Part # GOKIT1
Alternate Part #'s 65001, GO KIT 1, PL1001
Standard tune up kit for the Hayward Max-Flo pump includes the shaft seal and all o-rings, gaskets and lubricant.
We highly recommend replacing the shaft seal, o-rings and gaskets when replacing your motor. If you use your old shaft seal, it will not mate up properly with the new motor and may leak.
This Tune Up Kit Works on These Pumps:
Tune Up Kit Includes:
Click here for Saltwater Pool Tune Up Kit (GOKIT1SALT)
For More Pool Pump Motors
I am ordering a replacement 1 1/2 HP Hayward pool pump motor Model #C48L2N134B3 and was told this is model 1152. I have an order on line for this pump but was asked if I need seals. I said yes and your man wanted the motel of the pump. I got the Hayward model
# SP3010X15AZ and Serial # 21111111050852007. My question is what seal part number do I need to order that fits the motor and pump?
Our pool jets are shooting aerated water, thinking may need to replace pump seals. Ours is a Max-Flo pump. What kit would you recommend?
Hi Jeanne, yes the Tune-Up Kit Hayward MaxFlo - GOKIT1 would be the correct seal kit for that pump.
Hello. I have a Hayward SPX2800AAC pump housing and a Century UST1102 pool motor, model C48K2N143C1C. Which kit do I need to replace the seals? I have included a picture of the plate on the pump. Thank you.
I need the gasket for the Max-Flo pump, model B C48K2n143, ser # 8f93. Its the gasket for the small basket where you prime it. thanks
Will this fit Hayward MaxFlo 1.5hp VSP sp2302?
I have an older Max Flo SP 2800 X 5 Which tune up kit do I need to order ?
The correct tune up kit for the Hayward Max-Flo Sp2800 is the Tune Up Kit Hayward MaxFlo - GOKIT1 or if you have a salt system, the Tune Up Kit Hayward MaxFlo Salt Pools - GOKIT1SALT.
I'm looking for a pool pump motor and the seal kit to install it.
The pump is a Hayward Maxflo
The motor is a AO Smith 3/4 HP MOD# C48J2N131B3
Are there instructions or a video on how to install the tune up kit?
I am looking for parts for my Hayward max flo ll The parts i need are (Hayward oem parts in parentheses) (GMX600F) Housing O Ring (SX220z2)Diffuser O ring and (SPX 2700s a) Shaft seal assembly. I would like to know if your tune up kit hayward maxflo are the same parts I am describing If so I would like to order it. Could you please let me know if these are the parts I need? Thank you
My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!
You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.
Does the motor and kit come with any instructions on how to change the motor on my pump?
The motor comes with a wiring diagram but here is a more detailed document on how to replace the motor, look under the section labeled seal change instructions. http://www.inyopools.com/owners_manual/hayward_pumps_inground_max-flo.pdf
Less than 1 hr
Screwdriver, Socket Set
1 to 2 hrs
Screwdriver, Nut Drivers, Socket Set, wire cuters with wire stripper
This was my first time installing a pool pump motor. What I did was remove and replace the motor and change out the old seals. When installing new seals I used the included seal lub. After installing motor I checked it out and looked for leaks. I took my time and was finished in less than a couple of hours. I did need to change out some house to motor electrical connections to get a better electrical contact, but all together it was a easy job.
(5 out of 5 stars) Seal replacement with new pump motor
Reviewed By: ()
This was my first time installing a pool pump motor. All I did was remove and replace the motor and change out the old seals. I took my time and was finished in a couple of hours. I did need to change out some motor electrical connections, but all together it was a easy job.