What is the difference between the Aqua Logic and Pro Logic?
Reply
The main difference between the Pro Logic and Aqua Logic is that the Pro Logic can accommodate Hayward/Goldline's new Sense and Dispense module. The Sense and Dispense module will sense how much chlorine and pH is in your pool and dispense the proper amount of chlorine or pH back into your pool. You will require a Stenner liquid acid pump & tank or CO2 tank for the pH portion of sense & dispense. The chlorine portion of Sense & Dispense will be taken care of by the Salt Chlorine generator. The Pro Logic also has enhanced user interface over the Aqua Logic and is an overall upgraded system.
Reply
What is the ColorLogic Network Module designed for?
Reply
The ColorLogic network module is designed to be used with the new ColorLogic 4.0 lights and the ProLogic System. When used together the ColorLogic lights will display 101 color tones, 16 themed shows, while controlling light brightness, speed and movement. The 4.0 ColorLogic Lights can be seen here http://www.inyopools.com/lights_colorlogic.aspx. The ProLogic Systems & ColorLogic Modules can be seen here http://www.inyopools.com/sanitizers_pro_logic.aspx.
Reply
Do i just need the light and my current prologic controller which runs my pool filter and spa etc.. or do i have to have a separate controller for the colorlogic led pool light?
Reply
You can use just the ProLogic to control the ColorLogic light but you will only be using a fraction of the overall control capabilities. To get the complete control capabilities you would need to order the ColorLogic Gen. 4.0 light here http://www.inyopools.com/lights_colorlogic.aspx along with the ColorLogic Communication Module here http://www.inyopools.com/Products/02200000040136.htmWhen using the ColorLogic Communication Module with the ProLogic the ColorLogic lights will display 101 color tones, 16 themed shows, while controlling light brightness, speed and movement.
Reply
Can I install the Pro Logic myself?
Reply
The Pro Logic is a large, multifunction, high voltage control system. For safety reasons, it is very important that the Pro Logic be installed per NEC(National Electric Code) and local electrical codes. In addition, the Pro Logic must be configured (programmed) to control the particular equipment on your pool. Hayward highly recommends that the Pro Logic be installed by a licensed professional.
Reply
Will the Pro Logic control 2-speed filter pumps?
Reply
All Pro Logic models can be configured to control 2-speed filter pumps. Unlike other pool automation controls, no special relays are required. However, the 2-speed filter pump will require the use of 2 of the Pro Logic's high voltage relays. The installation manual contains complete instructions for configuring 2-speed pump operation and it is very important the instructions be followed in order to prevent damage to either the pump or control. Separate high speed and low speed time periods can be programmed and also the you can manually control the pump with a single button: Push once to turn the pump on in high speed mode, push again to switch to low speed (the pump must run a minimum of 3 minutes at high speed in order to properly prime), and finally push the button again to turn the filter pump off.
Reply
Does the Pro Logic provide freeze protection?
Reply
The Pro Logic can turn various outputs on when freezing temperatures are detected. This function is fully programmable including which outputs will turn on and also the temperature threshold. This freeze protection is normally adequate for areas that experience infrequent freezing conditions with temperatures that don't dip to far below 32ºF (0ºC). For all other systems, the pools should be shut down per normal procedures for the winter.
Reply
Will your Hayward PL-PS-4 ProLogic system control (communicate) with my Jandy VSP mod #VSFHP165JEP and my PAL-2000 LED LIGHTING SYSTEM?
Reply
Hi, Gary. The JandyFlo VS Pump and PAL-2000 Lighting System can communicate with the ProLogic Controller.
Reply
Does it come with T-CELL-15 or do I order separate?
Does it come with P-Kit flow switch or do I order separate?
Reply
Question about PL-P-4. Does it have 4 aux. relays in addition to pump motor and heater?
Reply
Hi. This controller can control 4 relays including the filter pump, and 1 heater.
Reply
One followup please. Will the circuit that controls the two actuators (for a spa, for example) use up one of the 4 relays?
Reply
Hi, Terence. It will not, the actuators has its own terminal block.
Reply