Temperature Sensor, IID Units - 009577F

$102.99

IN STOCK
FREE SHIPPING

Part # 6238-014

By Raypak


Details

Top

Part # 6238-014

Manufacturer Code 009577F

Dimensions 5.5" L x 4" W x 2" D

Alternate Part #'s 009577F

Product Description

3 WIRE, GREEN, GREEN, BLACK

Top

?     Asked on 6/6/2019 by Andrew

I have a Raypak 266A heater and I'm getting the 'Sensor Failure' code. I just replaced the LCD screen which wasn't working (I believe) because of moisture damage. Is the Sensor Failure related to the LDC screen replacement?
 Reply

A  Answered on 6/6/2019 by InyoPools Product Specialist Lennox H.

Hi, Andrew. It is not, the sensor or the PCB could be bad. You can troubleshoot the temperature sensor using the instructions on page 46 of the Raypak Owners/Instructions Manual
 Reply


?     Asked on 5/24/2019 by Michael S Harb

I have a raypak Model: P-R266A-EN-X S/N 1402214352. I don't remember when I purchased it but I did buy it from INYO Pools. When I fired it up yesterday, it sparked and ignited then heated. The water temp rose to 230 degrees. then the messages "Sensor failure" followed by "Sensor Shorted". Sounds like a Thermistor, which one? I also need a new Control Bezel. are either of these a DIY project?
 Reply

A  Answered on 5/24/2019 by InyoPools Product Specialist Lennox H.

Hi, Michael. This Temperature Sensor - 009577F along with the Control Bezel w/ Decal (05/2011-Present) - 013491F are the correct parts for your unit based on the model and serial number. Replacing these parts is a DIY project. 
 Reply


?     Asked on 3/12/2019 by Dwight MI Drake

I installed new sensor, part number 009577F. When I turn on pump, water leaks out of fitting nut and sensor raises high above the top of the nut. What did I do wrong?
 Reply

A  Answered on 3/13/2019 by InyoPools Product Specialist Lennox H.

Hi, Dwight. Not sure what you did wrong, it sounds like the Sensor Adapter - 006714F may need to be replaced. Also, inspect the manifold to make sure that the threads are not stripped. 
 Reply


?     Asked on 5/31/2018 by Bill Lillyman

I need a temperature Sensor for Raypak P-R206AMN-C pool heater
 Reply

A  Answered on 5/31/2018 by InyoPools Product Specialist Lennox H.

Hi, Bill. The Thermostat Control - 003346F will be the replacement for your P-R206AMN-C  model unit. 
 Reply


?     Asked on 5/23/2018 by Nic

My pool heater is reading the water temp way higher than it actually is, which keeps the heater from kicking on. The digital screen says “sensor error”. Essentially the internal sensor isn’t reading the water temp correctly which keeps the heater from kicking on. Am I safe to assume I just need a replacement sensor? Thank you!
 Reply

A  Answered on 5/23/2018 by InyoPools Product Specialist Patrick P.

Hi Nic, Yes this would be we would suggest replacing as the temperature sensor is a common part that goes bad. You just need to confirm that you purchase the proper temperature sensor for your model heater.
 Reply


?     Asked on 5/14/2018 by Karenlee

I have a Raypak P-R266A-EN-C pool heater. I am getting SNS error code. Do you carry a replacement sensor for this model? Is this part easily replaced by an HVAC licensed contractor? Or should I consider purchasing a new heater?
 Reply

A  Answered on 5/15/2018 by InyoPools Product Specialist Lennox H.

Hi, Karenlee. We do sell the replacement Temperature Sensor - 009577F for your unit which can easily be replaced by an HVAC licensed contractor. I would not recommend replacing the unit if the temperature sensor or circuit board is bad, they can be replaced. 
 Reply


?     Asked on 4/29/2018 by TODD SHAW

I have a 2014 Raypak 406a. The display shows sensor failure and the unit will not work. The display is still showing water temp correctly. Is this a temperature sensor failure or is there another sensor? Thanks
 Reply

A  Answered on 5/2/2018 by InyoPools Product Specialist Lennox H.

Hi, Todd. If the unit is reading the correct temperature, the sensor may not be the issue but the circuit board. I would recommend troubleshooting the unit using the Steps on Page 46 of the Raypak Owners/Instructions Manual
 Reply


?     Asked on 7/31/2017 by Larry Jones

I have a Raypak pool heater, model P-R335B-EN. It has stopped heating and has a fault code SNS - sensor. What is the replacement part number and the cost? I have no manual could send me a copy? Thanks
 Reply

A  Answered on 8/1/2017 by InyoPools Product Specialist Lennox H.

Hi, Larry. Based on the model number of your unit and the error code, you will need to replace the Temperature Sensor - 005088B
 Reply


?     Asked on 6/6/2016 by

My inground pool heater says sensor failure and will not start. Where is the problem and how do I fix it?
 Reply

A  Answered on 6/7/2016 by InyoPools Product Specialist Patrick P.

Could you let us know the make and model of your heater and approximately how old it is?
 Reply


?     Asked on 5/20/2016 by Bob

Is there a quick reference or instruction guide for installation of the temperature sensor,IID unit?
 Reply

A  Answered on 5/21/2016 by InyoPools Product Specialist Patrick P.

Hi Bob, Page 11 of This Manual may help.
 Reply


Top

Review Summary

 (Average 0  out of 5 stars)
0 Rating
5 star:
 
(0)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)