Part # GOKIT2
Alternate Part #'s 65002, GO KIT 2, PL1002
Standard tune up kit for the Hayward Super II pump includes the shaft seal and all o-rings, gaskets and lubricant.
We highly recommend replacing the shaft seal, o-rings and gaskets when replacing your motor. If you use your old shaft seal, it will not mate up properly with the new motor and may leak.
This Tune Up Kit Works on These Pumps:
Tune Up Kit Includes:
For more Pool Pump Motors
Click here for Saltwater Pool Tune Up Kit (GOKIT2SALT)
I am buying a UST1152 motor, will this kit fit this motor?
Reply
So the tune-up kits are actually based on the model name or number of the front pump housing that the motor attaches to. If you do not have that information you are more than welcome to send in some images of that to upload@inyopools.com so a tech can review and further advise.
Reply
the shaft seal kit # SPX1600TRA the kit for hayward super pump model SP2610X15
Reply
The seal kit for the Hayward Super Pump on a chlorine pool is the GOKIT3 and the seal kit for a saltwater swimming pool is the GOKIT3SALT.
Reply
I bought a motor-UTS1102 to replace a bad one.Discovered the whole pump was bad so I purchased a whole motor/pump assembly Now the new motor had a terrible winding sound and was very loud so I switched the motors, What is the proper GoKit for Pump Pureline Pl2601? I have concerns that the motor operated only less than a partial season and less than a year. There is extensive white powder around the top of the motor where it was attached to the pump What steps do I take for the 2nd motor issue?
Reply
Hi, Thomas. The Prime Pump does not have a tune up kit, the seals will have to be purchased individually. The Pump Shaft Seal - PL2655, Diffuser Gasket - PL2653, Housing Gasket - PL2656 and or Lid Gasket - PL2649. Using a Motor Cover - R221016 can add some protection for the motor, however, keeping an eye on the pump for leaks and resolving the issue will prevent motor and equipment failures.
Reply
What go kit gaskets for a Hayward RS 1000 pump with a salt pool??
Reply
Hi, Dean. The Saltwater Tune Up Kit Hayward Super II - GOKIT2SALT is the recommended kit.
Reply
Which is the tune-up kit for a SP3010X15AZ Hayward pool pump. Thank you.
Reply
Hi, Keith. This Hayward Super II Tune Up Kit - GOKIT2 or GOKIT2SALT will work with your model pump.
Reply
Is this kit oem Hayward or is it generic?
Reply
Hi. This is a generic kit. The OEM Kit is Part # SPX3000TRA which does not include the Cover O-ring - SPX3000S.
Reply
How do I determine if I have a Hayward Super Pump or a Hayward Super II pump? Do they look the same? Pool was installed in year 2000.
Reply
is the go kit2 good for hayward rs1500 poolpump? A O Smith motor model no. k48m2n110
Reply
which tune-up kit do i need for motor #C48AA35A01
Reply
The seal kits are actually based on the model name or number of the front pump housing that the motor bolts to. You can provide that information to us or if it is no longer legible then you can email us images of it to upload@inyopools.com so we can locate that kit for you.
Reply
which tune up kit do i need for a model UST1102
Reply
These seal kits are actually based on the model name or number of the front pump housing that the motors bolt to. You can call in with that information or if it is no longer legible then you can always email us some images of the housing to upload@inyopools.com so we can confirm that kit needed for you.
Reply
If I replace a 1 H.P. motor withh a 1.5 H.P. motor is there any advantage in doing so ?
Reply
There could be but not necessarily always. If you have or are adding more features to your swimming pool and extra flow is needed then yes. For example, waterfalls, solar heating and deck jets. Or even if the pump was not properly sized per your pool needs upon being built then it possible that it would aid. But if not and the filter is not designed for extra water pressure/flow then it can actually do harm to the motor and or filter.
Reply
hello,
looking for tune up kit for a Hayward SP 1085
Reply
Good morning Aldo, The number you gave me is referencing a skimmer. I would need either a part number off of the pump or a picture to get you the correct seal kit.
Reply
I have a Hayward filter SP3015X20AZ. Is the repair kit GOKIT2 the right one for this filter?
Reply
Good morning Joe, Yes the Gokit2 is the correct replacement for you pump unless you have a salt pool then you would need the GOKIT2SALT. The only difference in the two is the shaft seals are different. The salt one is made out of stainless steel to hold up to to the high corrosion.
Reply
pump motor humms but doesn't run
Reply
Hi, The motor capacitor could be bad or the motor could be dead. You can use out Pool Motor Troubleshooting blog to diagnose the issue.
Reply
Have model motor c48k2db11a9 says AO smith epc. Hayward encl 3 Ec 1300. Is this the right tune up kit for it?
Reply
Hi Ben, We will need the model of the Hayward pump, not of the motor in order to confirm if this kit will work.
Reply
I have a Hayward pump made by AO Smith with a number that I can not match on any Pump site. The pump is SP 3215Z1BER and Par 7-19633720. !.5 HP Total HP 2.4 powered by AO Smith.
What replace motor should I order or replacement parts for me to repair?
Reply
Hi, The motor model number you provided cross references to the Hayward TriStar 1-1/2 Hp Full Rate Motor (SPX3215Z1BER) which is used on the Hayward TriStar pump. You can locate the replacement parts via the Hayward TriStar Parts page.
Reply
looking for a 3.0 hp full rated motor for a super 2 pump model sp3015eeaz. I currently have a a.o.smith 1 1/2 hp with a sf = 1.33, C type, round flange, 56J.
I want to end up with an additional 1 hp when I make the change.
Not enough power currently to efficiently operate both the pop-ups and the jets at the same time.
Reply
Hi Anthony, If you want to upgrade to 3 HP then you would require the 3 HP Super II Replacement Motor, you would also need to upgrade your Impeller to the 3 HP Hayward Super II Impeller and you would need a Hayward Super II Seal Kit. We also have a complete pump called the PureLine Prime 3 HP which would be about the same price as replacing these parts. A few things to consider when going up in HP... what is the flow rating of your filter? You want to make sure that your filter can handle the increased output of the larger pump. What is your plumbing size? You want to make sure that you have at least 2" plumbing and ideally 2.5" or even 3" plumbing, this larger plumbing does a better job with the higher flow of water.
Reply
what is the tune up kit for A.O. Smith PS1615Z2MSC?
i ordered the B2977 from you
Thanks
Reply
The gasket kit is matched to the pump housing and not the motor. What is the model number of your pump housing? If it is a Hayward, the model number should begin with an 'SP.'
Reply
Would this kit work when replacing Leslie's Hydromax II pump motor with AO Smith motor your part # 5222AX. Thanks!
Reply
Hi, The Hayward Super II Tune Up Kit (GOKIT2) will also work with the Leslie's Hydromax II pump.
Reply
Will this fit on a C48L2N134B3
Reply
These kits are based off of the model of the front pump housing that the motor is mounted to. If you have the Hayward Super 2 then yes this is the correct kit.
Reply
Hi,
I'm working on a Hayward RS-1000 Pump (married to an A.O. Smith K48L2N104 Motor). I'm guessing that a CT1102 motor would be the replacement for my old motor. Would this tune-out kit be appropriate for the RS series pump?
Reply
Hi Charlie, The CT1102 Motor will be the correct replacement for old K48L2N104 motor and the Hayward Super II Tune Up Kit (GOKIT2) will also be the correct kit for the Hayward RS1000 pump.
Reply
I need a tune up kit for a Hayward Super II Pool Pump (2004-2005)
Model #K48N2N104. Which kit do you recommend? 2 HP Pump/230 V.
The kits that I am seeing on your website don't match the model number that is on my Hayward Pump.
Thanks
Ralph
Reply
Hi Ralph you would require the Hayward Super II Tune Up Kit here.
Reply
GO KIT2 65002. IS THIS THE KIT FOR UST 1102 REPLACEMENT MOTOR?
Reply
To determine which Tune Up Kit you require we would need to know the model of your pump. Examples would be the Hayward Super Pump, Hayward Super II, Hayward Max Flo, Jacuzzi Magnum, etc.. Please email us back with this information and we will let you know which Tune Up Kit is right for you.
Reply
My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
Reply
The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
Reply
I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!
Reply
You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.
Reply
Less than 1 hr
Socket Set, Wrench Set, Adjustable Wrench
1 0
Purchased Tune up kit and then followed the video online. Watched video through twice before tackling the pump. Took my time, followed instructions, and was fairly simple process. Pump one again running smoothly and we have no more leak! Strongly recommend the Inyopools products and online support information.
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set
1 0
Less than 1 hr
Socket Set, Wrench Set
1 0
I pulled the the pump assembly apart. I figured it would be best to order the pump parts as well as the motor.
The motor and seal/gasket kit came in 3 days. That was unexpected, but was delighted that it came in so soon.
1 to 2 hrs
Screwdriver, Nut Drivers, Socket Set, Wrench Set, Strap wrench, needle-nose pliers
The Most Helpful Review
1 0
(5 out of 5 stars) everything I needed in one small package- perfect
Reviewed By: ()
this is everything you need to replace all seals on a Hayward super II pump- the one with the spin off top....... I used this kit to reassemble the pump when I replaced the motor (leaking between pump and motor). This is an all inclusive kit that puts everything you need in one convenient package, everything fit and was very easy to change using the instructions and videos found on this site. only one word of caution because it can't be stated enough: make sure power is off at the breaker before starting.
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Works great.
Reviewed By: ()
Great product. Easy to install.
Was this review helpful to you?
(5 out of 5 stars) Great!
Reviewed By: ()
Great! Just the right parts and fast too.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: ()
easy to install and no leaks or issues so far.
Was this review helpful to you?
(5 out of 5 stars) THANK YOU!!!
Reviewed By: ()
Perfect for the motor I ordered. Customer service was accurate and helpful to me as I have limited knowledge in this area. Great service and product. Thanks so much for helping me out. Accurate delivery time too.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: ()
Worked perfectly.
Was this review helpful to you?
(5 out of 5 stars) Perfect fit
Reviewed By: ()
Replaced my motor (always use a new go kit!) Perfect fit. Quick free delivery.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: ()
Great !
Was this review helpful to you?