Tune Up Kit Hayward Super Pump - GOKIT3

$37.95

IN STOCK
FREE SHIPPING

Part # GOKIT3

By Aladdin

  4.76 Average  

Details

Top

Part # GOKIT3

Alternate Part #'s 65003, GO KIT 3

Product Description

Standard tune up kit for the Hayward Super Pump includes the shaft seal and all o-rings, gaskets and lubricant.

We highly recommend replacing the shaft seal, o-rings and gaskets when replacing your motor.  If you use your old shaft seal, it will not mate up properly with the new motor and may leak.

This Tune Up Kit Works on These Pumps:

  • All Hayward Super Pumps 1/2 HP - 3 HP single and dual speed models.
  • All Hayward SP2600 Series Pumps
  • Works on both standard efficiency and energy efficient Hayward Super pumps
  • Note: Hayward Super II Pumps use GOKIT2

Tune Up Kit Includes:

  • Motor Shaft Seal
  • Diffuser Gasket
  • Pump Lid O-Ring
  • Housing Gasket
  • Lubricant

For more Pool Pump Motors

Click here for Saltwater Pool Tune Up Kit (GOKIT3SALT)

Top

?     Asked on 9/12/2017 by Brian M

I am swapping a 1HP Hayward super pump motor for a variable speed ECM16CU. Do I need to change the impeller to a 1.5 HP or swap any other parts before I install?

A     Answered on 9/12/2017 by InyoPools Product Specialist Lennox H.

Hi, Brian M. You do not need to change the impeller, you can reuse your 1HP impeller. 

?     Asked on 9/3/2017 by

Will this kit work for a Hayward pump model SP2607X10?

A     Answered on 9/5/2017 by InyoPools Product Specialist Lennox H.

Hi. Yes, this Super Pump Tune Up Kit is for model # SP2607X10. 

?     Asked on 7/26/2017 by Pawel

Hello I have a sp1607z1m pump would this tune up kit work with my pump???Also do I need anything else besides these seals if I'm replacing the bearings in the pump???

A     Answered on 7/30/2017 by InyoPools Product Specialist Alex V.

Pawel, The seals are based on the pump housing not the motor. We will need to know the pump model number. 

?     Asked on 7/25/2017 by Roger

Will this kit work for the 1 A. O Smith 2 HP motor round flange 56J UST1202

A     Answered on 7/27/2017 by InyoPools Product Specialist Lennox H.

Hi, Roger. This kit will work if you have a Hayward Super Pump housing. 

?     Asked on 7/17/2017 by

can you just by the square gasket that goes under the clear top. it is the big square one

A     Answered on 7/17/2017 by InyoPools Product Specialist Lennox H.

Hi. The Strainer Cover Gasket - SPX1600S is available separately. 

?     Asked on 7/5/2017 by robert colarocco

will this kit work with USQ1102 motor

A     Answered on 7/7/2017 by InyoPools Product Specialist Lennox H.

Robert. This kit will not work with the USQ1102 motor. The Hayward Super Pump uses a 56J Round Flange Motor.

?     Asked on 7/5/2017 by

I have a Hayward Super pump sp1610z1m with ac smith c48l2n134b1 1 1/2 hp. Looking for a shaft seal or kit and slinger.

A     Answered on 7/8/2017 by InyoPools Product Specialist Lennox H.

Hi. This is the correct kit for the Hayward Super Pump, the Water Slinger - SPX0125F is not included. 

?     Asked on 6/26/2017 by

I have an old Super Pump SP-2600-Z-1 that is still running normal but is very loud because of bearing wear. I assume I would need a new motor and GOKIT3 tuneup kit? I am not sure what HP the motor is but have a 18'X36" inground pool and want the same size motor. Will a new motor mount onto the existing motor mounting plate?

A     Answered on 7/22/2017 by InyoPools Product Specialist Alex V.

Hello, In order for us to assist, we will need to know the model number on the pump housing. Please contact us with that information. 

?     Asked on 6/14/2017 by Ken

I have a hayward superpump. Model c48k2n143b1. What go kit should i use go kit 3?

A     Answered on 6/14/2017 by InyoPools Product Specialist Joe S.

Good afternoon, if you have the Hayward Super Pump. Then yes the GOKIT3 would be needed for a chlorine pool. If you have salt then it would be a GOKIT3SALT.

?     Asked on 6/13/2017 by Steve

I have the Hayward Pump SP2610X152S attached to a AC Smith SP1610Z2MSC motor; fram X56J; HP 1.5-.25; RPM 3450/1725 (it's a high low speed motor); problem is it runs and sounds fine on High speed, however it has a loud whine/screech on Low speed. Question is: is this an impeller bearing issue or motor issue? Point me in the right direction for seals and impeller replacements please.

A     Answered on 6/23/2017 by InyoPools Product Specialist Lennox H.

Hi, Steve. The noise that you're hearing is a bearing issue from within the motor. Replacing the pump seals will not resolve the issue but GOKIT3 is the part number for the seals and SPX2610C is the impeller part number.

?     Asked on 6/8/2017 by

I have a Hayward Super II pump (model #SP3020X25AZ, Max. Rated) which is making a loud bearing type noise. Do you have a tune-up kit that will alleviate this problem?

A     Answered on 6/8/2017 by InyoPools Product Specialist Patrick P.

That squealing noise is due to your bearings going bad. The bearings can be quite difficult to replace, so we would suggest the UST1252 2.5 HP Replacement Motor along with the Hayward Super II Seal Kit.

?     Asked on 6/7/2017 by Don

I just opened the pool for the season. I have a Hayward super pump. It's 25 plus years old and I cannot identify the p/n or s/n. I do have air from the jets and it is barely drawing in water to the pump. I did have the air last season. Can you assist me at all.

A     Answered on 6/11/2017 by InyoPools Product Specialist Lennox H.

Hi, Don. If your pump is the Hayward Super Pump then I would start out with getting this kit and reviewing the How to Identify and Correct Air Leaks guide.

?     Asked on 6/4/2017 by brian

Will this same shaft seal for the hayward super pump work with the AO Smith replacement motor or does it take a different one? Thanks!

A     Answered on 6/6/2017 by InyoPools Product Specialist Lennox H.

Hi, Brian. This is the correct kit for the Hayward Super Pump which has the pump seal that will allow the A.O. Smith motor to work.

?     Asked on 6/4/2017 by kevin e elbrink

would it benefit me to increase HP of motor say from 1 HP to 11/2 Hp when changing motors.

A     Answered on 6/9/2017 by InyoPools Product Specialist Patrick P.

If you have been happy with your flow then we would suggest staying with 1 HP as it will cost less to operate. If you flow seems to be too low then you could upgrade to 1.5 HP but you will also need to replace your 1 HP impeller with a 1.5 HP impeller.

?     Asked on 6/1/2017 by

where do you ship from? Estimated ground time for a motor to 40324? Thanks

A     Answered on 6/2/2017 by InyoPools Product Specialist Patrick P.

3-4 business days is the estimated delivery time. We have several warehouses we ship from throughout the country.

?     Asked on 6/1/2017 by brian

Hi, I have a Hayward Super Pump CK8K2N143B1, water level ran low due to a busted pvc pipe, pump was still barely pumping when I found it. now motor just hums, replaced the capacitor and still just motor hum. Recommendations? motor and replace seals? if so GOKIT3? and which motor. Thanks! Brian

A     Answered on 6/1/2017 by InyoPools Product Specialist Hector F.

I believe that you meant to type a 4 in the place of the first k and if so the motor replacement is a UST1102 and the gokit3 is the correct seal kit. Also if you have a salt water pool then the gokit3salt would be best for you.

?     Asked on 5/31/2017 by

what tune up kit do I need for 3/4 hp super pump?

A     Answered on 6/1/2017 by InyoPools Product Specialist Lennox H.

Hi. You can use p/n GOKIT3 or GOKIT3SALT.

?     Asked on 5/30/2017 by Jim Smith

Are these seals OK for salt water?

A     Answered on 5/31/2017 by InyoPools Product Specialist Hector F.

Yes they are okay but what would be best and most corrosive resistant to the salt would be the GOKIT3SALT.

?     Asked on 5/14/2017 by Jon

I have a SP2607 superpump and when I turn it on it makes a humming noise and the impeller won't move. But when I take it apart, the impeller moves freely. What do I do

A     Answered on 5/15/2017 by InyoPools Product Specialist Lennox H.

Hi, Jon. It sounds like the motor is the issue, not the pump. You can use the info in our Pool Motor Troubleshooting Blog to determine the cause.

?     Asked on 4/30/2017 by Dennis Morin

i HAVE A HAYWARD MODEL C48K2NI43B1 A.O.SMITM WHICH SEAL KIT DO I NEED FOR THIS MODEL THANKS DENNIS

A     Answered on 4/30/2017 by InyoPools Product Specialist Lennox H.

Hi, Dennis. In order to locate the correct seal kit, we will need the model or name of the pump housing.

?     Asked on 4/27/2017 by

Sucking air from under ground skimmer.What to do? Or who the call

A     Answered on 4/27/2017 by InyoPools Product Specialist Lennox H.

Hi. You will have to locate where the air leak is and repair it. You can call a pool technician or follow the steps in our How To: Identify and Correct Air Leaks.

?     Asked on 4/11/2017 by Bob K

I am replacing a Haywood Super Flow pump motor, It is about 15 yrs old, and I cannot read the model #. (It was there when I bought the house). I am not sure what Haywood O-Ring replacement kit to buy. I would like to stay with Haywood original, but is there an after market that is just as good?

A     Answered on 4/11/2017 by InyoPools Product Specialist Scott W.

For the Hayward Super Pump the correct seal kit is the GOKIT3.

?     Asked on 1/28/2017 by Hayward RS 750 pump seal kit

Hi I have a Hayward RS 750 pump and need to change the seals at is leaking from under the motor housing it has an Emerson tag on the motor housing model # t55cxchl-1324 can you tell me what go kit I would use? The Jim

A     Answered on 1/30/2017 by InyoPools Product Specialist Alan M.

The Tune Up Kit Hayward Super II - GOKIT2 is the correct replacement GOKIT for the Hayward RS Series.

?     Asked on 10/23/2016 by Roger Case

I have a Hayward Super Pump (SP2610x15) and an AO Smith motor (UST1152). What tune up kit do I need. Thank you for your assistance.

A     Answered on 10/24/2016 by InyoPools Product Specialist Alan M.

Hello Roger- The correct tune up kit for the Hayward Super Pump is the Tune Up Kit Hayward Super Pump - GOKIT3 or if you have a saltwater pool, the Saltwater Tune Up Kit Hayward Super Pump - GOKIT3SALT.

?     Asked on 10/6/2016 by Keith

My Hayward RS750CA pump is leaking and water is coming out under the motor. What seals should I buy?

A     Answered on 10/11/2016 by InyoPools Product Specialist Stacey M.

Hello Keith, you can replace all seals with a Tune Up Kit Hayward Super II - GOKIT2

?     Asked on 9/23/2016 by john potts

I have a Hayward Super Pump (Model # C48L2N134B1) 1.5 HP. Won't start and hums, if you tap with a mallet it will start, Replaced capacitor and it still acts the same. Any suggestions? Thanks for any help provided.

A     Answered on 9/23/2016 by InyoPools Product Specialist Alan M.

It is very likely that the bearings on the motor are starting to seize up. You have the option of replacing the bearings or I would recommend that you replace the motor with Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith - UST1152.

?     Asked on 8/28/2016 by Sherry

leak under pump basket? Had a new 1 hp 1081 pool motor installed at least 2-3 years ago and everything ok until this past month keeping a watch on water slowly leaking from under pump basket. Would a tuneup kit take care of this problem? How difficult is installation?

A     Answered on 9/1/2016 by InyoPools Product Specialist Stacey M.

Hello Sherry, is the leak coming from the housing basket area itself or in the middle of housing (where basket is) and the motor? Please just double check your housing to see if there are not any cracks.

?     Asked on 8/15/2016 by Steeve

I have a Hayward RS 1000 pump and a 1 hp motor model UST1102. Which tune up kit will work for my pump?

A     Answered on 8/17/2016 by InyoPools Product Specialist Joe S.

The Tune Up kit you will need for the RS series will be a GOKIT2.

?     Asked on 8/6/2016 by Jim

I have a Hayward RS 2000 pump and a 2 hp motor model K48N2N104. Which tune up kit will work for my pump?

A     Answered on 8/11/2016 by InyoPools Product Specialist Alan M.

Hello, The Tune Up Kit Hayward Super II - GOKIT2 will be the correct seal kit for the Hayward RS 2000 series pump.

?     Asked on 7/15/2016 by bob

Hi, I work at a golf course in cny,taking care of their pools. The wading pool has a hayward SP2605X7, runs memorial day to labor day 24/7. Pump is about 8 years old. The pool is protected with a hayward stratum, so it always has to be startup in the unprotected mode.Slowly getting worse. I`m thinking impellor and the tuneup kit. Correct?

A     Answered on 7/16/2016 by InyoPools Product Specialist Lennox H.

Hi Bob, It's hard to say if replacing the impeller and seals will resolve your issue but it it's worth a shot.

?     Asked on 6/23/2016 by Bill

My Hayward super pump keeps losing the prime on morning startup I'm not losing water from the pool

A     Answered on 6/29/2016 by InyoPools Product Specialist Lennox H.

Hi Bill, You can resolve this issue by replacing the seals within the pump. Also, check the suction side of you pool for leaks. You check out these two How To guides for instructions; How To Determine Why a Pool Pump Won't Prime and How to Identify and Correct Air Leaks.

?     Asked on 6/20/2016 by Ed

I have a sp2605x7 super pump 3/4 hp. I have just started noticing a very little bit of air bubbles in my pool. I changed the gasket for the site glass. Still have air and have noticed a little bit of water dripping under my pump where the pump meets the motor. I will be closing the pool on labor day can I get away with the situation until then or does this need immediate attention.

A     Answered on 6/22/2016 by InyoPools Product Specialist Brian M.

Air would only be getting into the system from the pump housing back to the pool. Best to check the pump lid. 2nd, the small leak is more than likely caused by a faulty shaft seal.

?     Asked on 6/12/2016 by Chad

I have a hayward super pump it won't hold a prime when I put weight on the lid it will run good but if I take weight off it loses prime again will the gasket kit work to fix this problem

A     Answered on 6/13/2016 by InyoPools Product Specialist Alan M.

Yes, I would highly recommend the Tune Up Kit Hayward Super Pump to correct your problem.

?     Asked on 6/6/2016 by ANTHONY DIGRICOLI

Will this tune up kit fit a Hayward Super Pump Modrl # 48L2N134B1, HP 1.5, SP1510Z1M motor?

A     Answered on 6/7/2016 by InyoPools Product Specialist Alan M.

Hello Anthony, this is the correct tune up kit for the Hayward Super Pump.

?     Asked on 5/20/2016 by Jeff

I have a hayward super pump. I bought your shaft seal kit and replaced all seals. The pump is still leaking where the pump meats the mounting plate. What do you suggests? This pump is only two years old.

A     Answered on 5/22/2016 by InyoPools Product Specialist Alex V.

Jeff, It is possible that the housing gasket needs to be replaced. I would also check for cracks on the housing.

?     Asked on 11/29/2015 by Skip

I have two identical Hayward Super Pumps (Model SP2607X10). One needs a new 1hp motor (Model C48K2N143B1). The other leaks water while running, but sounds & performs good. Will the GOKIT3 work for both repairs?

A     Answered on 12/1/2015 by InyoPools Product Specialist Brian M.

Yes, GOKIT3 will work for both, as long as they are Hayward Super Pumps.

?     Asked on 11/26/2015 by Bill

Just purchased and installed Pentair super flo motor and need gokit. What part number do I need?

A     Answered on 11/30/2015 by InyoPools Product Specialist Joe S.

Hello Bill, their is not a GOKIT available for the Pentair SuperFLO. You would need to purchase the parts separate.

?     Asked on 10/18/2015 by

I have a Hayward Super pump model# C48K2N143B1 SP 1607Z1M. When the motor is running water leaks in the bottom between the housing and the motor but no leak when the motor is off. Do you recommend the GOKIT 3 to repair this leak?

A     Answered on 10/20/2015 by InyoPools Product Specialist Hector F.

Assuming that the leak is coming from one of the pump seals or gaskets then yes the kit will solve the issue. However, if the leak is coming from a warped or damaged pump housing part or even a pvc fitting attached to the pump then the kit will not resolve the issue.

?     Asked on 9/30/2015 by Randy Marshall

I have a sp2605x7 pump housing what go kit do I need?

A     Answered on 9/30/2015 by InyoPools Product Specialist Joe S.

Hello Randy yes the GOKIT3 will be the unit needed

?     Asked on 9/23/2015 by jose

My pool pump is leaking and would I like to order a gokit. I have a Hayward Max-flo model SP2807x10. Is the GOKIT3 the right kit? Thanks.

A     Answered on 9/25/2015 by InyoPools Product Specialist Robert M.

Hello Jose - The GOKIT3 is not the correct kit. The correct kit for the Max-Flo is GOKIT1.

?     Asked on 9/22/2015 by Brian

I have an A.O. Smith Round Flange 3\4 HP Up Rate Motor (UST1072) that I purchased from Inyo last year. Which tune up kit do I need to order? Thank you.

A     Answered on 9/25/2015 by InyoPools Product Specialist Matt S.

To find the correct GOKIT for your pump, we will need the pump's model number. The UST1102 motor can be fitted to dozens of pump housing styles that use various seals. You can find the model information on the pump housing's manufacturer tag.

?     Asked on 9/11/2015 by Tom Brown

Is the GOKIT3 the correct seal kit for a Hayward RS1000 pump?

A     Answered on 9/11/2015 by InyoPools Product Specialist Joe S.

For the RS series you will need a GOKIT or GOKIT2SALT

?     Asked on 7/16/2015 by Jeff

My pump gasket is leaking at the basket and I am looking for the go-kit. The pump is marked simply AO Smith ST1152. Some sites say this replaces certain Hayward SPX pumps. Can you direct me to the correct go kit or gasket? Thank you.

A     Answered on 7/16/2015 by InyoPools Product Specialist Andy O.

Jeff- The ST1152 is the model of your filter. To get you the right tune up kit we would need to know the Model number of the of the Pump itself. On most pump this would be located near the basket.

?     Asked on 7/13/2015 by Fred

I have an older model Hayward C48k2N143b1 and it is leaking. Is model GOKIT3 the correct tune up kit?

A     Answered on 7/13/2015 by InyoPools Product Specialist Dennis R.

Hi Fred. C48k2N143b1 is the part # for your pump's motor which can be used in a variety of pumps. The GOKITS are associated with the pump make and model since the gaskets are generally used in the pump and interface to the motor. If your pump is a Hayward Super Pump, GOKIT3 is the correct repair kit.

?     Asked on 6/17/2015 by Chuck

I have a pool pump motor Hayward Super Pump C48K2N143B3. It is leaking and I wish to order the correct parts so that it won't destroy the motor. Help?

A     Answered on 6/17/2015 by InyoPools Product Specialist Robert M.

Hello Chuck - GOKIT3 is the correct kit for the Super Pump.

?     Asked on 6/16/2015 by Dave

My pump has become very noisy. Will a tuneup kit solve this or do I need to look into replacing impeller?

A     Answered on 6/16/2015 by InyoPools Product Specialist Dennis R.

Dave - A noisy pump is usually a sign that your pump's motor bearings are going. Most pool owners replace the pump's motor at this stage. A tuneup kit will not solve this problem. You could also pull the motor out and check the impeller. If it is damaged, it could be rubbing on the side of the pump housing.

?     Asked on 6/13/2015 by

How do you separate the Hayward pump from the Hayward motor

A     Answered on 6/14/2015 by InyoPools Product Specialist Patrick P.

Our How to Replace a Pool Motor Guide will give you the step by step instructions on how to seperate your motor from the pool pump.

?     Asked on 6/12/2015 by

How to get the pump apart to put seal in it?

A     Answered on 6/12/2015 by InyoPools Product Specialist Lennox H.

Here's Step-by-Step Instructions on How To Replace a Pool Motor Shaft Seal and How To Replace Pool Pump Gaskets.

?     Asked on 6/3/2015 by Eric Magnuson

I have a hayward super pump , 1 HP , Model # CK48K2N143 . What Tune up kit should i use

A     Answered on 6/3/2015 by InyoPools Product Specialist Dennis R.

Eric- GOKIT3 is the correct tune up kit for all Hayward Super Pumps. If you have a salt system, we would recommend the GOKIT3SALT kit which is designed to withstand expose to salt.

?     Asked on 5/31/2015 by

I have an AO Smith pool pump, Serial No. 31410CH, Part No 0-193986-24, Type CX. Is this the correct gasket kit for this pump?

A     Answered on 5/31/2015 by InyoPools Product Specialist Alex V.

Gordon, The GOKIT3 will only work on the Hayward Super Pump. What is the model number of your pump housing?

?     Asked on 5/11/2015 by

I have a model C48K2n143B1 SP-1607-Z1-M Which seal kit do I need?

A     Answered on 5/11/2015 by InyoPools Product Specialist Andy O.

The model information you provided (C48K2N143B1), which would be motor UST1102. For the seal kit, we would need to know what the model of the pump.

?     Asked on 5/8/2015 by Rick Willis

Will the GoKit3 work with saltwater pools?

A     Answered on 5/8/2015 by InyoPools Product Specialist Lennox H.

The Tune Up Kit Hayward Super Pump for saltwater pool is GOKIT3SALT.

?     Asked on 5/3/2015 by Terry

Hello does this include the gasket to replace seal between pump housing and filter basket?

A     Answered on 5/3/2015 by InyoPools Product Specialist Joe S.

Yes, this kit includes all seals needed to rebuild your pump

?     Asked on 10/15/2014 by Guest

My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?

A     Answered on 10/15/2014 by InyoPools Product Specialist Patrick P.

The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.

?     Asked on 2/13/2012 by Guest

I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!

A     Answered on 2/13/2012 by InyoPools Product Specialist Patrick P.

You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.

Top
Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver, Pliers, Socket Set, Adjustable Wrench

1     0

Motor went bad

Written on 7/7/2017 by Guest

The instruction on you tube were fantastic. Made the job I was worried about doing it but it was a breeze.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

2 to 4 hrs

Tools Needed

Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Wire stripper/crimper

2     0

My pool pump motor gave up the ghost.

Written on 6/20/2017 by Guest

I purchased the correct motor from INYOU and it arrived days sooner than expected. I took the recommendation and ordered the seal kit as well. Finally on Fathers Day I had the time to tackle this daunting project. Always wary of anything electrical, I took every precaution I could to not electrocute myself with my son present. With everything checked and double checked the moment of truth arrived. I three the breakers on and then threw the switch on the timer box and........SUCCESS! The motor turned and the pump started circulating the water. Awesome feeling of overcoming a fear of electricity and knowing I did it right the first time. The tutorials from INYO were perfect and I saved over $ 330.00 doing it myself.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Socket Set

1     0

seized pump motor

Written on 5/22/2017 by Guest

Removed pump by disconnecting power removing mounting bolts, impella cover and impella. Replaced pump. Tested same before installation and it didn't work. Contacted customer care and they sent me a new one in two days. Installed same after installing new gaskets upplied in the Super Pump tune up kit and new ceramic bearing

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver, Pliers, Socket Set, Wrench Set, Adjustable Wrench

1     0

Motor replacement parts

Written on 5/22/2017 by Guest

Followed these two videos and it was super helpful!
https://www.youtube.com/watch?v=mpJLp3oWDGU&feature=youtu.be
https://www.youtube.com/watch?v=zCNKCYvRSBY

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver

1     0

No

Written on 12/16/2016 by Guest

Was easy to install, would be nice if it included an instruction sheet, but go ahead and check out YouTube and you can find it.

Were these instructions helpful? 
 

Top

Review Summary

  (Average 4.76 out of 5 stars)
151 Rating
5 star:
 
(121)
4 star:
 
(23)
3 star:
 
(7)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews