Part # 140264
Warranty 3 Yr. Tank
With Triton II, you'll join satisfied customers worldwide who have made Triton II the world's #1 selling filter. Please note: the model most commonly shipped is the almond color tank, not black as shown.
For More Pentair Filters
Hi folks, I have an old Fox pool sand filter, model f3-24-63, would this be the best replacement for that? Thanks in advance!
Hi. Bardski. This TR60 Sand Filter is a good for the Fox F3-24-63 model.
I have a Purex Triton FNS Plus with a white dot on the chart that lists the models under the model marked FNSP 60. I'm new to pool ownership. It came with the house. The housing on this unit is leaking (the bottom half). Trying to decide if that's normal in a fiberglas filter and if I should replace the housing or think about a new filter. I'm guessing the filter may be 15 years old. If we should replace, what do I look for when spec'ing a new one?
Hello, John. That is not normal for it to leak. You may replace the Tank Bottom Assembly 60 Sq Ft Fns Plus (170018). When the filter's are at the10+ year mark, the manufacturer's best recommend to replace the entire filter. The filter may be replaced with the FNS Plus 60 Sq Ft Filter w/o Valve - 180009. You may use the Pentair FNS Plus D.E. Filter Parts Diagram as a guide for other replacement parts, it also includes a listing of the multi-port or push-pull valves available for the filter. You may also find our How To Guides helpful.
On the other filters listed on this site above this one, they list the size of the filter plumbing connections. But for this Triton II TR60 Side Mount 24 Inch Tank I can't seem to find that anywhere. Are the connections for this filter 1 and 1/2 inch or are they 2 inch?
The filter plumbing connections for a sand filter would be based on the valve not the filter tank. You would need to order 261173 for 1.5" and 261055 for 2".
I have a TR 60 Filter that had broken laterals, sand in the pool, I cleaned the filter and replaced the laterals then refilled with sand 325 # set the valve and started the pump. My pool got very cloudy, less tan 12 inch visability. I took the top off the filter and half of the sand was gone. I rechecked the laterals all were good. attempted again with same results. What could be causing this?
Hi David, I would first start off by reading this Article on Getting Sand Back in Your Pool you may also want to check to make sure you didn't plumb the valve backwards, for example plumbing your inlet line into the outlet port on the valve and plumbing your outlet line into the inlet port of the valve.
what gallon size pool will this filter handle?
Hello, Nicole. The Pentair Triton II TR60 Filter has a turnover capacity of 30,240 gallons in 8 hours, with a max Flow Rate of 63GPM (Gallons Per Minute). Please click here to view the brochure for the Triton II Fiberglass Sand Filter.
I understand that Pentair has Titan II TR60 filters with Clearpro technology. I did not find a distinction on the your sight. Does this filter have "clearpro technology"? Thanks.
Hi, This unit does not have the "ClearPro Technology," however if you're interested in the TR60 with ClearPro Technology (140212) let us know and we can get you all the info needed to place an order.
What valve is required for this filter -How much$ - what is part number -how long to ship to fl. 32003?
Please review key number 39 on this parts diagram for your filter to see your options.
Do you have instructions for changing the sand in this filter?
Hi, You can get instruction in the Pentair Triton Fiberglass Sand Filter Installation and User's Guide or follow our How To Replace the Sand in a Pentair Triton 2 Side Valve Sand Filter Guide.
Is the sand purchased separately from the filter?
Hello. Yes the sand is purchased separately. The manufacturer's recommendation is No. 20 Silica Sand. The Pentair Triton 2 TR-60 uses 7 50 lb bags of sand - 325 lbs total. You can also purchase a Sand Alternative. Thank you.
label on the TR60 say 250pounds of sand . Here I see 325lbs. Which one is correct. What will be the reasons why the pool water jet are throwing a lot of air? When I open the filter air release valve the bubbles star disappearing but I close the valve air come out again. Thanks,
Hi Ed, If the label on your filter states 250 lbs of sand then I will go by that. You have an air leak, I would recommend replacing the o-rings on your pump.
Is pea gravel necessary or could you use all sand?
Hello Wardell, The sand filter does not require Pea Gravel but it does help with filtration and removing the larger debris in the pool.
What is the setting when in operation?
The valve setting for normal operation would be "Filter".
When should I change the sand in my filter?
You should change the sand in your filter every 5-7 years. You can generally tell that it is time if your pool water is not as clear as it normally is or when you notice the interval between backwashes is shorter. You can use > this guide to walk you through it.
How many pounds of sand does this filter require?
If you are using all sand, it takes 325 lb. You can also use a mix of 75 lb pea gravel and 250 lb sand.
(5 out of 5 stars)
Reviewed By: Robert P. from Rincon, GA ()
Pros: Works great. Easy to install.
Very easy to do and saved me hundreds of dollars of what my poolman wanted. I replaced an old TR60 with this new one so the piping was already done. Took me 20 minutes. Works like a charm.