Model # 160318
Warranty 1 year
Alternate Part #'s 159303, 16-0318, PAC-05-504, PEN160318
The CLEAN & CLEAR Cartridge Filter features a thermoplastic chemical resistant tank with no-tool servicing and a coreless cartridge for easier cleaning. All models are equipped with easy spin-on unions for plumbing hook-ups. These filters are NSF listed for commercial applications and are available in 50, 75, 100, 150, and 200 square foot sizes.
Additional features include:
Click here for more Pentair Filter
Have a older Pentair clean and clear pool filter system, the cartridge filter for the unit is model is CC200. I need a new O-ring for the head however I can't find a model number for the unit. There is a P/N 178555 REV E listed on the side of the cover. In addition, I need the air sock that goes with it. Any idea where to find this stuff?
down bottom out put came off ,how can i put it back back and it will stay there ? Thanks
Hello, Here is a parts list for the heater: http://www.inyopools.com/pool_parts_pentair_clean_clear_predator_system.aspx Can you please indicate which key # you are referring to?
may i purchase the top only for a cc200
Thomas, You can find the lid for the Clean and Clear manufactured after 1998 here: http://www.inyopools.com/Products/07501352020754.htm
On the dimension drawing a diameter of 15.5 inches is shown below and outside the mounting base. Is this the base diameter or outside diameter of the clamp ring, a big difference? I have a clearance problem and need to know which is the 15.5. Thank you
Hi Charles, The 15.5" diameter is the base diameter not including the ring. The diameter is 17" including the ring.
is the only difference between the pentair 160318 and 160317 the filter inside? It appears the whole filter assembly is the same but with a 200 filter in the 160318 and a 150 in the 160317. Can you confirm that?
Correct the filter will be larger on the 200 but they are going to be the same Dimensions
Do filters and pumps go together size wise, or can you use the same pump with different filters. I have a small pool, I think it is 12,500 gallons but it has the CC 200 filter on it. So basically I'm asking if I can downsize the filter without the pump damaging it? Or do I just buy the same size filter unit even though its completely over-sized.
Hi, The filter is sized to meet or exceed the flow rate of the pump. If you down size the filter but the pump flow rate exceed the flow rate of the filter it can create back pressure. Your filter would have to be cleaned and replaced often, your pool would not be effectively filtered which can lead to other problems. It is better to over-sized the filter rather than under-sizing it.
Is there a warrenty
Thank you for asking. There is a one-year limited warranty on the Clean & Clear Cartridge Filter.
I have a 29,100 gallon pool, should I go with the 150 or 200 sq ft cartridge filter? Thanx
Hi Steve, If your pocket book can handle it I would always suggest going larger on the filter as the filter will have more cleaning capacity and there will be longer time between cleaning the cartridge.
I AM PLANNING TO PURCHASE THE LARGEST AVAILABLE PENTAIR CC FILTER. I WAS OFFERED A 320 SQFT UNIT SINCE I HAVE A POOL WITH ABOUT 42,000 GALLONS. DOES SUCH A UNIT EXIST OR CAN YOU GET IT?. OTHERWISE WE STAY WITH THE 200 SQFT UNIT. IT SHOULD BE SUFFICIENT??
Hans - The CC200 can handle 42,000 gallons. There is a Clean and Clear Plus 320. The benefit of the 320 is that it would not have to cleaned out as often.
Does the CC200 Pentair Cartridge Filter come with one cartridge installed? Also, do you have separate in line filters (before pump) with 2 inch connections? REGARDS HANS BAUMANN
Hello Hans - The CC200 does come with a cartridge. We do not have an inline (pre pump) filter with 2" connections
Does this come with the filter cartridge and gauges?
This filter comes direct from the manufacturer and includes the cartridge and gauges.