Part # 5250-102
Manufacturer Code PSR 201
Dimensions 0.83" X 1.49"
Alternate Part #'s 01512-30, 0151230, 071728, 10139004, 15693, 31812, 320119, 344001, 354231021, 37407-0009, 37407-0019, 374070009, 374070019, 3740719, 3859200, 395005, 71728, as201, P28300, PG-201, PG201, PS201, psr201, PUR1013430, VG-201, VG201
This is a generic replacement pump motor shaft seal that is used on a number of different spa and pool pumps. Some brands and models include the American Products Americana, Sta-Rite Dura-Glas II and Max-E-Glas II, Jacuzzi Magnum, Pentair / Pac fab Hydropump, and Astral 2000 as well as many others. A complete list of pumps that use the PS201 seal can be found under the "Parts" tab above.
I have a A.O Smith replacement - Century pump 1081/1563.... Part 7-184821-04 Need to replace the shaft seal... What part number is this? thanks,
Hello Deryk, the part 7-184821-04 cross-references to 3 HP 2 Speed 230V Low Amps Thru Bolt Motor (3421821) - BN62. If you need shaft seal, we would need to know the pump model number in order to assist you with finding your correct seals.
How do I install PSR Seal for pool pump motor?
Hi, Lonnie. You can use our How To Replace a Pool Motor Shaft Seal guide for installation steps.
I have an AO Smith UST1072. I bought a PS-201 seal that doesn't fit the shaft. The original seal on the shaft had notches for two metal pieces extruding from the bottom of the shaft. Is the PSR-201 the correct seal for this shaft instead?
Hi, Tony. You will need to remove that metal piece in order to get the new pump seal to fit onto the impeller shaft.
I have a Hayward pump model SP3110X152GH, had the seal replaced a year ago. they installed PSR Seal 201V... it lasted less than a year, the rubber split that's part of the compression spring.. this is the second time, Is leslies pool using the correct seal?? Fred
Hi, Fred. The Hayward SP3110X152GH pump uses a PSR-201 Pump Seal.
have ust 1152 pump motor need ceramic seal pump seal 201 will that work on mine
Bruce, The shaft seal is dependent on the pump housing not the motor. Please provide the make and model of the pool pump.
I have a A.O. Smith 1.0 spl pump part#7-187610-21 what shaft seal di need?
Hello Mike, We would need a pump model number to cross reference what type of pump seal you would need.
Does it met for ITT Marlow pump SDA75?
The number you provided does not allow me to pull anything up. If you are looking to replace the shaft seal on your pump please attach a picture of your pump so I can identify what you have.
will this fit the shaft for the ao smith catb227 threaded shaft I am replacing on a argonaut pump?
Yes, that would be the correct shaft seal for your Argonaut.
The shaft is leaking on my above ground pump. The parts tag on the pump shows the following: A.O. Smith HP: 1.0 SPL part # 7-187609-21, serial number BW6-22, SP W48Y. 60HZ, RPM 3450. The wet end has the following tag: Jacuzzi model S1kG9-3, order no. 94027976NB0X, Date 15 Jun 01. I did not install the pool so I do not have any information about it. What shaft seal part should I purchase?
Hi, The Jacuzzi S1KG9-3 uses a Pump Seal 200 (PSR200).
How to get pump separated from motor, I have a motor model s48874a03 and pump model jwpas5f-2a4
While this video and instructions are not for your exact pump, it still covers all the steps needed to remove a motor. Please click "How to Replace the Motor on Your Pool Pump"
I bought this along with a motor. I have setup watching your diff videos. It is a JWPA Sta-Rite pump. After hooking everything up and turning it on, there is water coming from the backside of the impeller so the seal is failing. I did have a VERY hard time getting the seal onto the impeller and I'm not sure the spring is actually able to move properly. Should I lubricate the impeller to help slide on the seal, and if so, with what (not the seal itself, but the impeller to help slide on).
Brian, Lubricating the shaft/inside of the impeller with a silicone lubricant where the shaft seal goes will make it easier to install the seal. You may need to install a new shaft seal since its leaking.
IIs this the correct seal for purex aquatron pump?
Hi Fred, No this not the correct seal for the Purex Aquatron Pump, you would need this Purex Aquatron Pump Seal.
Which side goes where when I replace this 201 shaft seal?
When replacing this 201 shaft seal as well as others you need to put the spring side on or against the impeller with the dark ceramic side out and then the other half of the seal inside the pump seal plate with the white ceramic side facing out. Please be advised not to touch, wet, or dirty any of the ceramic parts for it very well may compromise the seal.
(5 out of 5 stars) Just the part I needed to stop the leak!
Reviewed By: CJsGirl from Galesburg, IL ()
Pros: Super fast shipping and lowest prices
I replaced this seal on my pump last week and it stopped the slow drip leak problem I was having. Inyo shipped it out to me very quickly and I had it on my doorstep within 3 days and at a great price too (along with free shipping)! Will definately buy parts from them again.
(4 out of 5 stars) Affordable Sealing Solution
Reviewed By: Eric B. from Hamilton, MS ()
Cons: Rotating Element Material
This mechanical seal is not bad for the price, but working in the pump and valve industry myself, i would recomend a better face material for the rotating element other than the phenolic face, such as tungtson carbide. The staionary element (ceramic) is fine, as long as you do not experience extreme temperature changes, this will result in cracking the seal face.
(5 out of 5 stars) Replacing seals is a NO-BRAINER
Reviewed By: John M. from Rosemount, MN ()
I am a penny pincher, I could not find a better price than right here at inyopools.com I am very happy I replaced the seals while I had the motor apart. I didn't realize how badly work my old seals were until I had new ones to compare with. I also replaced the impeller which I think really helped circulation. I had more water pressure with a new, lower HP motor, than with the old higher HP motor probably partly due to the new impeller.