Flow Switch Assy Intellichlor - 520736

$158.99

IN STOCK
FREE SHIPPING

Part # 9237-137

By Pentair Pool Products

  4 Average  

Details

Top

Part # 9237-137

Manufacturer Code 520736

Alternate Part #'s 520735, 520736

Product Description

FLOW SWITCH ASSY INTELLICHLOR (#N/A)

Top

?     Asked on 2/24/2020 by Paul

What flow rate is good? I have a window view on the pipe and I can see water going thru when I have the solar panels on it is less but still flowing ? how much neeed to be going thru to keep the low flo light off?
 Reply

A  Answered on 2/25/2020 by InyoPools Product Specialist Lennox H.

Hi, Paul. The flow range is 20 - 105 GPM. 
 Reply


?     Asked on 11/14/2019 by Chad

My IC-40 flow switch went bad a year ago. I bypassed the flow wire and it worked fine until now. Now my problem is the Cold Water light coming on and shutting off the cell. Water is 79 degrees F. I know I need to purchase a new flow switch but does the Cold Water light have anything to do with the Flow switch? Does it also measure temp?
 Reply

A  Answered on 11/15/2019 by InyoPools Product Specialist Lennox H.

Hi, Chad. The Temperature Sensor is built into the cell, NOT the flow switch. You will have to replace the entire cell in order to resolve this issue.  
 Reply


?     Asked on 5/28/2019 by dan householder

My pool has been open for 2 weeks and is perfectly clear and all lights are green.We had a rain storm and now the green salt light is flashing saying high salt level.What could be the problem ?
 Reply

A  Answered on 5/28/2019 by InyoPools Product Specialist Steve M.

Dan, the Green (GOOD) salt light is flashing this would indicate that there is too much salt in the pool. This may cause damage to pool related equipment and surrounding surfaces. In order to correct this issue, Pentair suggests diluting the pool water by draining some water from the pool, then refilling with fresh water. 
 Reply


?     Asked on 4/9/2019 by scott

I have an Ic40 and the percentage lights will not stop continuously flashing no matter what I push. Help?
 Reply

A  Answered on 4/9/2019 by InyoPools Product Specialist Michelle B.

Hello,When the percentage lights are blinking, the cell is in the low output mode, if the cell is controlled from an automation system, use the intellichlor settings to adjust, if not continue to press the more buttons to get the cell into the higher output percentages.
 Reply


?     Asked on 1/14/2019 by Pat

I have a 1C20 when turn on its flashes from green for Salt to Red on flow back and fourth and does not produce any chlorine can this be just a flow meter ? Thanks Pat S
 Reply

A  Answered on 1/15/2019 by InyoPools Product Specialist Lennox H.

Hi, Pat. Based on the info provided, the flow switch is the issue if you've confirmed that the filter is cleaned and no blockage in the flow through the cell. 
 Reply


?     Asked on 4/27/2017 by Torrance

Sense the flow switch for the IC40 has two probes. Does that mean 1 is for flow, and the other probe is for salt concentrstion. Or is there another switch you have to buy for the salt level
 Reply

A  Answered on 4/27/2017 by InyoPools Product Specialist Lennox H.

Hi, Torrance. The flow switch works when the two probes as you called it makes contact with each other similar to like a door or window magnetic sensor. There is another sensor inside of the cell that monitors the salinity level.
 Reply


?     Asked on 4/26/2017 by Torrance

Sense the flow switch for the IC40 has two probes. Does that mean 1 is for flow, and the other probe is for salt concentrstion. Or is there another switch you have to buy for the salt level
 Reply

A  Answered on 4/27/2017 by InyoPools Product Specialist Lennox H.

Hi, Torrance. The flow switch sensor do not relay the salinity level back to the system, it only monitors water flow when the two probes make contact just like a magnetic sensor. The salinity sensor is built into the cell and can not be replaced. You will have to replace the entire IC40 Cell - 520555.
 Reply


?     Asked on 8/16/2016 by David

is this for the IC40 ?
 Reply

A  Answered on 8/19/2016 by InyoPools Product Specialist Lennox H.

Hi David, Yes, this Flow Switch Assy can be used with the Intellichlor IC40 .
 Reply


?     Asked on 8/1/2016 by joseph walsh

I have an IC15 unit. The red flow light stays on constantly but the flow continues. My pool store says I need a new flow control unit. Does the same flow control unit fit all units or is there a special one for the IC15
 Reply

A  Answered on 8/7/2016 by InyoPools Product Specialist Lennox H.

Hi Joseph, Yes, all Intellichlor models uses the same flow switch.
 Reply


?     Asked on 3/1/2015 by Waldemar

Hi, we have a Pentair ic40. We have a problem that when we started on the System, all the lights are on, then after a few seconds, all the lights turn off again. Do you have an idea what could be the problem? It is the flow switch that could be damage? Thanks in advance , Waldemar
 Reply

A  Answered on 3/2/2015 by InyoPools Product Specialist Wes B.

Sounds to me like there's a power issue, first thing to check would be the power supply. Unplug the power supply cord from power center, check for 25-36 DC volts across the black and red wires, if the volt meter reads the correct voltage then the cell would need replaced, if the voltage does not read correct you will want to change the power supply. Thank you again for contacting us at InyoPools.
 Reply


?     Asked on 1/19/2015 by andrea

Is it difficult to repair the flow switch assembly on the Intellichlor?Does it come with instructions on how to disassemble and put back together correctly?
 Reply

A  Answered on 1/19/2015 by InyoPools Product Specialist Robert M.

Hello Andrea - The flow switch is not difficult to install. It will take 15-30 minutes to complete the installation. Installation instructions are included.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Channel locks

2     0

Flow switch stopped working

Written on 6/26/2017 by Guest

It was quite simple following the INYO Pools provided instructions. Removed the plastic cover that protects the wiring on the switch end. It's the thing with the fine metal pieces hanging down in the flow area. Cut the wires as instructed (close to the defunct meter) and splice them with the provided splicers. Screw in the new flowmeter. Make sure the arrows line up on the top, this is important. Put the plastic cover back on. That's it! The hardest part was getting the wires back in the plastic cover as there is extra length with the instructions. If I were to do it again I would cut the wire so it would be shorter.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4  out of 5 stars)
1 Ratings
5 star:
 
(0)
4 star:
 
(1)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)