Part # SPX0715D
By Hayward Pool Products
Part # SPX0715D
Dimensions 6.375" L x 6.375" W x 0.35" D
Hayward 2 VariFlo Valve Seat Gasket
I have a Hayward DE 4800 pool filter with a Hayward vari-flo valve. I need the spider gasket but the label is worn and I don't know which model I have. Either SP-710 or SP-715. Is the gasket the same for both?
The sp710 has 1.5" ports and the sp715 has 2" ports so yes, the spider gaskets are going to be different. What is your port size and I can provide the correct spider gasket?
Does the ribbed side of the gasket face up or down? Should you use a lubricant to help move from various positions such as filter or backwash?
Hello, The ribbed side of your gasket should be facing up, if you would like to watch a video on How to Replace a Spider Gasket on a Multiport Valve. I would not recommend using lubricant to help move gasket to positions.
Will this gasket fit a Hayward SP-715-A-6 multiport? Thanks
Hi, Lee. Based on the model number provided this is the correct diverter gasket.
I have a Hayward Multiport Valve, SP0714T, 1-1/2" Top Mount, 6 Pos I need a new vaule gasket ..
The Hayward Multiport Variflo XL 1 1/2" SP714T only offers the Valve Seat Gasket by ordering the Key/seal Assembly (Diffuser w/ Gasket Glued In) (spx0714ca).
How wide are the spokes and rings of the gasket, I have an older valve and the numbers and brand have worn off of the top. I need them to be 3/15th wide.
What model filter do you have? I can figure out the correct spider gasket for your valve with that information.
I have a variflo valve mod nr. spo710x62fv. Is there a rebuild gasket kit for this? If so, what is the kit number?
Hi James, There is not a gasket rebuild kit available for the SP0710X62 valve the parts will have to purchase the parts separately. The parts can be founds on the Hayward Multiport Vari-Flow Parts page.
My vari flo valve is SP710XR50. What seat gasket will fit?
Steve, Yes, this will fit the SP0710XR50 valve.
I have an older sand filter, PAC-FAB SP-715 SAND, but when I search all I come up with is Hayward SPx715. Will the Hayward gasket fit my PAC-FAB filter valve? Also what adhesive do you recommend and what particular acetone free nail polish remover do you recommend to remove the old adhesive? Thx
Looking for a 5-sprocket gasket for our Hayward IS-210T-98 sand filter control valve... Seems to be about 6 inches in diameter...
Joanne, Please provide the model number of the valve.
Will this seat gasket work for Model #S210T Sand Filter? Please advise, If no , advise the correct gasket.
Hi Warren, The valve used on the Hayward S210T sand filter is the SP0714T valve and this spider gasket does not work on the SP0714T valve. For the SP0714T valve the spider gasket is only available with the Diverter Assembly with Glued in Spider Gasket
I have a Hayward S166T high rate sand filter and need to replace the valve seal gasket. Which one would I need.
The correct replacement gasket between the valve and the tank is O-ring, Id 6-3/4", Od 7-1/8" - 364. If you were referring to the SPIDER gasket that is inside the multiport valve and your valve model is SP0714T, then the correct replacement part is Key/seal Assembly (Diffuser w/ Gasket Glued In). The spider gasket comes glued in this diffuser.
Will a damaged spider gasket cause sand to get into the pool?
Hello, A damaged spider gasket is not a typical cause of sand leaking into the pool. You most likely have a damaged lateral or main pipe inside the sand filter.
I have a SP715XR50 Hayward valve on my pool. Will this replace the gasket I currently have??
Hello Tom, Yes this gasket will replace the gasket for the Hayward Vari-Flo Valve Assembly SP0715RX50.
Is this glued in? I had replaced it some years back and I seem to remember being told to superglue it in, but am not sure and want to be ready for when I open her up. I have the Hayward Vari-Flo Multi-Port Valve SP0715 (was SP71) assembly (top is cracked, so I need to replace both).
Hello Al, There is no way to know definitively if your gasket is glued in or not until you begin to remove the spider gasket. If you need additional assistance, here is a link to the How to Replace a Spider Gasket on a Multiport Valve instructional video.
How can I find a model number on vary-flo unit?
Mary, The part number for your vari-flo would be on the label on top that has the backwash,filter and rinse options.
If a piece of the gasket is worn away will it cause it to leak in filter mode?
Tony, Yes, a damaged spider gasket will cause the valve to leak from the waste port while set to the filter position.
Will this gasket replace the one on a S180T valve? Thanks.
Marty - No this gasket will not work on the multiport valve, SP0714T, used on a S180T filter. For the SP0714T valve the spider gasket is only available with the Diverter Assembly with Glued in Spider Gasket. The gasket is not sold separately.
Will this fit a Hayward pro series s220t
Hi Roy, The valve used on the Hayward S220T sand filter is the SP0714T valve and this spider gasket does not work on the SP0714T valve. For the SP0714T valve the spider gasket is only available with the Diverter Assembly with Glued in Spider Gasket.