Part # UST1152
Warranty 1 Year
Dimensions 14" L x 5.5" W x 5.5" D
Alternate Part #'s 168099, 177020, 186922, 54024, 5KCR39SN2823X, 8-168099-20, 8-177020-20, 8-177020-21, 8-177020-23, 90118571, B229, B229SE, C1319, C48L2N131A7, C48L2N134, C48L2N134A3, C48L2N134A4, C48L2N134A5, C48L2N134A9, C48L2N134B1, C48L2N134B3, C48L2N134B4, C48L2N134B5, C48L2N134C1, EB229, JD15FL1, JD15UP1, K48L2N103, sp-1610-z1-m, SP1610Z1M, SPX1610Z1M, UST1152, V54024
Voltage 115/230, Max Amps 115V = 18.6 230V = 9.3, Single Speed, Round Flange, RPM = 3450, Threaded Shaft, Frame = 56J Used on the following models: Hayward Max Flow, Hayward Super Pump, Hayward Super II, Hayward Northstar and Jacuzzi Magnum pumps.
HaywardSP2610X15 pump installed Jul. 2015- 1.5 hp Century motor failed while running No debris in impeller turns freely. Replaced capacitor hums, won't start. Previous motor AO Smith lasted 2 years ( use July - mid Sept 8 hrs./ day on timer) Nameplate : HP 1-1/2 Model C48L2N134 B1 V 115/230 RPM 3450 Fr. 56J SF 1.0 SP1610Z1M Need replacement motor and kit of Shaft seals& gaskets for flange & diffuser Many alternatives on Internet. Need certainty new motor will match
I have a Hayward Super II pump with a Century 2 speed motor rated at 1.5 total hp, SF =1.0 on my part:7-181093-03 X56J frame. What model replacement motor do I need? Thanks Sal
The replacement motor for your model 7-181093-03 is part number 5387X.
Could this motor fit to a HAYWARD POOL PUMP MODEL SP2610x15
Yes, this motor would be a direct replacement for the original model SP2610x15 pool pump.
will this be a replacement for marathon pump 1.5
Hi, Jim. Yes, this can replace a Marathon motor with the following specs 1.5 HP, 56J, SF. 1.1.
currently have a "ust1152" pump with 1.5hp. bearings are going bad. if I wanted to increase hp, what model would I use to upgrade hp? will that increase water flow (as it currently seems weak)and if so will it cause any problems with lines or pol itself???
Hi, Bruce. The next size up will be the UST1202. To achieve an increase in water flow, you will also have to replace the impeller and the diffuser and or other parts depending on the type of pump you have. It can cause filtration and other problems if your system cannot handle the increased water flow. You can use Inyo's How to Size a Pool Pump for Your In-Ground Pool, How To Size a Pool Filter and How To Measure Total Dynamic Head With Gauges guides to assist you in confirming if a 2 hp pump will meet and not exceed your pool needs.
1.5 hp sf 1.0 What impeller do I need? Hayward Superpump with this replacement motor
You would need part number 5110-10DA for this motor in a Hayward Super pump.
Have a Hayward super pump Model c48k2n143b1. Will this motor work as a replacement?
No, actually the correct motor will be the UST1102.
Question asked before, Can this motor be used on a well pump. Thanks. Well pump motor model# C48L2N134C1
We do not actually work with irrigation pump applications but we have learned that many of those pumps do use these types of motors as well.
Hi, Can this motor be used on a well pump.
Hi, Dan. This motor can be used on selected well pumps. Please provide the model of your existing motor for confirmation.
is this motor for inground pools
Hi. Yes, this motor is used with inground pool pumps.
Hi, I have a 1 1/2 HP C48L2N134B1. The pump and motor work fine. But, the motor end cap, to cover the electrical terminations, is rusted out. Can I buy just this cap? Thank you.
Hi, Steve. The End Cap for this motor is not currently available.
I opened my pool and existing pump worked for 2 weeks, then started to constantly trip the breaker. Electrician said electrical sde was OK. I replaced the motor, and it runs for 20 minutes and shuts off....This time the GFI breaker doesn't trip. I can turn it back on after an hour or two, but again it shuts off in around 20 minutes. Is the reason a short in electrical wiring, a wrong setting on pump, a breaker switch? I replaced motor, had electrician and pool guy out and still can't resolve.
Hi, Nathan. The only thing that I can recommend that you check it the pump impeller for ware, damage etc. You can also use the A.O. Smith Troubleshooting for additional troubleshooting tips.
i'm guessing that the Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith - UST1152 is compatible with the Hayward Superpump 1.5 HP motor Model # C48L2N134B1? Thanks Alan
Hello Sir, My pool pump is still working but getting noise when running longer period, (> 0.5 hour). It may need to be replaced, Motor model is C48L2N134B1. The model of C48L2N134C1 you have is matched to my model, and easy to replacement by myself? If I order the motor, do I need other accessories for the installation? your service ship that product to Canada, in Ottawa? Thank you! Shiping
Hi. You will need to replace the pump shaft seal and o-rings along with the motor. We can ship to Canada. Shipping and Duties cost will be additional.
I need to replace my pool pump and want to make sure of which replacement is best. Motor model isiC48AB48A01. There is another label that says MOD # HST150. I can email you pictures if neccesary. Thank you.
Hi, Cesar. This UST1152 motor can be used as a replacement for the HST150 motor.
I have a c48l2n134b3 that needs to be replaced. What do I need and how long to receive the replacement? Zip code is California, 95832
Hi, DJ. This UST1152 motor is the correct replacement. Delivery will be about three business days after it ships which will be the next business day.
I called and was told that UST1152 is the correct replacement for a.o.smith C48L2N134C2- do I need to order anything else in order to replace motor?
Hi, Heidi. You will need a pump shaft seal or tune up kit. You will need to provide the make and model of the pump housing.
Just checked and my current pump is a Hayward SP2610x15 Super Pump with a 1.5 HP motor. The motor says Century Model C48L2n134B1. Need the correct drop in replacement motor.
I need a replacement motor for a Hayward SP2610X15 pump. My current motor is a Hayward and want to make sure I can get a motor than I can replace myself without modification. Is it possible to get by tomorrow?
Hi Larry, This UST1152 replacement motor would be the correct replacement motor for your Hayward SP2610X15 Super Pump. We would also suggest this Hayward Super Pump Tune Up Kit when replacing your motor. If you select the Next Day Air option during checkout and you purchase before 1 PM EST then you would have the motor the next business day.
Do you have a motor to replace US Motors ( Emerson) model: C63MWHPB-5073? tHANKS.
Hi, Thuy. I was unable to locate a replacement in our database for model: C63MWHPB-5073. If you can provide the motor's CAT #, I can use that.
I need to replace UST1152 motor, mod #C48L2N134C1, HAYWARD PUMP SP2610X15. I found the exact replacement on your site, do I need any other parts such as seals or anything?
I have the UST1152 motor (brand new from you) and i believe I need a new pump also. Is there any certain one I would need to match this? Thanks!
Hi. We do not sell pump pumps without motors. You will have to return the motor (if it's in new and unused condition) and purchase a new pump. They're more than 2 dozen different pump that can use this motor.
Where are you located and what are your delivery options to Minneapolis?
HI. Our office is located in FL. Delivery to Minneapolis will be 3 business days after the ship date.
currently have a hayward sp2607x10 with a ao smith c48k2n143b1 which is a 1 hp motor. We think we need a larger motor 1.5. will this fit and work.
Can I use this motor to replace a hayworth motor?
As long as your motor model, part or catalog number matches this one then yes. That information should be right on the motor label itself.
I am replacing a Hayward Super Pump model # C48L2N134B1. Also has the following on it, SP-1610-Z1-M. It is a 1.5 hp. Will this work to replace it and will I need any additional parts? Thanks
I have a Hayward Max-Flo pump model #SP2800ZL with motor model C48L2N134B3.. will this motor work? Any instructions on how to replace the shaft seal and which one I need. The pump model # is not that popular, google's not turning a lot of results when I search it.
Yes, this is the correct replacement motor and if you click here you will be guided to one of our guides for changing a pool motor very similar to yours.
I have a Hayward pool pump with a 1.5 HP motor. Will this fit the Hayward assembly?
If your pump has the model number SP2610X15 or the motor that you are replacing has a service factor(s.f.) of 1 and has been working well then yes this motor would work.
I have a Hayward Super Pump model SP2610X15. The motor (UST1152) is making a lot of noise so I would like to replace it. What else besides the motor will I need?
I have an old pump that is making a LOT of noise when it runs. It is model C48L2N134C1 (UST1152). I would like to replace it. Do I need any additional parts? I have a salt system.
Hi, Larry. You will need this motor UST1152 and the pump shaft seal and or the Tune Up Kit. However, you will need to know the model of your pump housing. You can reference our How To Find The Correct Pool Pump Shaft Seal blog for assistance.
I have this pump and for some reason, water flow stopped going to it. Shouldn't it have cut off before it burnt up the motor? If so, is how do I reset it? Thanks Joe
How To Troubleshoot a Pool Pump Motor - Motor Overheated
will this fit hayward inground pool motor. need replacement for 1.5 hp
We would actually need the motor model, part or catalog number to confirm which motor that you need.
Is there a way for me to send a pic of my pool pump to see if this motor would work? Jack
Hi, Jack. Yes, you can. You can email us at firstname.lastname@example.org.
Replacing 1hp motor ust1102. For Hayward pump SP2007x10. I want to put 1.5hp motor on this pump. Is this a direct fit or are there other parts I will need
Our c48l2n134b1 Hayward motor went out on our pool pump. What is the correct model to replace it with. I can't seem to find that exact number
Yes the UST1152 would be the replacement for the c48l2n134b1 .
I have a Hayward Super II Pump with this motor. It's old and the motor is rusted out...could be 20 years or more! The past week the water flow has been steadily decreasing, and now flow starts out at 50% of what it used to be and drops more and more as it runs. I checked all my lines for air leaks and replaced the pump gaskets, and no matter what source in and water out valves I switch to it's still very slow. Could the motor old and tired, losing power as it runs and not keeping the RPMS up?
It is possible that the motor is having issues with RPM's but that doesn't happen too often. It is also possible there is a pump priming issue. Please view the results here to view a few how-to guides to try and assist in locating other options as to what may be causing your issue.
Will this motor replace Model C48L2N134B1?
Hi, Glen. Yes, this UST1152 will replace Model C48L2N134B1.
I am replacing C48L2N134B3. Will this work ?
Hi, Mike. Yes, this UST1152 will work as a replacement for C48L2N134B3.
i am replacing an hst 150 is this motor compatable
Hi, Robert. This UST1152 will replace the HST150 motor.
I'm replacing a Hayward 1 HP Super 2 pump motor with a 1.5 HP Century Electric. What impeller and diffuser would I need to use? Will the Hayward brand for a 1.5 HP Super 2 work for the 1.5 HP Century Electric?
I have a C48L2N134B1 that no longer works and I need to replace. Will this motor work? What will I need to replace? Thank you.
Hi, Tom. Yes, this UST1152 will work as a replacement. You will also need to replace the pump shaft seal. I will need to know the model of the pump housing.
Is the 5kcr39sn2823ax the same as 5kcr39sn2823x, and is the replacement for 5kcr39sn2823x a good replacement for the 5kcr39sn2823ax?
Hi, Ken. The 5KCR39SN2823AXand 5KCR39SN2823X motors are the same.You can use this Century UST1152 motor as a replacement.
hello, would this be a good replacement for the Regal Beloit EPC, INC HST150 motor? thanks!
Hi, Gary. This Century UST1152 motor is a replacement for the HST150 motor.
will this motor be an exact fit for a sp161ozmsc type cxpm serial # 280113m
Hi, Ruf. Yes, this UST1152 motor can be used as a replacement for the SP1610Z1MSC motor.
I just bought the above motor and I am trying to figure out what side is the top so that I can properly attach the mounting plate and seal plate?
Hello- The vents on motors will always face down.
Do yo have replacement seals formodel c48l2n134b1
Tom, Based on the model number, the replacement is the UST1152.
Does this replace a Hayward (C48L2N134B1) serial # 0L04. SP-1610-Z1
Yes, this is the replacement motor for your model motor.
The line supplying my in-ground pool equipment was permanently tripped. Forcing the breaker in place, the pump motor buzzes but doesn't come on. The pump is Hayward 1.5hp super pump, with a Century motor c48l2n134b1. Should I just replace the motor or the whole pump? (it is only 2 years old). If the motor - the model you have is black, but my motor is gold. Also, your model # doesn't have a "b1" at the end. Thanks
Igor, If the housing is still in good shape, you can replace the motor and seals. Century makes the Hayward motor. The gold color is Hayward's trademark color. The replacement motors can not be the same color. The only difference between the 2 motors is the color. The motor model number we have listed, is a partial one. There are many different variations on the model number. You should be able to find your exact model number in the alternate part numbers list.
hi my pool motor pump C55CXKMC-5013 just burn out i wondering if you have the right one to buy thanks
Yes the UST1152 Motor is the proper replacement motor for your C55CXKMC-5013 motor.
is this replace of A.O.Smith 1 Hp (Hayward super pump & self priming ) with model # C48L2N134B4?
Yes, this would be a replacement motor for your model motor.
My Hayward Super Pump model C48L2N134B3 SP-1610-Z1-MBK just died on me due to lack of maintenance by the previous owner. It looks a bit old and I am wondering if this motor would be able to fit where the current motor resides. My internet searches keep coming up with this particular pump and so I am looking into purchasing it as the replacement. Thanks for your help.
Yes, this is the replacement motor for your pump. You may also want to purchase either the standard seal kit GOKIT3 or the salt water seal kit(if you have a saltwater pool) being the GOKIT3SALT. These contain all of the seals and gaskets when changing the motor which is highly advised.
Just bought a new motor. I couldn't get the motor mount plate off the old pump so I bought a new one. I used all other old parts. Put it together. Its leaking. Not between the pump House n motor mount. Looks like between the shaft seal n motor mount. Where do I go wrong?
A number of things may have gone wrong but most often it is due to a seal or gasket being, bad or dirty. Sometimes it is the condition of them over time and other times one could have somehow gotten compromised during installation. We would recommend inspecting all seals and gaskets. Inspect the housings and parts and go back over installation process.
I'm replacing a Hayward 1HP pump. Is it ok to upgrade to this pump? Will it make much difference?
Hi, Jamie. If your goal is to increase the water flow you'll need to replace the impeller of the pump. If you do not change the impeller and increase the motor the water flow will not increase. It will only make a difference if you change the pump's impeller.
I bought the 1hp version of this motor from you last year and now it stops running and is super hot in under 30 mins. Would the 1.5 hp version run better? The 1hp version even when new would always shut off constantly on hot days. Never had this issue with any previous pumps that were installed. 1 lasted 7 years.
Hi Joe, you wouldn't happen to have the motor information from the motor you replaced? By chance you could have replaced a 1 HP full rate motor with a 1 HP uprate motor which would have overworked the new motor. I would suggest going with the 1.5 HP replacement as the motor will be under less stress and should last longer.
Can the GOKIT3SALT tuneup kit be used on the Heyward Super Pump WITHOUT the chlorine generator when one is adding salt to his pool water but has not installed a salt/chlorine generator?
Hi, King. The Super Pump Saltwater Tune Kit can be used with a chlorine pool that is not yet converted.
hi quick question is it normal to have a century C48L2N134 on a brand new Hayward max Flo
Yes it is but technically you cannot get the original 1st generation Max Flo any longer.
I have a motor to replace on my pool. Info on it is: hp 1.5 SPL 70 GPM ,hayward Flo lx, series OK05, type SP amps 12.0, SP1515-Z-1-BC, FR T48Y. Is this what I need to replace it? Thanks
I have a c48L2n134B1 ( -SP1610Z1-M). Which is the correct motor replacement and do I need anything else?
Hi, Joe. This Century UST1152 Motor is the correct replacement for MOD C48L2N134B1. You will also need the Pump Seal - SPX1600Z2.
Will this replace my Haywood Super pump 1-1/2 hp motor? SPX1610Z1M
The pump is leaking. There is a rubber band type seal between the motor and pump housing. It's difficult to get seated properly and water started coming out down below. After talking with a friend in the business we followed his suggestion of applying silicone and it still leaks. The spring loaded ceramic seal provided for the original inner seal but wouldn't fit due to the i.d. of the metal ring. We used the original spring loaded ceramic seal (it has no metal ring). Suggestions? Thanks.
I would recommend replacing all of the seals and gaskets and inspect the pump parts for any damage such as cracks or warping. In order to cross reference the correct seal kit for your pump you will need the front pump housing model name or number that the motor bolts to. If you cannot locate that information then you can send a few images of that housing to our support request page.
is this the correct replacement for hayward #SP2610X15
Yes this is the proper replacement motor for a Hayward 1.5 HP Super Pump SP2610X15. We would also suggest a Hayward Super Pump Seal Kit when replacing your motor.
Is this motor interchangeable with an AO Smith K48M2N110
No this motor is not a replacement for your K48M2N110 motor, you would require the ST1152 1-1/2 HP Full Rate Motor which would be a replacement for your motor.
Can you tell me which motor will replace the AOL Smith SP3210z1m?. Thanks
Hi, John. This Century UST1152 motor is not the correct replacement, the correct replacement motor is p/n SPX3210Z1MR.
will this unit be a good replacement for a hayware c48k2n143b1 thanks
No, the correct motor replacement would be the UST1102.
I have a Hayward Flo Max 2 1.5 horse pump with an AO Smith motor C48D43A04. I just ordered the replacement motor by Century from your site. I read that I need a gasket kit. Please advise as to part number. Thank you.
I believe that you are referring to the Max Flo II. There is no actual seal kit for this model so I would recommend replacing at least key numbers 8, 11, and 12 on the parts diagram here.
Pump motor A.O. Smith model # C48L2N134 serial 8L96 hums and the shaft is bound. I figured I would change the motor while I have to change the shaft seal. Is this a good replacement part / motor?
Hi, Mike. This Century UST1152 motor is a good replacement for the C48L2N134 motor.
what would be the best motor to use . my motor HST150 CET40ABM. MOTOR MOD C48AB48A01. (TYPE C REGAL BELOIT EPC,INC) I'M JUST NOT SURE WHAT MOTOR TO USE THEREIS SO MANY. THERE IS A STICKER ON IT THAT SAYS.. ST1102-1HPX1.5SF =1.5THP AND THEN UST1152 -1.5HPX1.0SF=1.5 THP. I HOPE THAT HELPS YOU. MINE SAYS THE MAX LOAD AMPS 17.2/8.6. BUT EVERYTHING ELSE IS THE SAME THAT IT SAYS ON YOUR 'S
You could replace your motor with either St1102 or UST1152. If you have your pump model I can help you with the correct shaft seal you will need for the motor install as well.
My old motor is a C48AB48A01 that is the motor mod. will this one work with in place of mine.
Hi, Terry. I was not able to cross reference the MOD # C48AB48A01 to a specific motor. Please provide the HP, SF, FR and Type from off of the motor label or a photo of the motor label and housing so that I can locate the correct replacement.
I have a 1.5 hp Hayward pump C48L2N134B1 Does this replace that? Thank You, Mike
Hi, Michael. Yes, the UST1152 is the correct replacement for the C48L2N134B1 motor.
What's the difference between the C48l2N134B1 and the C48l2N134B3. Will this replace the B3 also?
Hi, Mike. There is no difference between the two model numbers. The UST11052 motor can be used as a replacement for both numbers.
i have an AO Smith C48l2N134B1 motor for my pool pump, can you tell me the exact replacement I would need to order
Hi Steve, the UST1152 would be the direct replacement for your C48l2N134B1 motor.
Where I find a house for ray vac in ground pool vacuum
Hello, I apologize but can you please clarify what you are asking?
I have a Hayward Super II Pump and I need to replace the electric motor. My motor is A.O. Smith Model K48L2N104, S/N 8B07,115/230V 60Hz, 1 HP, 3450 RPM, FR 56J, Hayward # SP-1610-Z-1. I would like to upgrade to a 1.5 HP and get a new slinger and all of the seals. What is the cost? How fast can you ship it to me? Thank you,
Hi, Bill. Based on the info provided the pump you have has a total hp of 1.5 due to the service factor of the motor. So you would not need to upgrade to a 1.5 hp motor. The next size up would be a 2 hp which would be the B796 Full Rate Motor. You would also need the following parts SPX3015C, SPX3005R and GOKIT2/GOKIT2SALT.
I have a replacement motor that I believe the bearings are going out on. Its a US Motors, Model # K63CXDGJ-5170 1.5 HP, 230/115 Volts. Is this the correct replacement for that? Also, do you sell motor parts? I had a screw break on the front end bell so I wasn't sure if you sold those as well as the actual bearings. Thanks,
Hi, Geoff. The Century 1.5HP 56J Full Rate EE Motor - B796 would be the correct replacement motor. We do not sell replacement parts for US Motors.
Is this pump compatible with a Motor Model C48L2N134C2 (Original Motor was A.O. SMITH MOTOR)? Is this pump really a 1.5 HP pump (continuous run at 1.5 HP) or a 1 HP pump with a SF of 1.5?
Hello Ben- According to the part number you provided C48L2N134C2 your motor should be a 1 hp with a 1.5 S.F A.O. Smith 1 HP Full Rate Round Flange Motor - ST1102, but you can use the Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith UST1152 as well. They have the same Total HP.
How do I determine the age of a motor/pump? From the plate, I see RS 1500 Hayward A.O. Smith > Model K48M2N110 > SER 8G04
Hello- According to Century's motor date code explanation, it would appear that your motor is from 2004. For the age of the pump you would have to call the manufacturer Hayward with your serial number.
Please tell me if a motor with model number C48L2N134B3 is the same as a UST1152. Thank you.
Yes that is the correct replacement motor.
could you tell me what the max pump flow is on this motor? CA48L2N134B1
These flow rates are not dependant on the motor models alone but the pump housing models as well. Please call in and provide that information or submit that information here. Also it looks as if the actual motor model number is C48L2N134B1.
I have what seems to be a super II Hayward pump. It looks square and every technician is telling me to get a square flange. However th e frame number on the motor plate is 56J and that is a C face motor plate reads: K48M2N110 SER 8104 HP 1 1/2 KW= 1.1 Volts 115/230 RPM 3450 AMPS 19.4/9.7 HZ 60 SF 1.34 ??(not sure since it is partially scratched) PH 1 Thermally protected CET36WX AMB 50 RU TYPE UAK DUTY COTA?? CODE L Insulation Type B SP-1615-2-1BE
Hello Matt- The correct replacement motor for your Super II motor # K48M2N110 would be the A.O. Smith Round Flange 1 1/2 HP Full Rate Motor (C1101, ST1152). We also recommend getting the Tune Up Kit Hayward Super II - GOKIT2.
Will this motor fit in a Hayward model SP2600VSP (1.5 HP)?
Yes, that is the replacement motor if you are wanting to change from variable speed to single speed. Also, when replacing the motor make sure to replace the shaft seal as well, part number SPX1600Z2.
Hello, I have a Hayward C48L2N134B3 - HP 1.5 - RPM3450 115/230V Do you have an equal to this model?
Yes, the UST1152 is the correct replacement motor. If you have the model of your pump I can help you find the correct shaft seal you will need to complete your motor install.
On the Century UST-1152 (replacing c48L2n134b1 AO Smith) is servicing motor required. Current motor is 2-3 years old and making strange noise. How do you service motor if necessary.
I have a Hayward super pump AO Smith model c48k2n143b1 Is this a good replacement?. I see where this is a 1.5 HP whereas mine is a 1Hp, will that have a negative effect?
Hello Tony- Based off the part number you provided c48k2n143b1, the correct motor for you is the A.O. Smith 1 HP Round Flange Up Rate Motor - UST1102. Using the Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith - UST1152 without changing the impeller or checking if your filter can handle the added flow could damage your filter and/or motor.
I need to make sure this pump is the replacement for my 1.5 hp Hayward super pump C48L2N134B1 before I order it. I had my Hayward super pump freeze up/burn up and I'm just needing a replacement.
I have a Hayward Super 2 pump 1.5Hp Model C48L2N134B3 & need a replacement motor. Is this the correct replacement motor for my pump?
Good morning Kenneth, You are looking for a Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith - UST1152 If you let me know what type of pump this motor is on. I can recommend the correct seal kit you will need.
I have a Hayward super pump that is 20yrs old can't read the model # but the service # is 8197 can you tell me anything about this motor it went out . Want to replace it . I can by a Hayward 2 hp variable for cheap. The pool is 10,000 gal w/2" plumbing and Hayward 3040 filtration will this be to much?
Good afternoon Steve, Here is a link to Hayward super parts.Hayward Super Pump Parts You will be able to find your replacement motor and seals here.
Need a motor for my Jandy stealth JHP-1.5. Round flange. Part number on the motor is AO Smith 7-193633-24. Is this the correct motor?
Good afternoon Charlie, You are looking for part Motor 56j Thrd Full 1.5 Hp (b129) You also will need to replace the shaft seal you can purchase aTune Up Kit Jandy JHP + JHPU Pump Series - GOKIT77 which will have everything you need.
I have a Hayward max flo pump and I plan on replacing the motor with the A.O. Smith motor UST1102. What other parts do I need to buy? O-rings, shaft seal, etc..? Thank you
Hello Marc- Here is a link to the Hayward Max-Flo Parts page for your reference. Anytime you change a motor, we recommend you replace the seals. The Tune Up Kit Hayward MaxFlo - GOKIT1 or the Tune Up Kit Hayward MaxFlo Salt Pools - GOKIT1SALT contain all of the seals you would need to replace for your Max-Flo pump.
I have a hayward model number C48L2N134B1 1 1/2 horse motor. Will this motor work?
Hello Joseph- The Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith - UST1152 would be the correct replacement motor.
What is the difference between a full rated and an up rated motor? Will they work for the same application?
Good evening Ted, The difference between full rated and up rated is the service factor. Up rated motors have a higher service factor giving them a higher total horsepower. Heres a link that will help you understand this How to Replace Full Rated and Up Rated Motors
The motor on my pump is model # C48L2N136 which your search engine says to use a UST1152 replacement. But my motor is a two speed motor and your replacement is only a single speed. How can this be? Shouldn't my replacement motor be a dual speed also?
Good morning Rick, If you need a dual speed pump 1.5hp you are looking for A.O. Smith 1-1/2 HP Round Flange Dual Speed Full Rate Motor (STS1152R)
My pool pump went out...model c48m2n111b4 1.5 hp volts 230 rpm 3450 ser 8b01 amps 10.8 sp-1615-z1-bbk What should I buy from you to replace this motor?
Hi, Billy. Based on the info provided the ST1152 motor is the correct replacement motor you'll need.
HI, I have Hayward super 2 pump (model # sp-1610-z2-mkb) which motor is compatible to this pump if I like to buy just motor (would it fit to rest of my old pump). Thank you very much.
The UST1152 will fit the Super Pump and the Super 2. According to the model # though, that tells me it is a Super Pump not a Super 2. If you want to attach a picture of your complete pump I can make sure we are talking about the correct pump and then I can get you the correct seal kit to go with your motor.
Hello, I bought pool pump UST1152 (A.O. Smith 1.5 HP Round Flange Up Rate Motor - C48L2N134) a little over a year ago from you and it just recently started to make a louder than normal screeching sound. I've been researching and am pretty sure that it's more than likely the bearings. At least, I hope that's the issue. Can you please tell me which replacement bearings I need to order for this motor? I'd really appreciate any information and advice that you can give me. Thanks, Sergio
Good morning Sergio, This is the part you are looking for. Next A.O. Smith Bearing, 203 (62032rs) (Single) A.O. Smith Bearing, 203 (62032rs) (Single) How To Replace the Bearings in a Pool Pump Motor - Part I How To Replace the Bearings in a Pool Pump Motor - Part II Bearing, 203 (62032rs) (Single)
Hi, Wich model do I need to replace my Hayward Super Pool motor, Model is C48L2N134B3.Serial is 03208FM The condenser is Packard PMJ161, 161-193MFD Will the new pump come with the condenser? Do you ship to Canada? Thank you very much.
Hello Martial- The c orrect replacement MOTOR is the Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith - UST1152. The motor will come ready to install including the capacitor. Whenever you replace a motor, we highly recommend you replace the seals. The correct seal kit for the Hayward Super Pump is the Tune Up Kit Hayward Super Pump - GOKIT3.
My motor just fried and stopped working. Wondering if this is the right motor to replace it. Model number is 1203006488 HZ60 Franklin Electric/Jandy Pumps. It says 1081 pool motor. Thank You
Hello Jay, This would be a replacement for the pump HHP FULL RATED & HHPU UP RATED SERIES for Jandy. Please make sure your current specs match up to the one you have currently, HP, SF, AMPS, VOLTS, etc.
Hi, I have a 12 year old pump, Magnum Force Jacuzzi. The motor is a AO Smith 1.5 HP. Here are the numbers listed on the motor. Ao Smith 1-10SF Cat Part 7 -184949 -22 Type: CX ER 56j form: KJM Class : B Code: K Serial: BY 11-24 Is this motor UST 1152 56j the replacement for my motor? I would also need the correct seals.
Hi Jim, Based on the info provided that UST1152 is the correct motor and GOKIT14 will include all the seals for the Jacuzzi Magnum Force pump.
Is this motor 220V or 110. The one i
This motor is both. It will arrive out of the box set to 220v, but it can be adjusted to 110v is desired.
Is the C48L2n134 the replacement for a Hayward Super II Pump motor. On it now is a US Motor EUST1152.
Yes, that is the correct replacement motor for the Super 2 along with part number SPX1600Z2.
Replacing a hayward c48l2n134b1 will this work?
Hello Michael, Yes the ust1152 will replace c48l2n134b1.
Bought century 1.5 HP motor to replace Hayward and when turn on it shuts off . Thinking it may be ser at wrong voltage. How do you switch it? I see a black arrow shows 230 but does not turn easily, is there something special you need to change the dial?
Here's a link to a video from our website that takes you step by step on how to wire a motor.
I am replacing the motor on my Jacuzzi pool pump. The current motor is a c48k2n143c2c. Will this motor work? Thanks!
Hello Mike, for the c48k2n143c2c number you gave it came up with A.O. Smith Round Flange 3/4 HP Full Rate Motor - ST1072. Depending on your housing we would need to see pictures or the model of the pump to give you a seal kit. You can send pictures to email@example.com so we can better assist you.
UST1152 motor, does it come with gaskets and seals for this price?
The only seal that comes with it is the water slinger that is on the shaft of the motor. You would need to get a tune up kit if you wanted to seals and gaskets. It has not come with it because that motor goes to an abundance of different pumps. If you know the model of your pump, not the motor, I can help you identify the correct tune up kit to get.
I have a Hayward Pump model # SPX2810X5. This maybe a Hayward Max Flo? Will this motor be a direct replacement? And what other items I will need to install this. Thanks.
Hello Mer, The UST1152 would be a direct replacement, please make sure to double check specs for frame, HP, and RPM. I would also recommend a Tune Up Kit Hayward MaxFlo - GOKIT1 to replace all orings and pump seal.
Do you know which starter cap I need for this motor? And do you sell them? Thanks!
Hello Mary, Yes we sell Capacitor, MFD 161-193 (BC-161) 110-125VAC for $23.99
I need repair or new irrigation motor. AO Smith, C48c53a06. SER 8c04 PLease Call Larry Ball (803) 646-1127 331 forest pines rd AIken, S.C. 29804P Pump motor is used for in ground sprinklers.
Hello Larry, Please check specs, but the closest I could find for you was UST1152. Please check all specs, amps, frame and is you have cface or square flange.
Hi, I have a 1.5hp Hayward Super II pump. In april it simply hummed but didnt rotate. I opened to see that nothing was blocked, all was free. all of a sudden it ran fine. It has run since April full time not cycling. The only time the pump stops is during cleaning, backflushing, etc. Today I turned it off for backflushing and it has the same humming as in April. Could this be a start capacitor issue? Where is that located in the pump and if yes how do I trounle shoot/replace it? Thanks
That would be the run capacitor, part number 5270-14, which is located under the motor end cap.
I'm replacing my SP2607X10 pump with this pump. First is it the right replacement pump and is it OK to go from a 1HP to 1.5HP?
Hello Fred I would go with ust1102. Check the spec of you motor and compare to the ust1102. Check the frame, volts, RPM, SF, etc.
Can you tell me where I can find a template for the valve positions on the A.O. Smith 1.5 HP Round Flange Up Rate Motor?
Unfortunately a template you are requesting does not exist as motors do not have valve positions. The motor is a part that is attached to the back of your pump. In front of the pump is a valve(s) that control the water drawn from the skimmer, main drain, vacuum port, etc. before it enters the pump. You can always send in pictures to firstname.lastname@example.org of your plumbing setup if you have specific questions. Keep in mind there are multiple different plumbing configurations for pools so photos will assist us in assisting you. Thank you!
need a replacement pump for my Hayward super pump model C48L2N134B1 HP1.5 SER OF06 KW 1.10 RPM 3450 AMPS 18.6/9.3 HZ60 SF 1.0 AMB 50C, ENCL- ODP TYPE-UAC CODE-H INSUL-B SP1610Z1M Will this Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith - UST1152 works or compatible ? your expertise is highly appreciated.thank you
housing seal kits how I get
Hello Melva, we would need to know what brand and model you have, such as Super pump 2600. It is normally located on the side where your basket is.
I need to replace pump motor. I have an AO Smith motor; CAT B129 Serial # 11610CH, FrameP56J, 2.5hp, SF 1.30. I have a Hayward RS1500 pump. What type of motor and kit do I need to purchase. Thanks
can this motor powerful enough to propel a surfboard with a person weighing 120lbs
Could you give me some more details on what you are trying to use this motor for so I can give you a better answer to your question?
I have a Century UST1152 that is 2 years old. The pump is on a timer. 2 days ago the filter did not turn on. It is getting power. Tried turning on and off several times and it finally turned on and ran all day without issue. Today the same thing occurred. Any idea what I should troubleshoot first?
Sounds like your start capacitor has gone out. The part number for that is 5270-14.
I purchase a new Hayward Super pump (1.5 HP) , last year. Just the other day, white wire, burned. I repaired it and now it is running but the case is hot to the touch. I think I need a new one. The first pump I had one prior to the one I have now lasted over 10 years. Any ideas? I don't what to rush you but, if I could get your opinion asap, so I can order if need be. thanks
Bill, Is the motor shutting off? If not, it is likely running under normal operating temperatures. The motors can be very hot to the touch,
I have a pool pump motor AO Smith Model C48L2N134 B1. It overheated and stopped. Is there a reset switch? Or is it dead?
It's most likely dead. Once you overheat something electrical, the damage is usually done.
I'm replacing a Hayward 1-1/2 HP super pump motor. It lasted about 6 yrs. Is this normal life space? Any recommendations on how to prolong this? I've read about having some type of cover over the motor to protect it from elements. Might not do any good, however, as I think salt water from the pool caused the failure. Thanks.
That would be the correct replacement motor. As far as the shaft seal, if you have a saltwater pool you'll definitely want the shaft seal for saltwater pools. It more heavy duty and less corrosive. And we do have a motor cover that does add some protection from the elements.
1.50 hp 3450rpm S.F.1.1 60 hz 1 ph 115/230v 1.1 KW cet50abm maxamp 19.2/9.6 A.O. SMITH EPC MODEL C48L2PA105C3 ELECTRIC MOTOR NEED FOR SPRINKLER SYSTEM HOME
Hi Chinubhai, Based on the info provided the USQ1152 motor is the correct replacement.
am replacing my pool pump motor. Old one is model Hayward Super II pump 1 1/2 HP please tell me correct motor to order.
Hello, The correct replacement motor would be the Century 1.5 HP Round Flange Up Rate Motor (C48L2N134) Formerly A.O. Smith - UST1152. I would also recommend replacing the seals when changing out your motor. Your tune up kit will be the Tune Up Kit Hayward Super II - GOKIT2.
I am replacing my pool pump motor. Old one is Hayward Super II pump 1.5 HP please tell me correct motor to order.
I am replacing my pool pump motor. Old one is model number k48m2n110c1, please tell me correct motor to order.
The correct replacement motor will be the ST1152.
will this fit my current pump, a Hayward Super Pump model C48L2N134B1?
Is this motor tefc or old classified?
Hi Justin, This motor is not TEFC but ODP.
Can I use this motor to replace motor model # K48M2N110 with Impellar P/N SPX3016C? I know it is not the most energy efficient but will this work the same minus the extra cost in electricity ?
I have a Hayward II super pump self priming 1.5 hp, volts 208-230/115, threaded shaft, for my bubbler and rock fountain. The frame is 56J. Will this work?
Hi, Yes, this motor will work if the motor you currently have has a service factor (SF) of 1.0. We will also recommend that you get the Hayward Super II Pump Tune Up Kit (GOKIT2).
shaft dia of a 1.5 hp elec mot
Hi Ray, The threaded part of this motor shaft is 7/16".
Is the pump new or rebuilt?
The motor is brand new in the original manufacturers packaging. It is not rebuilt or refurbished.
What impeller do I use with this motor
The correct impeller is determined by the Pump you have AND the motor you have. I would recommend obtaining the information on which pump you have and we can assist in finding the parts list associated with your pump to locate the correct impeller.
What is the 2 speed version of this? I have a Hayward Super Pump. Also, what is the capacitor for this model ( I'm deciding between a full replacement or just the cap) Thanks
I need to replace a inground pool pump motor AO Smith Model C48L2N134 B1 - Fix me up - D.H.
Yes that would be the correct replacement motor. Did you need help with something else?
Needing a motor for a jacuzzi pump. Present motor is AO Smith part 7-184949-22 type CX. It is a 1'5 hp rating with frame P56j Motor also states it is for 1081pool pump duty. Is this the correct replacement? Thank you
Yes, that would be an acceptable replacement for your jacuzzi pump.
Wiring diagram for low voltage
Hi James, Instruction can be found in our How To: Wire a Pool Pump guide. Which will call for the motor being switch from 230 volt to 115 volt. Then connecting the 115-volt wire to the L1 terminal and the neutral wire to L2 and the green to the ground terminal.
is this motor self priming
Hi, This motor can be used on self-priming pumps but by itself if not considered self-priming. It all depends on the type of pump that this motor is connected too.
does this model motor fit on a hayward super pump model c48L2n134B1
The A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) is compatible with the Hayward Super Pump. I would also recommend replacing your seals with the Go Kit 3 Tune Up Kit for the Hayward Super Pump.
my original pump ( sp2610x15 ) lasted many many years . When it failed I replaced it with a sp2607x10 as advised by my local pool supply store saying the 2610 was wasting my money and electricity with no gain (I think they just sold me what they had I stock) Never was happy with it and has failed at 4 years. If I purchase a motor and impeller for the 2610 will it fit my 2607 housing and it now be a 2610? Did not know about salt seal may explain short life.
my pump is SP3015EEAZ,no markings on the motor,is this correct replacement?
Rafal, If you have the SP3015EEAZ, you will need the ST1152 motor.
I have a hayward super pump with motor number c48l2n134b1. What would the recommended pump and replacement parts be?.
Hi John, The UST1152 motor is the correct replacement for MOD # C48L2N134B1.
I have model # K48M2n110 Hayward self priming super 2 pump. What is the direct replacement motor for this ?
The replacement motor for the model #K48M2n110 is the A.O. Smith Round Flange 1 1/2 HP Full Rate Motor (C1101, ST1152). I wuld also recommend replacing the shaft seal with Tune Up Kit Hayward Super II.
I have a hayward 1 hp pool pump, Only lasted 3 years Mod C48K2N143B1. Would it be beneficial to go to a 1.5 hp.? Same frame 56J.
Hi Joe, If your system can handle the additional water flow of a 1.5 HP then you can replace the UST1102 with the UST1152 motor. You will also need to change the impeller. It might not be beneficial if the 1 hp motor is sufficient for your pool.
Will this bolt up to a pentair 340039?
This motor will not fit the Pentair Pump 340039. I would recommend the 1.5 HP Standard Motor - Full Rate (B2858) as a suitable replacement.
what is the return policy just in case i ordered the wrong item
Hi, Please review the Inyo's Return Policy. If you can provide us with the motor's part, cat or mod # we can locate the correct replacement motor.
Hello, I currently have a SP1607-Z-1-BNS Hayward A.O.Smith Pool Pump. I'm looking to upgrade to a variable speed one to reduce my utility bills, do you have any recommendations or advice on which one I should get? Thanks
Hi Steph, The ECM16CU motor is the recommended vs motor that will replace the SP1607-Z-1-BNS.
Great website! Very informative and helpful. I'm looking to replace my Hayward pump. #C48L2N134C1 1/12 HP. What would be the correct replacement? The one I thought was $148. However, when I tried your shipping charge calculator, it didn't seem to work. Either that or the shipping was included because it kept coming up $0.00. My zip is 16001. Can you give me an idea of the shipping or is it included? Thanks again.
The correct replacement motor is the UST1152 A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134). Shipping on the motor is free. The normal delivery time is three days.
Is this pump compatible to replace from a Hayward Super Pump 1.5 hp ?
Yes this motor replaces the 1.5HP motor on a Hayward Super Pump.
Hi..I am needing to replace Super Pump Motor (UST1102) Model (C48K2N117A9) which is a 1 hp. Wondering if it would be beneficial to purchase a slightly more powerful motor (i.e. 1.5 HP)? Would a more powerful motor damage my filter or other equipment? What would be the benefits (if any)? THANKS
Hi Jeff, You will first have to determine if you system can handle the additional water flow. Then you will replace the UST1102 with the UST1152 along with the Impeller SPX2610C and the Hayward Super Pump Tune Up Kit GOKIT3 or GOKIT3SALT.
MOTOR SCREECHING, PROBABLY NEED A NEW BEARING, CENTURY MODEL NO. C48L2N134B3. PUMP ALSO HAS TROUBLE PRIMING WHAT ELSE DO I NEED. HAYWARD MODEL SP2610X15A
That would be the correct replacement motor. As far as it not priming, it's probably not putting out enough power if it's going bad. When replacing the motor, make sure you replace the shaft seal as well. The part number for that is spx1600z2 and if it's a saltwater pool the part number is 5250-235.
I need a replacement motor for my Hayward Super Pump model number is C48L2N134B1 SELF PRIMING SERIAL NUMBER IS 11514J2, ALSO DOES THE REPLEACEMENT MOTOR COME WITH THE IMPELLER, DIFFUSER, SEAL PLATE AND MOTOR MOUNTING PLATE AND ALL ASSOCIATED PARTS? I basically need everything from the impeller back to the motor if you look at the Hayward diagram.
Hi Bill, yes this is the correct replacement motor for your Hayward C48L2N134B1 motor. This motor does come with the associated parts. We do carry all of these parts which can be viewed or purchased from our Hayward Super Pump Parts Page.
I need a new motor for a Hayward Super pump, since I run my pump most times just to run salt generator. Should I purchase a 2 speed motor to run salt generator and save on electric?
This is going to depend on your foot of head and size of pool. Some salt systems require a minimum flow rate for it to generate chlorine.
I purchased the UST 1152 as a replacement for C48L2N134. After a week of use, the Impeller broke. Is the Impeller SPX2610C compatible with the UST 1152? Should I also purchase the Hayward SPX1600Z2 Seal Assembly? Thanks.
Hi Keith, The UST1152 Motor is compatible with the SPX2610C impeller. These are all parts of the Hayward Super Pump so you are a match there. I would absolutely recommend replacing the HAYWARD SHAFT SEAL whenever you change out the motor. You can also get the Tune Up Kit Hayward Super Pump which includes the shaft seal and all of the o-rings for the Super Pump.
I need the shaft seals
To find the correct shaft seal, we need to know the model number or make and model of your pump's housing. This motor can be mounted on several pump housing, and each one can use a different shaft seal.
I am looking for item # SPX1610Z1M motor for a 1-1/2HP Hayward Super Pump. Can you help me find this?
The correct replacement motor will be the UST1152 A.O. Smith 1.5 HP Round Flange Up Rate Motor.
Looking for replacement motor for a Hayward RS1000, 1.5hp, 3450 rpm, 56J, 115/230 v. Which models are replacements for this?
I was told that a SF 1.3 was more energy efficient than an SF 1.0. Is that true?
The SF (or service factor) when multiplied by the HP (or horsepower) will determine the true HP of your motor, but has no bearing on efficiency per say. For example, if you have a 1.5HP motor with a 1.0SF, you have a true 1.5HP motor. If you have a 1.5HP motor with a 1.1SF, you have a true 1.65 motor.
Hello, I have a motor with model number C48L2N134B1, 1.5 HP, 115/230 Volts, 18 6/9.3 Amps and 3450 RPMs what would be the greatest replacement for this? Thank you!
Hello Chelsea, The correct replacement motor for the model C48L2N134B1 will be the UST1152 A.O. Smith 1.5 HP Round Flange Up Rate Motor.
Our Hayward SP2610X15 motor has gone bad and I'm unsure which motor to order. I've read that http://www.inyopools.com/Products/00200017001331.htm is the direct replacement but its only 1 HP Or Is A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) the direct replacement? Also which seal will be needed?
I have a hayward super pump & just ordered a new motor from your site. c48k2n143c1c. What would be the best seal kit to order for this new motor?
I have an in graund pool pump motor that went bad. It's made by A.O. smith and it's a jacuzzi brand. serial number BY07-14. 1.5 horse power8.0 / 16 .0 amp 230/ 115 volt rpm 3450. let me know with pump motor to get. thank you
Hi Andi, This motor can be used on a Jacuzzi Magnum pump. However, if you can send up more info and or photos we can confirm.
Will this work for model number SP3210Z1M? (1.5 HP) My pool is only about 4-5 years old and the motor has become a lot louder than usual. Should I attempt replacing the bearings or swap the motor.. Or any other suggestions, thanks!
What replacement motor do I need for a Hayward Max Flo II, model number C48D43A04?
The correct motor replacement for your C48D43A04 is the Hayward Max-Flo II 1.5 HP Replacement Motor.
My manual says I need a SPX1610Z1M. Note the X. Does the X make a difference?
Jim, The "X" simply denotes a replacement part. The UST1152 by Century will replace your existing one.
Will these replace a c4sk2n143c1c? To be used for an inground pool.
Hi Nick, Base off of the mod# listed you may have the C48K2N143C1 which the UST1102 motor will replace.
Can I buy a seal kit for this motor
Hi, The seal kits are specifically for the pump, not the motor. If you can provide us with the manufacturer and model of the pump we can locate the correct kit or seals.
What is the difference between a c-face and round flange?
Hi Angie. According to the A.O.Smith/ Century motor technical rep, there is no difference between the terms c-face and round flange.
I received an email saying you answered my question, but I cannot see an answer. I asked "Do you sell A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) motor in its casing with impeller all in one piece so all I have to do is connect the electricity and the 4 bolts to the housing strainer? If so what is the price ?
Bob, Unfortunately they do not come pre-assembled. You would need to order the motor and additional parts separately.
Do you sell this motor in its casing with the impeller all in one piece so all I have to do is connect the electric and the 4 bolts to housing strainer?
Hi Bob, No unfortunately there is not an assembly that is sold this way. Do you know which pump you have? The motor is most commonly used with the Hayward Super Pump and you may find the Hayward Super Pump Impeller here.
How do I know this is the correct pump for my pool. I currently have an a.o smith pump SP1515Z1ESC is the number on it, serial no. 085073M. 1.5 hp for an above ground pool 30 feet around
Hi Lea, The BN35V1 Motor would be the correct replacement for your SP1515Z1ESC
I currently have a dual-speed Super II. The model number on the pump housing is SP3010x152s. The motor itself is A.O. Smith model SP1610Z2MSC7. Would this motor be compatible with my pump body? I have a short pool season so am not worried about the electricity savings of a dual-speed. Thanks
Hi, This UST1152 or the UCT1152 motor will replace the SP1610Z2MSC7 motor.
Is this pump the correct replacement? Current part # is 184982-23 Type-CX
Hi Rob you would actually need the 1.5 HP B229SE Replacement Motor for your 184982-23
will this work for c48l2n134b1
I have the A O Smith ust 1152, C48L2N134C1, 1.5 horsepower, 3450 rpm. It's there a repair kit with gasket or o rings?
Hi Lisa, the gasket kit would be based the manufacture and model of your pump. The most common pumps this motor works on is the Hayward Super Pump and the Hayward Super II Pump. Here is the Tune Up Kit for the Hayward Super Pump and here is the Tune Up Kit for the Hayward Super II Pump. If you have a different pump then please email back and we can supply you with the correct repair kit.
Is this the correct replacement for SP1610Z1M/Model C48L2N134B1? Thank You!
Yes this is the correct replacement motor for a SP1610Z1M / Model C48L2N134B1.
Is this the correct replacement motor for Hayward SP2610X15?
Adam, Yes. This is the correct replacement for the 1.5HP Hayward Super Pump single speed pump.
I need a replacement motor will this one work for me?I have a Hayward pool motor: Model No. C48L2N134B3 Serial No. 07512CH HP 1.5 Volts 115/230 RPM 3450 AMPS 18.6/9.3 Hz 60 SF 1.0 FR 56J PH 1 ENCL ODP
Hello Kenneth, Yes this is the correct replacement motor for the C48L2N134B31 model number you provided.
can youre A.O smith 1.5 HP round Flange up Rate Motor (c48L2N134) does that motor work on mine madelo c48L2Ec11 volts it has 115/230 HP1 RPM 3450 AMPs 19.2/9.6 im just looking for just the motor I got rest hope to hear from you soon
Javier- No the UST1152 A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) will not work, the motor that replaces the C48L2EC11 is the SQ1102 A.O. Smith 1 HP Square Flange Full Rate Motor.
I have an AO Smith ST1152, 3450 RPM 1.5 HP motor. I replaced the capacitor on it a couple of days ago to start it. It is extremely noisy now and I suspect bearings. My motor has the external capacitor on it like the A.O. Smith Round Flange 1 1/2 HP Full Rate Motor. Will the this motor replace the one with external cap? The nomenclature plate seems to have the same specs. I am a commercial HVAC tech and may just replace bearings and seals if available.
Dan- The UST1152 A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) will not replace the ST1152 A.O. Smith Round Flange 1 1/2 HP Full Rate Motor (C1101, ST1152). The ST1152 is full rated and has a higher total horsepower than the UST1152. The Serive Factor on the UST1152 is 1 the Service Factor in the ST1152 is 1.5.
Hi, Looking to replace Model B229SE. Everything matches on the label except for the AMPS. Is this the correct motor? Our label is gone from the actual Hayward Pool Pump section. What else do you recommended purchasing with the replacement motor? Our bearings have gone bad and we do not know how old the actual pump is. Thank you
Your replacement motor is the 5212X. The seals would be dependant on the front pump housing that the motor is bolted to.
NEED STRAINER GASGET SPX1600S AND JACK'S 327
Ron, You can find the Hayward Super Pump Lid gasket Part # SPX1600S if you click here, we do not sell Jack's 327 but we do sell Magic Lube O-ring Lubricant 1 Oz. Teflon Part # 630.
I have a UST1152 C48L2N134C1 . . . . is this the motor I need?
Hello Michael - This is the correct replacement motor.
can i simply upgrade from a 1hp to a 1.5 using the same hook up?
Hi Jeff, You can upgrade to a 1.5 hp motor is your system can handle the additional water flow using the same housing. You will also need to replace the pump impeller and seals.
How do you dismantle the A.O. smith motor C48L2N134B1 from the Haywood pump impeller.
Hi Tony, You can watch out video on How To: Replace the Motor on Your Pool Pump for instructions.
Is this an A.O. Smith or Century motor? I ordeded one and its a century motor.
A.O. Smith is now called Century. It's the same company.
Hi. Looking to replace Model# C48L2N134B1 SP-1610-Z1-M. Will this motor work for me? Just double checking, thanks!
Hi Pete, This will be the correct replacement motor for MOD# C48L2N134B1.
Is the replacement motors new or rebuilt. Is it pretty easy to put a new motor onto your pump. I have no current leaks will I need a shaft seal when I swap motors?
These motors are new. We always recommend a seal kit be purchased when replacing the motor. We would need the model of the front pump housing that the motor is bolted to in order to cross reference the kit.
I have a Hayward max-flo pump model sp2810V15. I have ordered a seal kit for it and need to order a motor -- is this the right one (looks like it is right model number)and do I need a motor shaft seal also? The pump looks in good shape but I saw your comment about replacing the pump if it is ten years old? I don't know how old the pump is?
Hi Danny, This motor, the UST1152 and the Shaft Seal (SPX1600Z2) will be the correct parts for the Max-Flo SP2810X15 pump. If the housing in still in good shape you can replace the necessary parts to get the pump running again.
AO smith super pump motor 1.5 hp Model # C48L2n134b1. what bearings numbers do i needed ? And how meny ? And seal number thank you
Hi Ron, You will need (2) 203 Bearing for this motor, one on either end. Base off of the info provided that is all the info I can provide. If you need the seal I will need to know the manufacturer and model of the pump housing.
hi, do you have also a global version of this motor, i mean in 50/60Hz?
Hi Anthonius, We do not carry a 50/60Hz motor of this kind.
If I have water coming out of the front part of the motor housing do I need a new pump?
Hi Greg, It's possible that you can fix the leak by replacing the seals. If the pump is close or over 10 years old I will recommend that you replace the complete pump.
Is this motor returnable? I am confident it is the right replacement motor for my pool, but I am not confident I can install it. I have watched your video and am willing to try, but in case I fail, can this motor be returned?
Yes you can return product. Please be advised of our return policy here.
Can I use a Variable Frequency Drive with his product in order to change the speed of the motor by changing the frequency?
Hi Miguel, You can not use a VFD with this motor, you will have to replace the entire motor with ECM16CU.VFD can only be used with 5 HP and up motors.
I have a US motors pump cat # EUST1152. Model # c55cxkmc-5013. Water has been leaking from where the motor connects with the rest of the "plumbing". I thought I had a worn gasket but When I removed the motor I didn't find a gasket. Does this model use a gasket and if yes what type/number/size?
Hi Dan, It sounds the your shaft seal needs to be replace, If you can provided the manufacture and model of the pump housing we can locate the correct shaft seal.
Responding to your request for more info. The label is in bad shape, so can't see everything clearly. 1st row: GOULD. 2nd row: Century 1081 Pool Pump Duty. 3rd row: Part: 8-152560-20 | L56J | CS. 4th row: HP: 1. 5th row: Amps: 7.5 / 15.0 | Cont. 6th row: 1.00 | KJB (or KJ8) | B. And finally, in the lower right corner, under "Made in USA" is the number 154479. I hope this will solve the mystery. Thanks for your help!
Hello Steve, The UST1152 A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) is the correct motor for your super pump.
Hi, we have a Hayward Super Pump (SP-1600 Series) and a Gould Century motor with a part number of 8-152560-2D. Is this A.O. Smith motor a suitable replacement?
Hi Steve, I was not able to cross reference p/n 8-152560-2D to this particular motor or any other replacement motor. If you can provide for information off of the motor label we can find the correct replacement motor.
I have a emerson 1081 pool motor EB977 Model R63CXDMR-189 1.5/.18 , dual speed, on a RS 2002 pump. The motor is making ticking noises when running, doesn't sound good. would like to replace motor with an AO equivalent, can you help? thanks in advance very helpful site from reading the many questions
Hello Greg- The correct replacement A.O. Smith motor for your EB977 is the 5388x Motor 56j Thrd Full 2sp 1.5 Hp (B2977, b977, 817706205).
Will this fit my Hayward pool pump model SP3010X15AZ?
Hello Peter - Yes, the UST1152 is the correct replacement motor for Hayward model SP3010X15AZ.
I have a Hayward Northstar pump SP1615-Z-1-BNS 1.5 HP motor for the pool waterfall. I believe it is a 56J frame. Is this the correct motor to replace?
Hello RIch, the correct motor for the Hayward Northstar SP1615-Z-1-BNS will be SN1152.
Can you tell me what is the replacement motor for an AO Smith model K48L2N104, 1 HP, 115/230 volt motor. The SF is 1.5, RPM 3450.
The replacement motor is a CT1102.
Good afternoon, I'm ready to order this from your website but I would like to double check that this is the same motor as: A.O. Smith 1.5 HP motor (model C48L2N134B3) Can you please confirm? Thanks so much! -Allison
Hi Alison, The A.O. Smith 1.5 HP Round Flange Up Rate Motor (UST1152) will be the correct replacement motor.
i currently have a 1 hp pool pump motor UST1102. Can I replace that with the 1 1/2 hp motor 1152? do the have same diameter to bolt up to the pool pump ? Thanks
Mike,You can always increase or decrease your motor size, however, keep in mind if you do so, the sizes of your impeller and diffuser must also match to avoid the motor overheating. Please read out blog, "Biggest Mistakes when Replacing A Motor" for recommendations on increasing your motor size.
Your listing shows that this motor will replace # SP1610Z1M, but can you please confirm that this pump is a suitable replacement with Hayward # SP1610Z1MBK. Thank you!
Matt,Yes, part # UST1152 is the replacement motor for part # SP1610Z1MBK, which is compatible with the Hayward Super Pump.
Will this motor fit on a Hayward Super Pump 193e?
Jettie,Yes this motor will fit several different pumps, including the Hayward Super Pump.
Is the C48L2N134B1 a match for the C48L2N134
Yes, C48L2N134B1 and C48L2N134 are a match.
Is this unit made in USA?
AJ- This product is typically made in either Mexico or China.
HI,IT LOOKS LIKE THIS MOTOR IS A DIRECT REPLACEMENT FOR MY HAYWARD 1 1/2 HP MOTOR.I HAVE 2 QUESTIONS. 1-IS THIS A 110 OR 220 MOTOR.AND 2 -WILL THE PUMP HOUSING ASSY FROM MY FILTER FIT ON THIS REPLACEMENT MOTOR.THANKS FOR YOU TIME.
Hi, The UST1152 Motor can be wired for 110 or 220 volts and will mount onto your existing pump housing.
Hi, my stock number on my motor is USQ1152 , FR 48Y. would this motor fit for replacement . Thanks Matt
No these motors do not have the same mounting frame.
Is the the same replacement motor for Model # C48L2N134B1?
HI David, The A.O. Smith 1.5 HP Round Flange Up Rate Motor (UST1152) would be the correct replacement motor for model # C48L2N134B1.
I have a rs1000, is it possible to change to 1 1/2 hp motor and what all will I have to replace to make the change?
Hi Scott, The RS1000 pump you have is what is called a Full Rated pump. It have a motor that is rated at 1 HP but have a Total HP of 1.5 due to the service factor of the motor. So you do actually have a 1.5 HP motor.
My pump was turned off 24hrs I started it back up and it. Sounded locked up then trip circuit breaker let sit 15 mins try agian trips breaker Is there a internal or external reset ?
Hi Ron, There is not a internal or external reset, it sounds like the motor needs to be replaced.
What is the difference between Model #C48L2N134 and Model #C48L2N134C1? Thanks in advance
These unit are the same. Just alternate part numbers
Is this motor is comparable with C48L2N134B3 model?
Hi Gary yes the UST1152 is the replacement for C48L2N134B3
I have a Hayward Super II, model K48M2N123 (SP-1615-Z1-BEE), and it runs well but recently gets very hot and shuts down or trips the breaker after about 2 hours. Is that a capacitor problem or do I need a motor? Thanks
Here is a How To Troubleshoot a Pool Pump Motor - Motor Shuts Down
WHICH MOTOR WILL REPLACE SP-1540-Z-1B
Hi Jesus, The 1 H.P 115V Thru Bolt Motor (BN25) would be the replacement for the SP-1540-Z-1B motor.
I have Hayward Pool Pump Model No SP3010X154Z. Which Motor should I buy? The existing A.O Smith motor model is P48L2N134B3. It is 1.5 HP motor. It has stopped working.
Hi Bala, I was not able to locate a Hayward pool pump with the model # SP3010X154Z but there is a SP3010X15AZ which would used the A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) motor. You will also need the Hayward Super II Tune Up Kit.
Can I replace a 1.0 hp motor for the jacuzzi magnum with a 1.5 hp motor Replace UST1102 with the UST1152?
Yes you would able to. However please make sure you have 05380209R stamped on your impeller, on your housing seal 02139301r000, and 06015705r000 on your Diffuser.
I have a Pro line SKP712-2V model # PE71 111 V Pump and need a new motor, What motor should I get and will I need a new seal
Hi Pat, The 1.5 H.P 230/115V Thru Bolt Motor (BN35, BN35SS, BN35V1) would be the correct replacement motor for your PE71-III Pump. You would need to replace the shaft seal and o-rings which can be found via the Speck Model E-71 Pump Parts.
I need to replace a Hayward Super Pump (A. O. Smith) 1 1/2 HP pool motor. Model # C48L2N134B1; 115/230 volts; FR 56J. Is this the motor I need? And how can I tell if the motor I'm replacing has a round or square flange? Will I need to replace any seals or gaskets? I have a salt water chlorinator on my pool.
Your motor is indeed a round flange and the seal kit recommended to use is a gokit3salt.
Does this motor replace mine I have a sp1610z1m & does it work on 230 amps.
Hi Mark, The A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) will replace your SP1610Z1M motor and it can be wired for 230 volts.
I need to replace a Hayward Super Pump motor (A.O. Smith), SP1610Z1M, 1.5HP, frame 56J. Is this the correct pump motor?
Hi Hal, The A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134) will be the correct motor based on the part number you provided for your Hayward Super Pump. I would also recommend getting the Hayward Super Pump Tune Up Kit (GOKIT3).
I have this Hayward super pump (A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134b1)). I need a new starting capacitor for it. I'd rather not take it apart again to look at the capacitor to get a new one if I don't have to. Do you know what capacitor is used in this motor? Thank you very much for your help.
I need to replace a Hayward Super Pump (A.O. Smith), SP1610Z1M, 1.5HP, frame 56J, and use a salt water chlorinator. What pump motor and seal kit do I need? Are your seal kits manufactured by Hayward?
HI Hal, You would need the Hayward Super Pump Saltwater Tune Up Kit (GOKIT3SALT). The seal kit is not manufactured by Hayward.
I want to change my motor 5KCR39SN2823AX Marathon electric but on your website i can see that it is unavailable. My question is what other motor would be compatible that I can purchase since the one i need is avaiable?
My A.O. Smith sprinkler pump motor is model C48L2EC11..What is the capacitor required. My capacitor is black, 1.5 in. diam. and 2.75 high. Identification label is essentially gone.
The capacitor you will need is the Capacitor, MFD 161-193 (BC-161) 110-125VAC PART#5270-14
Can I replace the AO Smith 2hp motor with a 1.5 on a hayward super pump?
This will depend on whether you have a square or round flange, the total horse power of the two, and the diffuser/impeller models. You would need to gather the specific motor models and part numbers to confirm compatibility.
I would like to replace this motor with a variable speed motor. Can I just swap them out or will I need to change the pump? Also do you have a model number for the variable speed motor I would need to replace this?
As a variable speed replacement motor you can use the ECM16CU. You would not need to replace any other parts such as the impeller and diffuser as long as they are still rated parts for the 1.5 hp uprated motor.
do you know the difference between the Hayward SPX3015C and 3016C 1-1/2-Horsepower Impeller Replacement for Hayward Super II Pump? Thanks, John
The SPX3015C is the impeller for the 1.5 hp full rate models manufactured after 1988 or the 2 hp uprate models manufactured between 1988-1989. The SPX3016C is the impeller for the 1.5 hp full rate models after 1990 or the 2 hp uprate models after 1990.
Have a Proline pool pump SK P711-15H 1.5hp model# PE71-II-H I'm looking for replacement motor. Would this one work
Hi Sonnie, The replacement motor for you PE71-II-H would be the 1 H.P 115V Thru Bolt Motor (BN25). I would also recommend replace the Shaft Seal Assy (2920060603), you can find other replacement part for you pump via the Speck Model E-71 Pump Parts Diagram.
My Hayward Super Pump 1 1/2 hp just stopped working over the weekend. It was running and just stopped. Upon investigation the breaker was tripped, hoping it was just the storms that were in the area a reset it, unfortunately it tripped again almost immediately. I checked to see if the motor had seized up, I was able to turn it with my fingers, so it's not seized up. Any ideas? Capacitor? If you think it's the capacitor do you sell that? I didn't see it listed on the part break down.
Scott - It may well be the start capacitor especially if you can hear it humming while it is attempting to start. Or it may have failed all together. The start capacitor for the UST1152 motor is 5270-14. Please note that capacitors store an electric charge and should be handled with the utmost caution and care. See our guide on "How To Replace a Pool Pump Capacitor" for more information.
I have a A.O Smith pool pump motor model # S48C51Z03. I am looking for one that water floes out the side and connects to a cartridge filter. All the ones I am seeing water come out the top. I have a shut off valve that fits right between the motor and the cartridge tank.
Jerry, The p/n S48C51Z03 is for the replacement motor which can be used n several different pumps. You can use the Jacuzzi SLR9 1 HP Pump Above Ground Horizontal Discharge (94022430) or the Hayward Matrix Pool Pump 1 HP which has the capability to rotate the discharge.
I have a C48L2N134B1 1-1/2 HP Hayward motor what motor replaces this ? One that comes up is a C1, what's the difference?
Hi Tony, this would be the correct motor for you as there is no difference between C48L2N134B1 and C48L2N134C1 I bleive the B1 and C1 references the lot the motor was manufactured in. So this UST1152 motor on this page is the correct motor for you.
I would like to replace the motor (only) on a Hayward Super Pump. The current motor is 1hp. Can I use the A.O. Smith 1.5 hp motor as a replacement. Thanks in advance.
Yes you can use a 1.5 hp motor but would need to change the impeller if you have a 1 hp uprated model. You also would need to confirm that the filter model that you have is compatible to accept the extra water pressure.
I just bought this motor and I notice it's very hot. Why is it getting too hot? The ventilation ports are no obstructed at all
Ramon, You may want to check the wiring, make sure that you have the correct voltage and make sure that the wires aren't in contact with each other.
My C48l2N134B1 1.5 HP pump is operating on 230VAC. The replacement capacitor listed for it is a 161-193 (BC-161) 110-125VAC. Is this the correct capacitor with the difference between the motor operating voltage and the listed capacitor voltage?
The 161-193MFD 110-125VAC Start Capacitor (BC-161) would be the correct capacitor for the A.O. Smith 1.5 HP Round Flange Up Rate Motor (C48L2N134).
I have a C48L2N134B1 1.5HP and I was told I need to replce the capacitor because the motor is smoking. Is there more than one and what would be the part #?
There is just one capacitor on this motor which is the 610807-002 Start Capacitor.
I have this pump and need to replace the start capacitor. It has been replaced once before but I think the replacement capacitor was the wrong one. Do you have the mfd rating for the original capacitor?
Hi John,We show 610807-002 for the start capacitor on UST1152.
I have a 2 to 4 year old 1 1/2 Hayward Super Pump with an A. O. Smith motor model C48L2N134131 . I need both bearings for that motor. One is bad and I don't know which, so I need both. I don't want to tear it down yet and can use it for short times. Another code # on the motor is SP1610Z1M
Hi Jerry, The part number for both the front and back bearings for a UST1152 motor is 604005-001.
Do I need anything to use this pump in a saltwater pool? Do I need anything to install to my existing super pump base? Thank you
Rick, I would recommend replacing the shaft seal and o-rings when replacing the motor, you can find all the items needed in the Hayward Super Pump Tune Up Kit.
how do you remove the old motor from the pump
Hi Guy, Our Video on How to Replace a Pool Motor goes into detail on how to remove the old motor from your pool pump. The video should cover everything you need but if not then please let us know.
Will the A.O.Smith 1.5H P Part UST1152 Fit my Hayward Superpump HP1 Model- SP2607X10
Hi Bill the UST1152 would not work on your pump, you would need the A.O Smith 1 HP UST1102 Motor.
so, would it be a problem if i replace 1.5hp motor with 1hp b654? thx
This would not be a problem but you would also need to replace your impeller to a 1 HP impeller. If you email us your pump information then we could suggest the correct parts for you.
my pump is jacuzzi magnum 1.5hp: 8-184949-22 cx. screws (4) are on an approximate distance of 15cm (~5.9") across from each other. shaft length is approx 65mm (~2.5") w thread length of 18mm, shaft diameter about 16mm. it is connected to 230v ac, 1.5 hp speed 3450. is this a good replacement? if yes, does it come with 4 big screws or could you provide them for me (will have to cut of existing to release pump bracket). thanks
How long does it take to arrive?
Mark, All in stock motors would be delivered within 3 business days after it is shipped.
Looking for a replacement motor. The tag on my motor reads c48l2n136. What would be a good energy efficient motor for this? Thanks
Hi Dennis, This would be the correct replacment motor for your c48l2n136 motor.
I have a salt pool and a Hayward pump model SP2607X10 with a 1 HP motor. The motor will not turn and I would like to replace it with this motor. Will it fit the pump and what else do I need to complete the installation? (Seals, gaskets, etc.)
John- The sp2607x10 is a 1 HP pump which would require a UST1102 . If you decide to go up in horsepower you would need to change your impeller to a SPX2610C (5110-10a). I would also recommend changing the shaft seal which is part SPX1600Z2 or getting the tuneup kit GOKIT3.
I currently have a magnum jacuzzi 1 1/2 HP model c4822n134c1 that needs to be replaced. What pump do you recommend or do you have one?
Hi Mark, If you are wanting to replace your entire pump then I would suggest the 1-1/2 HP Jacuzzi Magnum Pump. Another option would be to replace the motor on your current pump. If you went this route then you would need the motor listed on this page as well as a Jacuzzi Magnum Tune-Up Kit.
Hi. I have a Hayward Super Pump (self priming with an A.O. Smith 1&1/2hp). The motor appears to be dead - it's model # is C48L2N134B1 (and it's only 3 years old). The one in your ad for $164.99 has almost the same #, but ends in C1, instead of B1. Is it the same unit? If not, what is the difference? Also, are your units new or rebuilt? Thanks.
Hi Mario, yes this is the correct replacement for your C48L2N134B1 motor. When replacing your motor we would suggest a Hayward Super Pump Tune Up Kit. This motor is new and not rebuilt.
Will this work as a replacement for a c48l2n134 b1 and also do I need to purchase the sealer too?
Hi Bob, Yes this would be the correct replacement motor for your pump.
I have a Hayward Pump (SP2615X20) with a Emerson motor (EB796), Cover (SP2600B), Impeller (unknown P/N), Seal plate (SP 2600E5), Motor Plate ( (SP1600F3). I need a new motor (UST 1152), seal and impeller - what parts do I need? What about if I step up to a 2 HP motor (UST 1202)?
Hi Doug, Your Emerson EB796 motor is a 1-1/2 HP Full Rate Motor which is equivalent to the Up Rated 2 HP UST1202 Motor so you would need the UST1202 2 HP motor. The part # of SP2615X20 indicates that your pump is a 2 HP uprated pump so at some point your motor must have been replaced with a 1-1/2 HP full rate motor which is not a big deal since it is the exact same as a 2 HP uprate motor. For your motor replacement I would suggest the Hayward Super Pump Tune Up Kit which includes all the seals and gaskets for your pump. I would also suggest the 2 HP Up Rated Hayward Super Pump Impeller. The ordering of the Motor, Tune Up Kit and Impeller should get you all squared away.
I want to replace my Haywood Super Pump motor, Model C48L2N134B1, UST1152. If I've never done this before, but good at fixing things, would you recommend attempting to do it? Also, if my motor runs but does not draw water into filter, when shutting down there's hum noise, is this a motor issue, or a impeller issue? Not sure what I actually need?
Hi Susan, It will be best to take off the motor and inspect the impeller. There could be a cracked impeller or a clog on that unit. If the motor is humming they it could also be on the way out. We have some how to's to help you trouble shoot this issues. Troubleshoot Motor Install motor
will this pump replace a 1 HP Hayward SP1607 Z 1 M?
The A.O. Smith 1.5 HP Round Flange Up Rate Motor can replace your 1HP Hayward SP1607Z1M motor. You will need to change the impeller and recommend getting a Tune Up Kit. Reply with the model number of your pump housing and I can get you the correct impeller and tune up kit.
Will this motor work with model # C48L2N134B3? Do you ship to Canada?
Hi RC, Yes this would be the correct replacment and yes we do ship to Canada.
I need the wiring diagram as soon as possible for this pump motor my electrician is unfamiliar and does not want to make a mistake and wiring the pumpThe three wires coming out of my pool or black green and white please answer the question referring to only the black and white wires which terminals would he connect them to thank you David Bendik email ocean email@example.com
David, Here's a video on How To Wire A Pool Pump.
will this motor work with model # C48L2N134B1
Yes the UST1152 is the proper replacement for the C48L2N134B1 motor.
Are the bearings serviceable?
Yes the bearings on this motor can be replaced. The UST1152 motor uses Two of The 6203 Bearings.
Looking for a NEW motor for my Magnum Plus Jacuzzi Pump, 1-1/2 hp. Are your motors new. Would also want to replace impeller, diffuser, and what ever else you suggest.
Hi Rich, Yes our motors are new and I would suggest a Jacuzzi Magnum Tune Up Kit if you there are no visible signs of damage on your impeller or diffuser then these parts would not need to be replaced. If you do need to replace these parts then you can view our Jacuzzi Magnum Impeller and Diffuser Guide to help you determine the proper replacements for your pump, or you may view the Jacuzzi Magnume Exploded Parts Diagram.
Want to confirm this is the correct motor to replace my SP2610X15. Thanks in advance
That is correct this is the replacement motor for the SP2610X15
I need a replacement motor for (Leslie's) Hayward HYDRAMAX II with motor part number 10.182261,04 Fr P56J voltage of 208-230/115. Is it this one?
My pump has a amp rating of 18.6 Model #C48L2N134B1 Hayward Super Pump. Do you have a more energy efficient motor? If yes provide model number.
Hello Tom - Model number UCT1152 is the energy efficient version of the UST1152.
When you buy a motor do you get new seals?
Hello Wally - The seals are not included with the motor. The reason for this is that the motor is used on several pumps and each pump takes different seals. You can go to our Pool Pump Parts page to find the correct seals.
I have a Hayward super pump sp1610z1m model C48L2N134B1 1.5 Horsepower Ser 19611CH I need the motor replaced but can not find the exact one. Do you have it.
I installed a new 1 1/2 hp pump over the weekend. Yesterday evening the pump stopped pumping water but the motor was still running just fine. I believe the impeller must have fallen off. Is there a tightening spec for how tight to screw on the impeller?
Steven, The impeller is threaded onto the shaft. The impeller should be threaded on hand tight. Overtightening will cause damage to the motor and impeller.
I currently have the following motor--- Catalog Number: EUST1152 Model: C055KMC5013013J is the supper pump compatible? do you also have the seal kit.(tune up kit}
Hi Tim, Yes this would be the direct replacement for the EUST1152. We do carry the seals but we would need to know the model of your pump to let you know which seal you need. The most popular pump that this motor goes onto is the Hayward Super Pump.
I see that this is the replacement motor for my C48L2N134B1. Now, I just read an entry where a gent asked if the replace motor came with a replace "seal" and the answer was "no". For my motor, does you replace come with one or is a seal even necessary, I don't know? Is it highly recommended? Or is it a Must. And if not included in your Motor, and needed, the Part # and do you carry, is it in stock, and your price? Thanks!
Seals do not come with any replacement motors. Replacing the shaft seal is highly recommended. Lastly we would need the model of the rest of the front plastic model of the pump that the motor mounts to in order to locate the part number and price of the seal.
Is a new pump seal included with the motor?
Hello Mike! No there is not pump seal included with the motor. You would have to look up which pump your UST1152 motor connects to so that you can find out the shaft seal
My pump was leaking so I replaced all the seals but it still leaks. The shaft was pitted from the corrosion would that be the cause of the continued leaking? If it is then does the motor have to be replaced?
MIke - A severely pitted shaft could cause the motor to leak. If it's not the seals or seal plate, it could be the damaged motor shaft.
Will this pump be the replacement for a C48L2N134B3? I see it listed below but want to make sure. If so what is the deal with the different numbers?
Yes that is correct. This motor UST1152 is the replacement for the C48L2N134B3 you had mentioned.
My current motor is a 1.5 hp model K48m2n123. Can I use this(C48L2N134) or do I need to replace it with UST1202. Also do I need any additional parts?
Hello Joe - You would not want to use the C48L2N134. Your current impeller is too heavy for the C48L2N134. The UST1202 would be the correct replacement motor. We would recommend replacing the shaft seal and o-rings. The UST1202 is used on several pumps. You will need to determine the make and model of your pump. Once you have determined the make and model you can find the replacement parts on our Pump Parts page.
I want to upgrade my Hayward Super Pump motor from 1 hp to 1 1/2 hp. Will the UST1152 replacement motor fit the SP2607X10 1hp pool pump?
Yes, the UST1152 would be the correct 1.5HP motor for the Super Pump. If you upgrade the motor, you will need to upgrade the impeller. Part number SPX2610C (5110-10DA) would be the correct impeller for the 1.5HP Super Pump.
Trying to replace Emmerson pool pump motor EUST1152, what motor should I purchase to replace this 1.5 hp motor?
I would sugget this Ao Smith / Century brand motor here which is a direct replacement for the Emerson EUST1152 motor.
Will the AO Smith UCT1152 cost less to run than the UST1152?
Yes, the UCT1152 will cost less to operate compared to the standard UST1152. Depending on how the motor is cared for, it should last several years. When replacing the motor, I would recommend buying a tune up kit based on your pump model and age.
Are all pool motors wired the same?
No. The motor should be wired following the wiring diagram on the motor itself.
My pool pump motor makes a humming noise when I try to start it. Will replacing the motor fix my problem?
Replacing the motor should solve your issues. Aside from the motor, you will need a GOKIT to replace the seals on your pump.
I have a Hayward Supper II single speed 1 1/2 HP pump. What do I need to consider to replace the single speed motor with a dual speed motor?
Check the SF on the old and new motor. The product of the SF and HP has to match. If your old motor has a SF of 1.0, its actual HP is 1.5 (1.5 HP x 1.0 SF). If that's true you should replace it with 1 HP dual speed motor (STS1102). With a SF of 1.5, its actual HP is 1.5 (1.0 HP x 1.5 SF). Also be aware that you will have to buy a hi/lo switch. It is not provided with the motor.
I'm trying to replace the motor on my pool pump but all these numbers and abbreviations on the motor label are really confusing me. What do they mean?
Replacing a pool pump motor is not as difficult as it seems. You can try looking here. If you need help figuring out what the information on your label means. If you are still having difficulty figuring it out you can call us at our toll free number or you can send us a photo of your motor label here.
I'm trying to find a replacement motor for my pool pump but my model number doesn't match what you have listed as the model number. My model number begins with a C48 and yours begins with an SP. Please help.
What we have listed on our chart pages is the pump model number. The model number you have will just identify the motor. If you look on the plastic housing on the pump there should be a sticker which will have the pump model number. You can usually find this by the discharge port on the pump. Once you locate it you can choose the correct replacement motor. Be certain to change the shaft seal and gaskets as needed. You can use our >How to guide if you need help.
Why should I purchase a Tune Up Kit?
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Why do I need to purchase a new shaft seal?
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
What is Service Factor?
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
1 to 2 hrs
1 to 2 hrs
Screwdriver, Pliers, Socket Set
I removed the old motor from the pump housing. I then removed the power cord from the old motor. I removed the cover to the new motor. I verified the new motor was set to the proper voltage which was 230V for my setup. I carefully discharges the capacitor to insure no nasty shock. I then carefully connected the old power cord to the motor and put on the cap. I bolted the new motor to the pump housing and plugged in the pump.
1 to 2 hrs
Screwdriver, Socket Set
1 to 2 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Adjustable Wrench
Best part is the pool motor arrived 2 days earlier than I was expecting. I had some questions about the accesory kit. for the installation..The support was great. I had to upload the picture of my pool motor which he reviewed and suggested the right kit.
The installation was easy once you watch the step by step DIY video provided by inyo pools.
Need to follow the video carefully to avoid leaks. Overall great experience.
Great price.Great support. Recommend highly
1 to 2 hrs
Screwdriver, Nut Drivers, Socket Set
1 to 2 hrs
Screwdriver, Nut Drivers, Wrench Set
Easy direct replacement to the Hayward Super pump. Local pool shop wanted almost 2x the cost of the motor as INYO pools. Online instructions were great, and the follow up emails on how to install the motor made this really easy.
I have replaced the motor before, but it has been over 5 years, so the refresher course/tutorial that was available was very much appreciated.
At first, I did not know how to take the company name, and decided to give them a shot. I am glad I did. I have since purchased additional parts and accessories from this company.
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set
I removed the old motor, switched the impeller over to the new motor, replaced the seals, and reinstalled the new motor. The project was very easy, with the most important part being to shut off the power to the pool before disassembly.
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set
I'm still a novice at pool maintenance.
This is my 3rd summer ever owning a home with a pool.
Opened ourselves with the help of a friend who works in the field.
I have 3 pumps, Main, Spa booster and Waterfall.
The main pump was replaced last year along with a new DE filter and a couple of actuators at a cost of $2000+ by a local company a week before a big party we had planned with 50 guests coming.
After that experience I was done being robbed
This year the Spa pump was right at the end of life (loud as hell) and waterfall pump tripped breaker or would just stop after 30 minutes of run time.
There was no way I was going to go back to the local company.
My friend would have charged me a nominal fee for his time but I figured I would give it a try on my own watching the video and following advice online.
The first pump was a learning curve but the second was a breeze.
The online help and customer service at InYoPools were super helpful.
I recommend also getting a Seal Assembly kit and replace with all new when replacing the motor.
Also which is not noted in the video or article to get a SLINGER FOR the MOTOR SHAFT.
I missed that and had to reopen the first motor and did not find out until I was halfway through the install of the second motor when checking other sites online.
AND be safe everyone. turn off your power to the system before opening anything.
1 to 2 hrs
Screwdriver, Socket Set, Adjustable Wrench
I was fortunate by contacting Inyo and talking to Adam. He convinced me I could handle the replacement process and save some money. He spent time gathering the necessary information to get me the correct motor. He walked me thru the entire process and forwarded a video . I made a call back as I was unsure of the wiring . Once again Adam went over the correct setup. I am happy to report success. Because of people like Adam I will always call Inyo Pool. Your people are your most important Product!!!!!!!!
Less than 1 hr
Screwdriver, Socket Set, Wrench Set
My Haywood pool pump had quite running. When I turned it on it would only hum. Through research I determined that it was needing replaced. I found Inyopool during my online searches. Their prices were the best I found. The replacement was easy. I did order the tuneup kit, as recommended on their site. It took less than 30 minutes to install the tuneup items, and the pump. I referred to the online videos that were provided to me by Inyopool.
For the project you will need a screwdriver, a wrench (to hold the shaft in place while you tighten the impeller), and a socket set.
1. Remove your old pump, and take off the plastic housing that goes from the pump to the filter basket.
2. Clean up the pieces you will be reusing (all the plastic pieces)
3. Replace your shaft seal parts, be sure to lube the areas shown in the video
4. Now you can attach all the plastic parts onto your new pump.
5. Tighten the 4 bolts being sure to tighten each snug, before tightening all.
6. Attach your power wires, and your ground wires, put the back cover on and turn your breakers back on.
7. Final step is to refill the filter basket with water, once it is full, your new pump will be ready to roll.
Biggest recommendation is to watch the Inyopool videos. I am a female, and I was able to complete this without any problem, thanks to their step by step videos.
2 to 4 hrs
Screwdriver, Pliers, Socket Set, Adjustable Wrench
The motor was removed from the pump housing and inspected. It had locked up due to moisture from a leaking housing. A new motor and seal kit was ordered for replacement, delivery was made in 2-3 days and the repair was completed using instructional videos on the INYO website. This was my first attempt at a pump repair and everything went smoothly. Thanks to INYO for the quick delivery of parts and detailed instructions on the repair!
(5 out of 5 stars) Excellent Pump Moter Replacement
Reviewed By: PoJo from Clarence, NY ()
Pros: Awesome fit - excellent replacement
Tip to get the impeller off the old pump moter: use a 7/16" open ended wrench - it slides in near the capacitor on the electrical side... rotate the impeller until the wrench slides into place at the end of the shaft and then one person holds the motor and the wrench while a 2nd person loosens the impeller off with bare hands by turning the impeller counter clock-wise.
(5 out of 5 stars) A GREAT EXPERIENCE!!!
Reviewed By: ()
This motor worked perfectly on my Hayward DE filter. INYOpools.com was very helpful to make sure I purchased the right motor and seal kit as well. I am extremely satisfied with the customer service, the product, and the delivery time. Excellent!!!