A/206A located just below Governor
Reply
Can this sensor be cleaned by light sanding
Reply
Hi Mike, we would not recommend sanding these sensors however using diluted acid to water mixture of 1 part muriatic acid to 5 parts water to clean any scale off of it.
Reply
Hi! I lost my user manual for my Raypak heater so I don't know for sure if this sensor will work with my heater. It looks the same but I just wanted to be sure it is an exact match. Do you know which Raypak heater models use this sensor? Thanks!
Reply
Hello winter, this unit would work on the Raypak R106A & R156A (6/01/13-Current).
Reply
