Model # PLC1400
Warranty One Year
Alternate Part #'s JDYPLC1400
Jandy Replacement Salt Cell PLC1400
Utilizing ordinary salt, the electrolytic AquaPure cell generates free chlorine for your pool. As the salt in the water passes through the AquaPure cell, it converts to free chlorine and continuously kills bacteria and algae while maintaining the desired sanitization you need to keep your water pure and clean. When the chlorine is finished purifying the pool water, it converts back into salt and the whole cycle repeats.
Easy, economical and automatic – simply set the chlorine levels and AquaPure takes care of the details. You'll have more time to enjoy your pool and spa with AquaPure! AquaPure and PureLink are the only salt chlorine generation systems that communicate with wired and wireless AquaLink RS Controls.
Size: For pools up to 40,000 Gallons
Input: 115 VAC, 50/60 Hz, 1.5 amps
230 VAC, 50/60 Hz, 0.75 amps
Output: 22-30 vdc @ 3 amps maximum
Chlorine: 0.625 Lbs per 24 hour (283 gm / 24 Hr.)
PLEASE NOTE: The PLC700's have a 2 prong plug system and the PLC1400's have a 3 prong plug system.
I have discontued using my Aqua Pure 1400. Is the a blank I can get so I can take the 1400 out entirely.
I have an older Jandy Aquapure system where the salt cell is only has 2 ports, and now they have 3. I think the control system is also getting old and functioning properly. Is there a specific system which is best or easiest to replace it with where the new cell that I install will fit in the same dimensions of the Jandy that I am removing?
Hi, Brian. There is not another system that can be used as a drop-in replacement for the AquaPure Systems.
I have the Jandy IAqualink RS and ready to bring in a salt generator. Do I need just the PLC1400 or PLC1400 + power center? Does the PLC1400 come with everything as a kit to go direct into my IAqualink?
Hi, Kelly. If you have one of these compatible power centers, 6614AP-L or 6613AP you can just purchase the AquaPure 1400 Cell Kit - PLC1400. If not, then you will need the AquaPure Power Center - APUREM and the AquaPure 1400 Cell Kit - PLC1400.
WAT IS E PRICE OF THIS PART?,IF YOU SEND IT IN FRANCE?
THANKS FOR YOUR ANSWER
Hi Peitrequin, the shipping to France would be $139 we will send you over a quote and if you would like to place an order you may do so directly through the emailed quote.
I have the PLC 1400 working now for 3 seasons . I have a service indicator saying to clean the cell. I paid someone to look at the cell and it was clean. Do I need to purchase another unit just after 3 seasons
I have an aqua link pure control system .Are the boards or the complete box still available?
Hi. Yes, replacement parts and the complete controller are available for Jandy Aqua Pure 1400 unit. We just need to know the model of the controller you have.
I've got the Jandy 1400 PLC, I've replaced the cell with the new external flow meter. twice in the last few weeks.My problem is after shocking the pool to bring the chlorine up, it appears the system is not making chlorine, all the electrical connects are showing correct voltage, salt is showing 3.3, PH 7.4-7.6, but after a couple of days..no chlorine and low alkalinity..thoughts? Thanks in advance
I have an aquapure700 salt/chlorine system. The salinity indicator on the control unit reads 0.0 for salt content. I have added 160 lbs of pool salt and have had the water tested. Based on the water sample test, it should be reading about 3.0. Why is the control system not showing any salt.
Hi Tim, The problem could be the Tri-Sensor or the control panel, it's hard to say which one.
Do you offer the cell by itself without the sensor and cable? I recently replaced the sensor so I don't need that. Also, is there a way to test the cell to determine if it is bad? The last several water tests that were done show that the chlorine level is way too low. The salinity has been kept in range and I adjusted the chlorine production rate up to 100%. We've even shocked with liquid chlorine regularly but our water tests from the local pool store continue to indicate low chlorine levels.
Hi Rusty, The AquaPure Cell is only sold as a kit. There is no way to test the cell directly other than the ability to confirm that you're getting and holding a chlorine in your pool.
Is the salt included with the salt chlorine generator?
No, salt is not included. You would purchase the salt locally and the quantity will depend upon the number of gallons of water in your pool. Use a salt that is at least 99.8% pure NaCl. The preferred salt is evaporated, granulated, food quality, and NON-iodized. Avoid using salt with anti-caking agents like sodium ferrocyanide, also known as yellow YPS (prussiate of soda). These cause some discoloration of fittings and pool surface finishes. DO NOT use calcium chloride.
Less than 1 hr
I was getting an error 125 and 194. Cleaned the cell and the codes continued. Ordered this cell due to the price and new style flow sensor included. Easily replaced the cell, o-rings, power cord, and flow sensor. The cell was easy to replace by unscrewing the unions and matching the flow direction of the plumbing. Easy repair that saved hundreds of dollars.
(5 out of 5 stars) Works Great Cell Kit
Reviewed By: Ann B. from Norman OK ()
Our cell went out and we replace this one with the old which had a different plumbing connection, but with help from our pool contractor we were able to install it without a hitch, WORKS GREAT!
(5 out of 5 stars)
Reviewed By: ()
I was a bit hesitant but decided to install this one myself to replace the existing PLC1400. The cell itself is easy, the wiring is a bit more intimidating. Read the directions, read them again, cut the power, take your time and you can do it!
(5 out of 5 stars) Real OEM replacement part.
Reviewed By: ()
The new salt cell fit perfectly into the space where the old one was and within two days the free chlorine level was where it should be. I did not need the sensor since I replaced the old one less than a year but now I have a spare when it wears out.