Part # UQS1202R
Warranty 1 Year
Dimensions 14" L x 9" W x 7" D
Alternate Part #'s 12042, AE100GLL-Y, B964, K48M2P105, K48M2P105B3, K48M2P108, UQS1202R
THE USQ1202R 2HP UPRATED MOTOR HAS BEEN REPLACED WITH THE SQS1152R 1.5HP FULL RATED MOTOR. THE TOTAL HP ON BOTH MOTORS ARE THE SAME
Voltage 220, High Speed HP = 2 Low Speed HP = 1/3, Max Amps @ High HP = 10.0 Max Amps @ Low HP = 3.5, Dual Speed, Square Flange, RPM @ High Speed = 3450 RPM @ Low Speed = 1625, Threaded Shaft, Frame = 48Y Used on the following models: Sta-Rite Max-E-Glas, Max-E-Glas II, Dura-Glas, Dura-Glas II, Dyna-Glas, Dyna-Max Pentair Whisperflow, Pinnacle and Anthony AR2 Series.
This motor does not come with a Hi/Lo switch. The part number for the switch is part number 1011431-001.
Hello,
I need to replace my motor and need your help identifying the right replacement motor. What other items should be replaced with a new motor?
I included a picture of the motor's tag for your reference.
Thank you,
Mike
Reply
Hi Mike, it seems as if the photos did not upload successfully. Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Here are the photos of the motor.
The Century 1.5 HP Square Flange 56Y Full Rate Motor (115/230 Volt) - B2858 with Whisperflo - GOKIT32 or Whisperflo Saltwater - GOKIT32SALT Frequently Bought with this Shaft SealClear RTV Silicone 6558-0 (For gluing shaft seal into the seal plate). The California Title 20 Compliant Options: Dual Speed 230 Volt - B2983 or Variable Speed (208-230V) - ECM27SQU How To Understand True Pump Horsepower - Up Rated vs Full Rated
Reply
Hi,
My motor froze up and I need to replace it. I have a saltwater pool and have included a photo of the motor. What else do I need to replace when replacing a motor?
Thank you for your help,
Mike
Reply
Thank you for the information on your motor. To better assist you, we will also need the make and model of your pump. This information is typically listed on a label on the housing area, opposite the motor. Once we have this information, we can better answer your questions/concerns. Please let us know if you need help locating this information on your pump.
Reply
Hi. Will this pump fit my Sta-Rite P6RA6YG-207L dual-speed, 2hp pump?
Reply
Hi Paul, yes, this is the correct dual speed replacement motor for the motor on the P6RA6YG-207L . You will also need a Sta-Rite Max-E-Pro tune-up kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Which impeller is best fit for this motor to be used with a Sta-Rite Dura-Glas II pump?
Reply
Hi John, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
I have a WhisperFlo model WFEDS-8 and I am trying to replace the motor. The old model number is UQS1202R. I also need to know what additional parts I might need to replace the pump. The pool is about 12 years old.
Any help would be appreciated.
Thanks in advance.
Reply
Hi Ross, most commonly the motor and seals are replaced when replacing a motor. For your Pentair Whipserflo model pool pump the seal kit for a chlorine swimming pool is the GOKIT32 and for a saltwater pool is the GOKIT32SALT.
Reply
how do you tell the difference between a 48 y and a 56y and just what dose it mean
Reply
ihave a p6e6g-208L 2hp need to replace i live in california and was told its not compliant .what is the correct model number
Reply
Hi, Scooby. The Dual Speed replacement motor options are the SQS1202R or the B2984 motors, this UQS1202R motor will not with your model pump. You will also need to get the Max-E-Pro Pump Tune Up Kit - GOKIT79. As for the complete pump, the P6RA6YG-207L is the closest option.
Reply
Will this replace a Starite Max E Pro 2 - 1/4 hp pool pump motor?
Pump model number P6RA6YG-207L
Reply
I have this pump which I bought from you three years ago. It will start in the low speed but will not start in the high-speed. Once the motor is running in the low-speed I can switch it to the high-speed but I'm wondering what the problem is and if there is a simple solution to be able to start directly in the high-speed. Thank you
Reply
Hi, Brooks. The only thing that I'm aware of that can cause this issue is a bad capacitor.
Reply
My current motor is a 56Y square flange. Will this 48Y square flange motor fit on my existing Pentair Whisperflo pump?
Reply
Hi, This motor will fit the Pentair Whisperflo pump, you will have to use the motor pad that comes with the motor so that it sit leveled on the motor base. I will also recommend that you get the Pentair Whisperflo Tune Up Kit GOKIT32 or GOKIT32SALT.
Reply
Which terminal should each of the three wires be placed? There is (black) (White) (Blue) or does it matter what terminal you would place the three wires
Reply
Nick, the placement of the wires will vary. You will need to know which one is your high, low and common lines. Typically L2 would be the common, L1 is the high and A is the low speed. Please double check the wiring diagram on the motor label before wiring.
Reply
I'm trying to replace the motor on my pool pump but all these numbers and abbreviations on the motor label are really confusing me. What do they mean?
Reply
Replacing a pool pump motor is not as difficult as it seems. You can try looking here. If you need help figuring out what the information on your label means. If you are still having difficulty figuring it out you can call us at our toll free number or you can send us a photo of your motor label here.
Reply
How can I tell whether or not my motor is a dual or single speed?
Reply
Most dual speed motors will have a toggle switch that will allow you to adjust the motor speed to either high or low. Another way to tell if your motor is dual speed is by looking at the RPM's on the motor specifications label. If there are two RPM's listed such as: 1725/3450 then motor is dual speed. If there is only one RPM, then motor is single speed.
Reply
Can you direct me to the proper hi low switch for this motor?
Reply
Unfortunately the manufacturer does not offer the switch for the 2 speed 220v motors any longer. If you already have a 220 volt timer (on/off) you would need an Intermatic T106R to switch from high to low speed. If you do not have a timer currently you would need the T10604R which is a 220v on/off timer and a high/low timer.
Reply
Why should I purchase a Tune Up Kit?
Reply
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Reply
Why do I need to purchase a new shaft seal?
Reply
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
Reply
What is Service Factor?
Reply
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Reply
Can you replace single speed pump motor with dual speed pump motor?
Reply
Yes but you can't go with a higher HP than the single speed motor. For example if you have a 1 HP single speed you cannot go with a 1.5 HP dual speed motor; you would be able to use a 1 HP dual speed motor. Customer would need to purchase a toggle switch or timer to switch from high speed to low speed.
Reply
The Most Helpful Review
5 0
(5 out of 5 stars)
Reviewed By: Charles E J. from Sugar Land, TX ()
Motor replacement went well, replaced seal, re-installed motor, all went relatively quickly. Where I bogged down was rewiring from a single speed motor to a two speed. Finally, I got the wiring straightened out and the pump would not pump water....found out after much effort, that part of the DE in my filter had plugged up the filter, when I drained everything down to change the motor. Backwashed filter (after I got water moving through it) and everything now works GREAT!!! Great item, quick delivery...it does everything as advertised, I left the pump running all day after the installation, for a very low electricity usage, and the water looked clean and crisp...that was on the slow speed. I have set the timer to run the pump on low speed 8 hours and high speed one hour. So far it has significantly reduced my electical usage.
Was this review helpful to you?
The Most Recent Reviews
1 1
(5 out of 5 stars) Motor Replacement
Reviewed By: Brooks K S. from Oyster Bay, NY ()
Pros: Easy to replace
Was this review helpful to you?