Top Mount Flanged Valve T-300BP - TM-22-L

$168.99

IN STOCK
FREE SHIPPING

Part # 4684-10A

By Praher

  5 Average  

Details

Top

Part # 4684-10A

Manufacturer Code TM-22-L

Dimensions 10" L x 10" W x 12" D

Alternate Part #'s 14971TM22L, 2280, STA06263, TM22L

Product Description

Top Mount Flanged Valve T-300BP - TM-22-L

24204-P242 (PANTERRA), AND 24205-P302 (PANTERRA). THIS VALVE FITS STA-RITE TANK MODEL#

Top

?     Asked on 8/22/2019 by mcarol gillespie

i need a replacement pressure gauge top for a sta rite T210 wf will this one work ?
 Reply

A  Answered on 8/22/2019 by InyoPools Product Specialist Joe S.

The gauge needed would be the Sr Pressure Gauge (33600-0023t) PART # 4680-23T
 Reply


?     Asked on 8/3/2019 by Barb

We have a StaRite above ground salt water sand filter. We do not know the model # but do have a serial #4230111070023P. The wind blew off the disk that sits directly below the handle which changes the flow from filter, rinse, waste, backwash etc. We cannot remember where each function sits. Could somebody please send a picture identifying the different positions. I have attached two pictures showing the filter in "filter" mode.

 Reply

A  Answered on 8/9/2019 by Industry Professional

See image, Sorry but we do not have a good picture & that valve is now discontinued & replaced by a different mfg valve ( 26-253-1030 )

 Reply


?     Asked on 5/31/2019 by Jack

What is the valve part number for a Sta-rite Cristal flo T-200BP-1? I was told the old valve is obsolete. The number on it is WC-112-148. Thank you for your time.
 Reply

A  Answered on 7/17/2019 by InyoPools Product Specialist Hector F.

The current replacement valve is 4600-1186.
 Reply


?     Asked on 5/23/2019 by Trampas

Is the TM-22 the same as the TM-22-L? Myine is just labeled as a TM-22 but I can’t seam to find anything but a TM-22-L.
 Reply

A  Answered on 5/25/2019 by InyoPools Product Specialist Patrick P.

Hi Trampas, Could you get the make and model of your filter? This should be on a label on the side of the tank of your filter. Just click the reply link below to supply this information and then we can confirm if this valve will work for you.
 Reply


?     Asked on 5/20/2019 by Phil

Will this multiport fit a Cristal-FLo model number T-240BP
 Reply

A  Answered on 5/20/2019 by InyoPools Product Specialist Patrick P.

Hi, Phil. The Cristal-Flo 240-BP filter comes in either 1-1/2" or 2" port size. If you have the 1-1/2" you'll need the TM-12-L or the TM-22-L for the 2" model.
 Reply


?     Asked on 5/8/2019 by

What does this part weigh? What are the weight and dimensions packaged? I am going to take this with me flying to Costa Rica and need this for baggage considerations. Thank you!
 Reply

A  Answered on 5/13/2019 by Industry Professional

The weight is 7.8 lbs, dimensions are 13.60" L x 10.4" W x 9.35" H. 
 Reply

  • Commented on 5/14/2019 by Product Owner

    Thank you!
     Reply

    • Commented on 5/15/2019 by InyoPools Product Specialist Patrick P.

      You're welcome, have fun in Costa Rica!
       Reply


?     Asked on 3/12/2019 by Dale

I need a replacement top assembly for a aquatools AT3125?
 Reply

A  Answered on 3/13/2019 by InyoPools Product Specialist Michelle B.

Hello, This will be the correct replacement for your filter. http://www.inyopools.com/Products/07501352059293.htm
 Reply


?     Asked on 3/12/2019 by Dale

I need a replacement top assembly for a aquatools AT3125?
 Reply

A  Answered on 3/13/2019 by InyoPools Product Specialist Michelle B.

Hello, This will be the correct replacement for your filter. http://www.inyopools.com/Products/07501352059293.htm
 Reply


?     Asked on 11/1/2018 by

Does this fit for aquatools AT 3130.?
 Reply

A  Answered on 11/2/2018 by InyoPools Product Specialist Lennox H.

Hi. Yes, this TM22L valve will fit the AT3130 model filter. 
 Reply


?     Asked on 3/8/2018 by Mary

Does this come with the spider gasket? If not, which model gasket do I get? Are their any other parts that are needed? thank you.
 Reply

A  Answered on 3/8/2018 by InyoPools Product Specialist Kevin G.

Hello, this part is the complete valve. 
 Reply


?     Asked on 6/6/2017 by Ron

I have a waterway sand filter on a carefree sand tank. we are getting sand in our pool and it stays cloudy since I replaced the sand this spring. The tank calls for 150 pounds of sand and that is what I put in. Could the valve be malfunctioning and allowing sand in pool?
 Reply

A  Answered on 6/17/2017 by InyoPools Product Specialist Lennox H.

Hi, Ron. A bad multiport valve will not cause a pool not to clear up or become cloudy. Confirm that the port are connected right and that you have adequate flow. Once you've confirmed that use a water clarifier to help clear up the pool.
 Reply


?     Asked on 5/4/2017 by Leonard Burke

I am about to replace my Sta_Rite multi port valve 14971-TM-22-L that just arrived from you. Is there a YOUTUBE Site that explains this? Also can I add some sand to my filter Cristal-Flo T-300BP-2 before I nstall the valve?
 Reply

A  Answered on 5/5/2017 by InyoPools Product Specialist Lennox H.

Hi, Leonard. Our How To Install a Pool Sand Filter guide will provide you with the steps needed to install this valve to your tank.
 Reply


?     Asked on 4/23/2017 by

I purchased the TM-22-L valve for my Sta-rite T240-BP-2 sand filter. Inspected the laterals, etc., and replaced the sand. I still have sand leaking into the pool. Some diagrams for the TM-22-L show a O-ring gasket (Part#19) between the standpipe and the TM-22-L valve. I purchased this gasket, & it did not fit my standpipe. How tight should the standpipe fit into the bottom of the valve - should it be a watertight fit, or should it just be a lose fit? What diameter standpipe is required?
 Reply

A  Answered on 4/28/2017 by InyoPools Product Specialist Lennox H.

Hi. The valve is supposed to fit tight over the standpipe assembly allowing water to flow one way. The diameter of the standpipe should be 2.3 inches
 Reply


?     Asked on 4/2/2017 by Tom

I have a Cratal-flo 240-BP is the part number 4684-10A the top mount that i need to replace my old one with? and does it come with the seal gasket? Thanks, Tom
 Reply

A  Answered on 4/4/2017 by InyoPools Product Specialist Lennox H.

Hi, Tom. The Cristal-Flo 240-BP filter comes in either 1-1/2" or 2" port size. If you have the 1-1/2" you'll need the TM-12-L or the TM-22-L for the 2" model.
 Reply


?     Asked on 6/30/2016 by Lynda

I have a 15 year old Aqua Tools sand filter. Model # AT3124. When I called the 800# listed on the filter body, it referred me to a Sta-Rite/Pentair 800#. My question: Is this top mount part what I need to replace my old one?
 Reply

A  Answered on 7/4/2016 by InyoPools Product Specialist Lennox H.

Hi Lynda, The Top Valve Assembly (261186) is the correct valve for the AT3124.
 Reply


?     Asked on 10/17/2015 by Gerardo

I have a purex triton tagelus ta 100 with a purex triton tm-22 top mount valve an i want to change the entire valve, it has a 2" pipes, is this teh correct valve?
 Reply

A  Answered on 10/19/2015 by InyoPools Product Specialist Lennox H.

Hi Gerardo, The Pentair 2" Top Mount Clamp Style Valve (261185) would be the correct valve for the Purex Triton Tagelus TA 100 filter.
 Reply


?     Asked on 1/8/2015 by Russell Oakes

Will this fit Sta-Rite sand filter T-240BP-1?
 Reply

A  Answered on 1/9/2015 by InyoPools Product Specialist Andy O.

No,the 4684-10A will will only fit the T-240BP-2. The valve you for your model T-240BP-1 need is part number 4600-1186 (261186).
 Reply


?     Asked on 5/2/2013 by Guest

Is this the right valve for a Sta-Rite Cristal Flo T300BP2? Is the valve for 2" plumbing?
 Reply

A  Answered on 5/2/2013 by InyoPools Product Specialist Patrick P.

Yes, the 4684-10A (TM-22-L) is the correct valve for the Sta-Rite Cristal Flo T-300BP-2. The valve has 2" female threaded ports.
 Reply


Top

Review Summary

 (Average 5  out of 5 stars)
1 Ratings
5 star:
 
(1)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Recent Reviews